Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER › from 2021.02
RM33A0E _59 Vehicle Exterior _065397 EXTERIOR PANELS / TRIM _0319662 FRONT BUMPER A

EXTERIOR PANELS / TRIM  FRONT BUMPER  REASSEMBLY  


PROCEDURE

Hide 52536 1.INSTALL FRONT BUMPER SIDE RETAINER LH

a.
B470417C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 clips as shown in the illustration.


b.
B470415

Install the front bumper side retainer LH with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 52535 2.INSTALL FRONT BUMPER SIDE RETAINER RH

HINT:

Use the same procedure as for the LH side.


Hide 52131A 3.INSTALL FRONT BUMPER REINFORCEMENT

a.

Install the front bumper reinforcement with the 6 bolts.

B481987

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


b.
B481986

Engage the 4 clamps.



d.

Install the headlight assembly RH.

HINT:

Use the same procedure as for the LH side.



Hide 52611 4.INSTALL FRONT BUMPER ENERGY ABSORBER

a.
B489579C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 guides to install the front bumper energy absorber as shown in the illustration.


Hide 53879H 5.INSTALL FRONT FENDER LINER RETAINER

a.
B479551C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws to install the 2 front fender liner retainers as shown in the illustration.

HINT:

Use the same procedure for the RH side and LH side.



Hide 47749F 6.INSTALL PIN HOLD CLIP

a.
B610732C02
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 claws to install the 2 pin hold clips as shown in the illustration.

HINT:

Use the same procedure for the RH side and LH side.



Hide 52713A 7.INSTALL FRONT BUMPER SIDE MOULDING LH (for Mesh Type Radiator Grille)

a.
B604944

Engage the 2 guides and 2 claws.


b.
B604943

Install the front bumper side moulding LH with the 2 clips.


Hide 52712 8.INSTALL FRONT BUMPER SIDE MOULDING RH (for Mesh Type Radiator Grille)

HINT:

Use the same procedure as for the LH side.


Hide 52112C 9.INSTALL FRONT BUMPER EXTENSION (for Bar Type Radiator Grille)

for GR SPORT:

HINT:

When installing the front bumper extension, heat the lower radiator grille sub-assembly using a heat light.


Heating Temperature
Item Temperature
Lower Radiator Grille Sub-assembly 20 to 30°C (68 to 86°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the lower radiator grille sub-assembly excessively.


a.

Clean the lower radiator grille sub-assembly surface.

i.

Using a heat light, heat the lower radiator grille sub-assembly surface.


ii.

Wipe off any tape adhesive residue with cleaner.



b.

Remove the release paper from a new front bumper extension.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



c.

Install the front bumper extension as shown in the illustration.

B609268

HINT:
·

Attach the front bumper extension from the center outwards as shown in the illustration.

·

Press the front bumper extension firmly to install it.




Hide 53102A 10.INSTALL LOWER RADIATOR GRILLE SUB-ASSEMBLY (for Bar Type Radiator Grille)

a.

Engage the 17 claws.

B607500


b.
B607499

Install the lower radiator grille sub-assembly with the 4 screws.


Hide 53102A 11.INSTALL LOWER RADIATOR GRILLE SUB-ASSEMBLY (for Mesh Type Radiator Grille)

a.

Engage the 6 guides and 24 claws.

B607502


b.
B607501

Install the lower radiator grille sub-assembly with the 4 screws.


Hide 53122G 12.INSTALL LOWER CENTER RADIATOR GRILLE MOULDING (for Mesh Type Radiator Grille)

a.

Engage the guide and 4 claws.

B607498


b.
B607497

Install the lower center radiator grille moulding with the screw.


Hide 52534 13.INSTALL FRONT NO. 2 BUMPER RETAINER BRACKET (for Mesh Type Radiator Grille)

HINT:

When installing the front No. 2 bumper retainer bracket, heat the front bumper cover using a heat light.


Heating Temperature
Item Temperature
Front Bumper Cover 20 to 30°C (68 to 86°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front bumper cover excessively.


a.

Clean the front bumper cover surface.

i.

Using a heat light, heat the front bumper cover surface.


ii.

Remove any remaining double-sided tape from the front bumper cover.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Remove the release paper from a new front No. 2 bumper retainer bracket.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



c.
B606197C03
0,0 0,0 false
V100155

Double-sided Tape


Engage the claw and attach the double-sided tape to install the front No. 2 bumper retainer bracket.

HINT:

Press the front No. 2 bumper retainer bracket firmly to install it.



Hide 52533 14.INSTALL FRONT NO. 1 BUMPER RETAINER BRACKET (for Mesh Type Radiator Grille)

HINT:

Use the same procedure as for the LH side.


Hide 53124D 15.INSTALL LOWER RADIATOR GRILLE MOULDING LH (for Mesh Type Radiator Grille)

a.
B607496

Engage the guide and 8 claws.


b.
B607495

Install the lower radiator grille moulding LH with the screw.


Hide 53123C 16.INSTALL LOWER RADIATOR GRILLE MOULDING RH (for Mesh Type Radiator Grille)

HINT:

Use the same procedure as for the LH side.


Hide 81482C 17.INSTALL FOG LIGHT COVER LH (for Mesh Type Radiator Grille)

a.
B607494

Engage the 6 claws.


b.
B607493

Install the clip.


c.
B607492

Install the fog light cover LH with the 4 clips.


Hide 81481E 18.INSTALL FOG LIGHT COVER RH (for Mesh Type Radiator Grille)

HINT:

Use the same procedure as for the LH side.


Hide 52713A 19.INSTALL FRONT BUMPER SIDE MOULDING LH (for Bar Type Radiator Grille)

a.
B607491

Engage the 2 guides and 3 claws.


b.
B607490

Install the front bumper side moulding LH with the 5 screws.


Hide 52712 20.INSTALL FRONT BUMPER SIDE MOULDING RH (for Bar Type Radiator Grille)

HINT:

Use the same procedure as for the LH side.


Hide 81220 21.INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)

Hide 81210A 22.INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:

Use the same procedure as for the LH side.


Hide 53101 23.INSTALL RADIATOR GRILLE SUB-ASSEMBLY (for Bar Type Radiator Grille)

a.
B607486

Engage the guide and 10 claws.


b.
B607485

Install the radiator grille sub-assembly with the 2 screws.


Hide 53101 24.INSTALL RADIATOR GRILLE SUB-ASSEMBLY (for Mesh Type Radiator Grille)

a.
B607489

Engage the 8 claws.


b.
B607488

Install the 10 screws.


c.
B607487

Install the radiator grille sub-assembly with the 2 clips.


Hide 52111F 25.INSTALL FRONT CENTER BUMPER BAR (for Bar Type Radiator Grille)

a.
B607484C01
1.042,0.188 1.354,0.344 0.313,0.156 10 false *a 0.646,0.24 0.958,0.396 0.313,0.156 10 false *b 2.563,0.063 2.875,0.219 0.313,0.156 10 false *a 1.448,0.115 1.76,0.271 0.313,0.156 10 false *b 2.208,0.052 2.521,0.208 0.313,0.156 10 false *b 2.885,0.063 3.198,0.219 0.313,0.156 10 false *b
*a Clip
*b Screw


Install the 4 screws.


b.

Install the front center bumper bar with the 2 clips.


Hide 26.INSTALL FRONT BUMPER UPPER RETAINER

HINT:

Use the same procedure for the RH side and LH side.


a.
B596565

Engage the 2 guides.


b.

Install the front bumper upper retainer with the screw.


Hide 75310A 27.INSTALL RADIATOR GRILLE EMBLEM ASSEMBLY

a.
B596564

Engage the guide and 4 claws.


b.
B596563

Install the radiator grille emblem assembly with the screw.


Hide 53395E 28.INSTALL HOOD TO FRONT END PANEL SEAL

HINT:

When installing the hood to front end panel seal, heat the front bumper cover using a heat light.


Heating Temperature
Item Temperature
Front Bumper Cover 20 to 30°C (68 to 86°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front bumper cover excessively.


a.

Clean the front bumper cover surface.

i.

Using a heat light, heat the front bumper cover surface.


ii.

Remove any remaining double-sided tape from the front bumper cover.


iii.

Wipe off any tape adhesive residue with cleaner.



b.
B607482

Engage the 6 clips.


c.

