Based on the driving conditions, the ECM regulates the volume of exhaust gas that is recirculated to each engine cylinder in order to lower the combustion temperature and reduce NOx emissions. The ECM monitors signals such as engine speed, engine coolant temperature, electric load, and vehicle speed. When the EGR permission conditions are met, the ECM controls the opening of the EGR valve linearly through signals to the EGR step motor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P04019C | Exhaust Gas Recirculation "A" Low / Insufficient Flow | Change in intake manifold pressure is small when the EGR valve opened and closed during fuel cut operation (2 trip detection logic). | ·
EGR valve assembly ·
EGR passage ·
EGR cooler assembly ·
Intake system ·
Manifold absolute pressure sensor |
Comes on | DTC stored | SAE Code: P0401 |
The ECM monitors the pressure inside the intake manifold while opening and closing the EGR valve during fuel cut operation. If there is no change in the manifold absolute pressure sensor value, the ECM interprets this as a malfunction of the EGR valve assembly, illuminates the MIL and stores this DTC.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].
Turn the GTS on.
Drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more [B].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Idle the engine for 30 seconds or more [C].
With the shift lever in M, accelerate the vehicle to 80 km/h (50 mph) or more [D].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Perform the fuel cut operation for 5 seconds or more, with the accelerator pedal fully released [E].
Repeat steps [D] through [E] above 3 times in one driving cycle.
Enter the following menus: Powertrain / Engine / Trouble Codes [F].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC P04019C.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system has a malfunction.
If the judgment result is INCOMPLETE, perform steps [D] through [F] again.
Refer to DTC P040318.
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>P040318
By using the Control the EGR Step Position Active Test, the operation of the EGR valve can be checked.
When the engine is idling steadily with the EGR valve fully closed, if the EGR valve is normal and it is opened using the Active Test, the Data List value changes as follows.
| Data List Item | Change in Data List when Number of Steps is Increased Using Control the EGR Step Position Active Test |
|---|---|
| Engine Speed | Idle becomes rough |
| Intake Manifold Absolute Pressure | Pressure rises |
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P04019C is output | A |
| DTC P04019C and other DTCs are output | B |
If any DTCs other than P04019C are output, troubleshoot those DTCs first.
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Intake Manifold Absolute Pressure.
| Tester Display |
|---|
| Intake Manifold Absolute Pressure |
Read the value of Intake Manifold Absolute Pressure.
| GTS Display | Specified Condition |
|---|---|
| Intake Manifold Absolute Pressure | 80 to 110 kPa (11.6 to 15.95 psi) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.
The A/C switch and all accessories should be off.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position / Data List / Intake Manifold Absolute Pressure and Coolant Temperature.
| Active Test Display |
|---|
| Control the EGR Step Position |
| Data List Display |
|---|
| Intake Manifold Absolute Pressure |
| Coolant Temperature |
According to the display on the GTS, compare the values of Data List item Intake Manifold Absolute Pressure before and while performing the Active Test.
Do not leave the EGR valve open for 10 seconds or more during the Active Test.
Be sure to return the EGR valve to step 0 when the Active Test is completed.
Do not open the EGR valve 30 steps or more during the Active Test.
The value of Intake Manifold Absolute Pressure changes according to the EGR valve step set by the Active Test.
| Data List | Control the EGR Step Position (Active Test) | ||
|---|---|---|---|
| Before Active Test
(Engine idling) |
0 Steps | 0 to 30 Steps
(Engine idling) |
|
| Intake Manifold Absolute Pressure | 18 to 38 kPa (2.6 to 5.5 psi) | 18 to 38 kPa (2.6 to 5.5 psi)
(EGR valve is fully closed) |
Intake Manifold Absolute Pressure value is at least +10 kPa (1.45 psi) higher than when EGR valve is fully closed |
While performing the Active Test, if the increase in the value of Intake Manifold Absolute Pressure is small, the EGR valve assembly may be malfunctioning.
| Result | Proceed to |
|---|---|
| Before performing the Active Test (while the engine is idling), the value of Intake Manifold Absolute Pressure is not between 18 to 38 kPa (2.6 to 5.5 psi). | A |
| When performing the Active Test to change the EGR valve step between 0 (EGR valve fully closed) and 30, the value of Intake Manifold Absolute Pressure changes less than 10 kPa (1.42 psi). | B |
| Other than above | C |
A
B
C
Check the intake system for vacuum leaks.
Click hereEngine / Hybrid System>M20A-FKS (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION
No leaks from intake system.
Perform "Inspection After Repair" after repairing or replacing the intake system.
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the EGR valve assembly.
Click hereEngine / Hybrid System>M20A-FKS (EMISSION CONTROL)>EGR VALVE>REMOVAL
Check if the EGR valve is stuck open.
EGR valve is tightly closed.
Perform "Inspection After Repair" after replacing the EGR valve assembly.
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the EGR valve assembly.
Click hereEngine / Hybrid System>M20A-FKS (EMISSION CONTROL)>EGR VALVE>REMOVAL
Perform "Inspection After Repair" after replacing the EGR valve assembly.
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P04019C is output | B |
A
B
Replace the EGR cooler assembly.
Click hereEngine / Hybrid System>M20A-FKS (EMISSION CONTROL)>EGR COOLER>REMOVAL
If any of the EGR system related pipes (EGR pipe, exhaust manifold, etc.) are cracked, damaged or clogged, replace them as necessary.
Perform "Inspection After Repair" after replacing the exhaust system.
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
DTCs are not output.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P04019C is output | B |
Perform "Inspection After Repair" after replacing the EGR valve assembly.
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
A
B