Home › Engine / Hybrid System › M20A-FKS (ENGINE CONTROL) › SFI SYSTEM › from 2021.02
RM33A0E _51 Engine / Hybrid System _098626 M20A-FKS ENGINE CONTROL _0466473 SFI SYSTEM C

M20A-FKS ENGINE CONTROL  SFI SYSTEM  U010187  Lost Communication with TCM Missing Message  


MONITOR DESCRIPTION

The Transmission Control Module (TCM) and ECM perform 2-way communication with each other via the Controller Area Network (CAN). The TCM sends signals to the ECM concerning required engine speed, required engine torque, warning indicators in the combination meter assembly, DTCs and other data. The ECM sends signals to the TCM concerning engine speed, opening angle of the throttle valve, temperature of intake air, temperature of engine coolant, engine torque and other data. If the TCM cannot communicate with the ECM, the TCM will conclude that there is a malfunction in the CAN communication system, illuminate the MIL and store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
U010187 Lost Communication with TCM Missing Message All of the following conditions are met for 1.25 seconds or more (1 trip detection logic):
·

Ignition switch ON

·

Battery voltage is 10 V or higher

·

No communication between engine control unit and transmission control unit


ECM Comes on DTC stored SAE Code: U0101

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Wait 5 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: U010187.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A445237E12
0.833,0.594 1.292,0.792 0.458,0.198 10 false CAN- 6.01,0.625 6.563,0.854 0.552,0.229 10 false CANN 0.844,1.031 1.302,1.229 0.458,0.198 10 false CAN+ 6.01,1.031 6.563,1.24 0.552,0.208 10 false CANP 0.833,1.552 1.563,1.792 0.729,0.24 10 false IGSW 1.042,2.469 1.5,2.667 0.458,0.198 10 false E1 1.313,0.448 1.771,0.646 0.458,0.198 10 false 17 1.333,0.875 1.792,1.073 0.458,0.198 10 false 18 1.313,2.354 1.771,2.552 0.458,0.198 10 false 2 5.792,0.885 6.25,1.083 0.458,0.198 10 false 7 5.708,0.448 6.167,0.646 0.458,0.198 10 false 17 3.688,1.99 5.823,2.448 2.135,0.458 10 false from EFI-MAIN NO. 1 Relay 2.865,3.156 5.156,3.458 2.292,0.302 10 false : CAN Communication Line 0.49,2.885 1.031,3.125 0.542,0.24 10 false C111 0.906,2.885 1.354,3.188 0.448,0.302 10 false TCM 2.521,2.135 3.365,2.49 0.844,0.354 10 false EFI NO. 1 6.323,2.885 6.802,3.167 0.479,0.281 10 false ECM 5.99,2.885 6.448,3.083 0.458,0.198 10 false A24 1.01,2 1.469,2.198 0.458,0.198 10 false +B 1.313,1.906 1.771,2.104 0.458,0.198 10 false 1 1.292,1.469 1.75,1.667 0.458,0.198 10 false 41 1.708,1.688 2.969,2.042 1.26,0.354 10 false ECU-IG2 NO. 1 3.021,1.542 4.667,1.885 1.646,0.344 10 false from IG2 NO. 1 Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC U010187)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Read the DTCs.

Result:
Result Proceed to
DTC U010187 is output A
DTC U010187 and other DTCs are output B


HINT:

If any DTCs other than U010187 are output, troubleshoot those DTCs first.




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF TCM)

B

GO TO DTC CHART

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF TCM)
A435803C22
0.125,1 0.521,1.24 0.396,0.24 1.823,1.802 1.365,1.063 true 0.656,1.76 1.219,1.073 true 2.375,1.823 1.833,1.188 true 0.167,1.042 0.656,1.333 0.49,0.292 10 false C111 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 0.531,1.792 0.844,1.99 0.313,0.198 10 false +B 1.792,1.823 2.104,2.021 0.313,0.198 10 false E1 2.281,1.854 2.969,2.083 0.688,0.229 10 false IGSW
*a Front view of wire harness connector
(to TCM)


a.

Disconnect the TCM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C111-1 (+B) - C111-2 (E1) Ignition switch ON 11 to 14 V
C111-41 (IGSW) - C111-2 (E1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TCM - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (TCM - ECM)
a.

Disconnect the TCM connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C111-18 (CAN+) - A24 -7 (CANP) Always Below 1 Ω
C111-17 (CAN-) - A24 -17 (CANN) Always Below 1 Ω
C111-18 (CAN+) or A24 -7 (CANP) - Body ground and other terminals Always 10 kΩ or higher
C111-17 (CAN-) or A24 -17 (CANN) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE TCM
a.

Replace the TCM.

Click hereDrivetrain>K120 (CVT)>TCM>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC U010187)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC U010187)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes.


c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC U010187 is output B




A

END

B