Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C13807F  Stop Lamp Relay Actuator Stuck Off  


DESCRIPTION

Refer to DTC C13807E.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C13807E

DTC No. Detection Item DTC Detection Condition Trouble Area
C13807F Stop Lamp Relay Actuator Stuck Off When the voltage at the +BS terminal is between 10 V or more and the stop light control relay (stop light switch assembly) drive output (STPO) is on, a signal is not input to the STP2 terminal for 5 seconds or more.
·

Wire harness or connector

·

Stop light switch assembly

·

Skid control ECU (brake actuator assembly)

·

Rear combination light assembly LH

·

Rear combination light assembly RH

·

Center stop light set



CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION



HINT:

When DTC P057111, P057112 and/or P057113 are output together with DTC C13807F, inspect and repair the trouble areas indicated by DTC P057111, P057112 and/or P057113 first.

P057111: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>P057111

P057112: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>P057112

P057113: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>P057113


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed.

OK:

The stop lights illuminate.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS (STOP LAMP RELAY)

NG

6.CHECK STOP LIGHT OPERATION
2.PERFORM ACTIVE TEST USING GTS (STOP LAMP RELAY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Chassis / Brake/EPB / Active Test.

Chassis > Brake/EPB > Active Test
Tester Display Measurement Item Control Range Restrict Condition Diagnostic Note
Stop Lamp Relay Stop light control relay (Stop light switch assembly) Relay OFF / ON Vehicle condition: Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


With the brake pedal released, check that the stop lights illuminate and the value of Stop Light Relay on the GTS changes to ON when Stop Lamp Relay is ON
Chassis > Brake/EPB > Active Test
Tester Display
Stop Lamp Relay
50004 435 27

d.

According to the display on the GTS, perform the Active Test and check the operation of the stop lights.

OK:

Stop lights turn on in accordance with the Active Test.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SIGNAL INPUT CIRCUIT)

NG

4.INSPECT STOP LIGHT SWITCH ASSEMBLY (ACC TERMINAL VOLTAGE)
3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SIGNAL INPUT CIRCUIT)
a.
C399487C77
0.344,0.229 0.729,0.479 0.385,0.25 2.438,0.938 2.583,0.344 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 0.406,0.271 0.865,0.469 0.458,0.198 10 false A34 2.469,0.177 2.854,0.417 0.385,0.24 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-44 (STP2) - Body ground Brake pedal depressed 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT STOP LIGHT SWITCH ASSEMBLY (ACC TERMINAL VOLTAGE)
a.
C440416C25
0.448,0.448 0.781,0.698 0.333,0.25 2.083,1.656 1.729,1.021 true 0.188,0.177 0.5,0.333 0.313,0.156 10 false *a 0.5,0.49 0.958,0.688 0.458,0.198 10 false A85 2.021,1.688 2.479,1.885 0.458,0.198 10 false ACC
*a Component with harness connected
(Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A85-4 (ACC) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.
C399487C78
0.344,0.229 0.729,0.479 0.385,0.25 2,1.302 2.052,1.875 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 0.406,0.271 0.865,0.469 0.458,0.198 10 false A34 1.906,1.906 2.448,2.125 0.542,0.219 10 false STPO
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-10 (STPO) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK STOP LIGHT OPERATION
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Check that the stop lights come on when the brake pedal is depressed.

OK:

The stop lights illuminate.



Result:
Proceed to
OK
NG



OK

NG

7.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)
7.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)
a.
C427377C05
0.333,0.448 0.75,0.698 0.417,0.25 0.896,1.74 1.521,1.344 true 0.396,0.49 0.781,0.698 0.385,0.208 10 false W13 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 0.583,1.729 1.042,1.927 0.458,0.198 10 false STP
*a Front view of wire harness connector
(to Rear Combination Light Assembly LH)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the W13 rear combination light assembly LH connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
W13-2 (STP) - Body ground Brake pedal depressed 11 to 14 V



Result:
Proceed to
OK
NG



OK

GO TO LIGHTING SYSTEM (REAR COMBINATION LIGHT ASSEMBLY LH (STOP LIGHT CIRCUIT))

Refer to "Left or right stop light does not illuminate" of problem symptoms table.

w/ Automatic Headlight Beam Level Control System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System)>PROBLEM SYMPTOMS TABLE

w/o Automatic Headlight Beam Level Control System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Automatic Headlight Beam Level Control System)>PROBLEM SYMPTOMS TABLE


NG

8.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY RH)
8.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY RH)
a.
C427377C06
0.333,0.448 0.75,0.698 0.417,0.25 0.969,1.74 1.521,1.333 true 0.385,0.49 0.771,0.698 0.385,0.208 10 false W12 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 0.74,1.76 1.198,1.958 0.458,0.198 10 false STP
*a Front view of wire harness connector
(to Rear Combination Light Assembly RH)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the W13 rear combination light assembly LH connector.


d.

Disconnect the W12 rear combination light assembly RH connector.


e.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
W12-2 (STP) - Body ground Brake pedal depressed 11 to 14 V



Result:
Proceed to
OK
NG



OK

GO TO LIGHTING SYSTEM (REAR COMBINATION LIGHT ASSEMBLY RH (STOP LIGHT CIRCUIT))

Refer to "Left or right stop light does not illuminate" of problem symptoms table.

w/ Automatic Headlight Beam Level Control System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System)>PROBLEM SYMPTOMS TABLE

w/o Automatic Headlight Beam Level Control System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Automatic Headlight Beam Level Control System)>PROBLEM SYMPTOMS TABLE


NG

9.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - CENTER STOP LIGHT ASSEMBLY)
9.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - CENTER STOP LIGHT ASSEMBLY)
a.
C401718C15
0.281,0.365 0.656,0.615 0.375,0.25 1.188,1.594 1.604,1.177 true 0.344,0.396 0.802,0.594 0.458,0.198 10 false R47 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.073,1.594 1.229,1.792 0.156,0.198 10 false B
*a Front view of wire harness connector
(to Center Stop Light Set)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the W13 rear combination light assembly LH connector.


d.

Disconnect the W12 rear combination light assembly RH connector.


e.

Disconnect the R47 center stop light set connector.


f.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R47-1 (B) - Body ground Brake pedal depressed 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)
10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the W13 rear combination light assembly LH connector.


d.

Disconnect the W12 rear combination light assembly RH connector.


e.

Disconnect the R47 center stop light set connector.


f.

Disconnect the A85 stop light switch assembly connector.


g.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A85-1 (OUT) - W13-2 (STP) Always Below 1 Ω
A85-1 (OUT) or W13-2 (STP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR