Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Brake Warning Light Remains ON  


DESCRIPTION

This procedure is for troubleshooting when the brake system warning light (red indicator) remains on but no DTCs are output.

The skid control ECU (brake actuator assembly) controls the brake system warning light (red indicator) in the combination meter assembly via CAN communication.

WIRING DIAGRAM

C427356E09
5.667,0.469 5.979,0.667 0.313,0.198 10 false 19 5.729,1.083 6.042,1.281 0.313,0.198 10 false 5 5.969,0.688 6.583,0.885 0.615,0.198 10 false CANL 5.969,1.281 6.583,1.479 0.615,0.198 10 false CANH 5.583,4.573 6.042,4.771 0.458,0.198 10 false A34 5.573,4.719 7.104,5.167 1.531,0.448 10 false Skid Control ECU (Brake Actuator Assembly) 0.75,0.677 1.365,0.875 0.615,0.198 10 false CANL 0.719,1.292 1.333,1.49 0.615,0.198 10 false CANH 1.229,0.51 1.542,0.708 0.313,0.198 10 false 31 0.802,2.615 1.417,2.813 0.615,0.198 10 false VCM 0.885,4.25 1.5,4.448 0.615,0.198 10 false SW 1.219,1.073 1.531,1.271 0.313,0.198 10 false 32 1.271,2.573 1.583,2.771 0.313,0.198 10 false 7 1.24,4.25 1.552,4.448 0.313,0.198 10 false 12 1.906,2.594 2.219,2.792 0.313,0.198 10 false 2 3.156,2.594 3.469,2.792 0.313,0.198 10 false 1 1.583,3.115 2.042,3.313 0.458,0.198 10 false A2 1.615,4.906 2.073,5.104 0.458,0.198 10 false A1 1.604,5.094 4.104,5.615 2.5,0.521 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly) 1.583,3.271 4.01,3.625 2.427,0.354 10 false Vacuum Warning Switch Assembly 3.938,6.125 5.854,6.49 1.917,0.365 10 false : CAN Communication Line 0.063,6.094 1.979,6.51 1.917,0.417 10 false Combination Meter Assembly 1.833,4.26 2.146,4.458 0.313,0.198 10 false 1 3.771,4.271 4.083,4.469 0.313,0.198 10 false 2 0.073,5.896 0.531,6.094 0.458,0.198 10 false K21 2.031,4.479 2.344,4.677 0.313,0.198 10 false + 3.552,4.49 3.865,4.688 0.313,0.198 10 false E 2.104,2.833 2.417,3.031 0.313,0.198 10 false + 2.917,2.844 3.229,3.042 0.313,0.198 10 false E

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Before performing this procedure, depress the brake pedal and confirm that the stop lights illuminate.



PROCEDURE

1.PRE-CHECK
a.

Check that all of the following conditions required for the brake system warning light (red indicator) to turn off are met:

i.

The ABS warning light are not illuminated.

HINT:

If the ABS warning light remains illuminated, make sure that the conditions required for the ABS warning light to turn off are met.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>ABS Warning Light Remains ON



ii.

The brake fluid level in the brake master cylinder reservoir assembly is not low.


iii.

Ensure that the brake booster has sufficient vacuum.

HINT:

When the vacuum inside the brake booster decreases, the brake system warning light (red indicator) comes on.




Result:
Proceed to
NEXT



NEXT

2.CHECK VEHICLE CONTROL HISTORY (RoB) (VEHICLE STABILITY CONTROL SYSTEM AND ELECTRIC PARKING BRAKE SYSTEM)
2.CHECK VEHICLE CONTROL HISTORY (RoB) (VEHICLE STABILITY CONTROL SYSTEM AND ELECTRIC PARKING BRAKE SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Chassis / Brake/EPB / Utility / Vehicle Control History (RoB).


d.

Using the GTS, check for Vehicle Control History (RoB).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>VEHICLE CONTROL HISTORY (RoB)

Chassis > Brake/EPB > Utility
Tester Display
Vehicle Control History (RoB)
50005 435 55
HINT:

If vehicle control history (RoB) is stored when the vehicle stability control system and electric parking brake system are suspended, the brake system warning light (red indicator) illuminates.



Result:
Result Proceed to
There is no vehicle control history (RoB) for when the vehicle stability control system and electric parking brake system were suspended. A
There is vehicle control history (RoB) for when the vehicle stability control system and/or electric parking brake system were suspended. B



A

3.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

B

PERFORM TROUBLESHOOTING AND REPAIR REGARDING VEHICLE CONTROL HISTORY (RoB)

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>VEHICLE CONTROL HISTORY (RoB)

NOTICE:

After performing troubleshooting and repair regarding vehicle control history (RoB), clear the vehicle control history (RoB).



3.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY
a.
C230719C35
2,1.99 2.51,2.813 true 1.458,1.99 0.958,2.813 true 0.365,0.302 0.594,0.49 0.229,0.188 10 false *a 2.563,2.844 2.719,3.031 0.156,0.188 10 false + 0.844,2.865 1,3.052 0.156,0.188 10 false E
*a Component without harness connected
(Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A1 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the reservoir. Its position changes according to the brake fluid level.


Standard Resistance:
Tester Connection Condition Specified Condition
1 (+) - 2 (E) Switch off (float up) 1.9 to 2.1 kΩ
1 (+) - 2 (E) Switch on (float down) Below 1 Ω



e.

If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the K21 combination meter assembly connector.


c.

Disconnect the A1 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K21-12 (SW) - A1-1 (+) Always Below 1 Ω
K21-12 (SW) or A1-1 (+) - Body ground Always 10 kΩ or higher
A1-2 (E) - Body ground 1 minute or more after disconnecting the cable from the negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT VACUUM WARNING SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT VACUUM WARNING SWITCH ASSEMBLY
a.

Inspect the vacuum warning switch assembly.

Click hereBrake>BRAKE SYSTEM (OTHER)>VACUUM WARNING SWITCH>ON-VEHICLE INSPECTION

OK:

The vacuum warning switch assembly is normal.



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - VACUUM WARNING SWITCH ASSEMBLY)

NG

REPLACE VACUUM WARNING SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - VACUUM WARNING SWITCH ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the K21 combination meter assembly connector.


c.

Disconnect the A2 vacuum warning switch assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K21-7 (VCM) - A2-2 (+) Always Below 1 Ω
K21-7 (VCM) or A2-2 (+) - Body ground Always 10 kΩ or higher
A2-1 (E) - Body ground 1 minute or more after disconnecting the cable from the negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT COMBINATION METER ASSEMBLY
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


d.

Perform the Active Test of the combination meter assembly using the GTS.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
Brake Warning
50004 409 107

e.

Check the combination meter assembly.

OK:

The brake system warning light (red indicator) turns on or off in accordance with GTS operation.



Result:
Proceed to
OK
NG



OK

NG