Remove the release paper from a new hood to front end panel seal.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.
B607483C01
0,0 0,0 false
V100155

Double-sided Tape


Engage the guide and attach the double-sided tape as shown in the illustration to install the hood to front end panel seal.

HINT:

Press the hood to front end panel seal firmly to install it.



Hide 52128B 29.INSTALL FRONT BUMPER HOLE COVER LH (for Bar Type Radiator Grille)

a.
B607476C01
2.542,2.865 2.375,2.865 false 2.188,2.781 2.406,2.969 0.219,0.188 10 false *a
*a Hook
V113147

Install in this Direction


Engage the hook.


b.

Engage the 2 guides and 4 claws to install the front bumper hole cover LH as shown in the illustration.


Hide 52128B 30.INSTALL FRONT BUMPER HOLE COVER LH (for Mesh Type Radiator Grille)

a.
B607478C01
2.656,0.427 2.906,0.427 false 2.938,0.344 3.25,0.542 0.313,0.198 10 false *a
*a Hook
V113147

Install in this Direction


Engage the hook.


b.

Engage the 5 claws to install the front bumper hole cover LH as shown in the illustration.


Hide 52127D 31.INSTALL FRONT BUMPER HOLE COVER RH (for Mesh Type Radiator Grille)

HINT:

Use the same procedure as for the LH side.


Hide 32.INSTALL HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System)

a.

Engage the 7 clamps to install the headlight cleaner hose.

B607507


Hide 85208A 33.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

Hide 85207A 34.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:

Use the same procedure as for the LH side.


Hide 85354 35.INSTALL HEADLIGHT WASHER COVER LH (w/ Headlight Cleaner System)

Hide 85353 36.INSTALL HEADLIGHT WASHER COVER RH (w/ Headlight Cleaner System)

HINT:

Use the same procedure as for the LH side.


Hide 86790B 37.INSTALL FRONT TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)

Hide 52423A 38.INSTALL FRONT BUMPER PAD LH (for Bar Type Radiator Grille)

HINT:

When installing the front bumper pad LH, heat the front bumper cover using a heat light.


Heating Temperature
Item Temperature
Front Bumper Cover 20 to 30°C (68 to 86°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front bumper cover excessively.


a.

Clean the front bumper cover surface.

i.

Using a heat light, heat the front bumper cover surface.


ii.

Remove any remaining double-sided tape from the front bumper cover.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Remove the release paper from a new front bumper pad LH.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



c.
B608630C02
0.927,0.99 1.229,0.99 true 0.729,0.896 0.938,1.104 0.208,0.208 10 true *a
*a Line


Install the front bumper pad LH as shown in the illustration.

HINT:

Press the front bumper pad LH firmly to install it.



Hide 52422A 39.INSTALL FRONT BUMPER PAD RH (for Bar Type Radiator Grille)

HINT:

Use the same procedure as for the LH side.


Hide 52423A 40.INSTALL FRONT BUMPER PAD LH (for Mesh Type Radiator Grille)

a.
B607480

Engage the guide and 2 claws to install the front bumper pad LH.


Hide 52422A 41.INSTALL FRONT BUMPER PAD RH (for Mesh Type Radiator Grille)

HINT:

Use the same procedure as for the LH side.


Hide 52114A 42.INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET (for Bar Type Radiator Grille)

a.

w/ Bracket:

i.
B608148C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 claws as shown in the illustration.


ii.
B608146

Install the front bumper extension mounting bracket with the 2 screws.



Hide 52114A 43.INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET (for Mesh Type Radiator Grille)

a.
B608151C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 guides and 2 claws as shown in the illustration.


b.
B608149

Install the front bumper extension mounting bracket with the 2 screws.


Hide 88211B 44.INSTALL MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-collision System)

Hide 82114 45.INSTALL NO. 4 ENGINE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System)

a.

for Bar Type Radiator Grille:

i.

Engage the 7 clamps to install the No. 4 engine room wire.

B607467



b.

for Mesh Type Radiator Grille:

i.

Engage the 12 clamps to install the No. 4 engine room wire.

B607468



Hide 89347B 46.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 89341K 47.INSTALL FRONT CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 89347B 48.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 89341K 49.INSTALL FRONT CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 89341L 50.INSTALL FRONT CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)