Home › Engine / Hybrid System › M20A-FKS (ENGINE CONTROL) › SFI SYSTEM › from 2021.02
RM33A0E _51 Engine / Hybrid System _098626 M20A-FKS ENGINE CONTROL _0466473 SFI SYSTEM J

M20A-FKS ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B, +B2 (BATT) terminals to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A256646E92
0.979,0.833 3.021,1.104 2.042,0.271 10 false from EFI-MAIN NO. 4 Fuse 0.927,1.177 3.042,1.427 2.115,0.25 10 false from EFI-MAIN NO. 1 Relay 0.135,1.969 2.625,2.469 2.49,0.5 10 false to Throttle Position Sensor, Accelerator Pedal Sensor Assembly, etc. (Sensors which have an IC) 0.135,2.646 2.563,3.031 2.427,0.385 10 false to Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.969,3.094 5.313,3.406 0.344,0.313 10 false ECM 2.885,0.677 3.563,1 0.677,0.323 10 false BATT 2.823,1.042 3.49,1.292 0.667,0.25 10 false +B, +B2 3.063,2.021 3.427,2.25 0.365,0.229 10 false VC 4.396,0.875 6.188,1.229 1.792,0.354 10 false 5 V Constant Voltage Circuit 5.365,1.76 6.354,2.115 0.99,0.354 10 false Microprocessor 4.073,2.844 4.333,3.063 0.26,0.219 10 false R

When the VC circuit has a short circuit, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. When the system is in this condition, it will not start.

WIRING DIAGRAM

·

For the circuit diagram of the ECM power source refer to the ECM power source circuit.

Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>ECM Power Source Circuit

·

VC Output Circuit

A447608E10
0.229,2.781 0.688,2.979 0.458,0.198 10 false d5 0.219,0.677 1.802,1.438 1.583,0.76 10 false Throttle Body with Motor Assembly 0.219,2.979 2.021,3.417 1.802,0.438 10 false Crankshaft Position Sensor 0.219,4.635 1.854,5.146 1.635,0.51 10 false Camshaft Position Sensor (for Intake Camshaft) 0.219,4.458 0.677,4.656 0.458,0.198 10 false C18 0.219,6.333 1.865,6.906 1.646,0.573 10 false Camshaft Position Sensor (for Exhaust Camshaft) 0.219,0.5 0.677,0.698 0.458,0.198 10 false C27 2.563,0.573 3.021,0.771 0.458,0.198 10 false VC 2.583,1.135 3.042,1.333 0.458,0.198 10 false E2 2.427,2.219 2.885,2.417 0.458,0.198 10 false VTA2 2.479,1.667 2.938,1.865 0.458,0.198 10 false VTA 2.396,2.875 2.854,3.073 0.458,0.198 10 false VCNE 2.5,3.385 2.958,3.583 0.458,0.198 10 false NE- 2.49,3.917 2.948,4.115 0.458,0.198 10 false NE+ 2.563,4.542 3.021,4.74 0.458,0.198 10 false VC 2.479,5.063 2.938,5.26 0.458,0.198 10 false VVI- 2.458,5.615 2.917,5.813 0.458,0.198 10 false VVI+ 2.49,6.281 2.948,6.479 0.458,0.198 10 false VC2 2.427,6.792 2.885,6.99 0.458,0.198 10 false VVE- 2.396,7.354 2.854,7.552 0.458,0.198 10 false VVE+ 6.26,0.417 6.719,0.615 0.458,0.198 10 false 5 V 5.271,0.49 5.729,0.688 0.458,0.198 10 false VCTA 5.292,1.031 5.75,1.229 0.458,0.198 10 false ETA 5.281,1.677 5.74,1.875 0.458,0.198 10 false VTA1 5.271,2.198 5.729,2.396 0.458,0.198 10 false VTA2 5.281,2.771 5.74,2.969 0.458,0.198 10 false VCNE 5.292,3.302 5.75,3.5 0.458,0.198 10 false NE- 5.271,3.948 5.729,4.146 0.458,0.198 10 false NE+ 5.271,4.448 5.729,4.646 0.458,0.198 10 false VCV1 5.281,4.969 5.74,5.167 0.458,0.198 10 false VV1- 5.271,5.625 5.729,5.823 0.458,0.198 10 false VV1+ 5.271,6.177 5.729,6.375 0.458,0.198 10 false VCE1 5.26,6.698 5.719,6.896 0.458,0.198 10 false EV1- 5.271,7.344 5.729,7.542 0.458,0.198 10 false EV1+ 5.833,8.135 6.292,8.333 0.458,0.198 10 false ECM 2.865,0.51 3.323,0.708 0.458,0.198 10 false 2 2.854,1.01 3.313,1.208 0.458,0.198 10 false 4 2.854,1.573 3.313,1.771 0.458,0.198 10 false 1 2.854,2.094 3.313,2.292 0.458,0.198 10 false 3 2.865,2.781 3.323,2.979 0.458,0.198 10 false 3 2.865,3.281 3.323,3.479 0.458,0.198 10 false 2 2.854,3.833 3.313,4.031 0.458,0.198 10 false 1 2.854,4.458 3.313,4.656 0.458,0.198 10 false 3 2.844,4.979 3.302,5.177 0.458,0.198 10 false 2 2.844,5.51 3.302,5.708 0.458,0.198 10 false 1 2.844,6.177 3.302,6.375 0.458,0.198 10 false 3 2.833,6.708 3.292,6.906 0.458,0.198 10 false 2 2.833,7.24 3.292,7.438 0.458,0.198 10 false 1 0.229,6.167 0.688,6.365 0.458,0.198 10 false C77 4.885,0.417 5.344,0.615 0.458,0.198 10 false 109 4.896,0.958 5.354,1.156 0.458,0.198 10 false 110 4.896,1.5 5.354,1.698 0.458,0.198 10 false 108 4.938,2.031 5.396,2.229 0.458,0.198 10 false 87 4.896,2.708 5.354,2.906 0.458,0.198 10 false 116 4.896,3.229 5.354,3.427 0.458,0.198 10 false 115 4.948,3.781 5.406,3.979 0.458,0.198 10 false 93 4.927,4.385 5.385,4.583 0.458,0.198 10 false 88 4.927,4.896 5.385,5.094 0.458,0.198 10 false 89 4.938,5.448 5.396,5.646 0.458,0.198 10 false 90 4.875,6.115 5.333,6.313 0.458,0.198 10 false 113 4.896,6.635 5.354,6.833 0.458,0.198 10 false 114 4.917,7.177 5.375,7.375 0.458,0.198 10 false 91 4.896,0.604 5.604,0.823 0.708,0.219 10 false C57 4.896,1.135 5.604,1.354 0.708,0.219 10 false C57 4.896,1.677 5.604,1.896 0.708,0.219 10 false C57 4.896,2.219 5.604,2.438 0.708,0.219 10 false C57 4.896,2.885 5.604,3.104 0.708,0.219 10 false C57 4.896,3.406 5.604,3.625 0.708,0.219 10 false C57 4.896,3.948 5.604,4.167 0.708,0.219 10 false C57 4.896,4.563 5.604,4.781 0.708,0.219 10 false C57 4.896,5.083 5.604,5.302 0.708,0.219 10 false C57 4.896,5.625 5.604,5.844 0.708,0.219 10 false C57 4.885,6.292 5.594,6.51 0.708,0.219 10 false C57 4.885,6.813 5.594,7.031 0.708,0.219 10 false C57 4.885,7.354 5.594,7.573 0.708,0.219 10 false C57

A447609E12
0.219,4.948 1.813,5.469 1.594,0.521 10 false Accelerator Pedal Sensor Assembly 0.219,4.75 1.792,5.021 1.573,0.271 10 false A20 2.406,4.823 3.052,5.125 0.646,0.302 10 false VCPA 2.427,5.271 3.073,5.573 0.646,0.302 10 false VCP2 2.5,5.729 3.146,6.031 0.646,0.302 10 false EPA 2.417,6.156 3.063,6.458 0.646,0.302 10 false EPA2 2.49,6.604 3.135,6.906 0.646,0.302 10 false VPA 2.427,7.073 3.073,7.375 0.646,0.302 10 false VPA2 4.917,4.833 5.563,5.135 0.646,0.302 10 false A24 5.302,4.729 5.948,5.031 0.646,0.302 10 false VCPA 5.292,5.177 5.938,5.479 0.646,0.302 10 false VCP2 5.292,5.625 5.938,5.927 0.646,0.302 10 false EPA 5.302,6.083 5.948,6.385 0.646,0.302 10 false EPA2 5.313,6.625 5.958,6.927 0.646,0.302 10 false VPA 5.302,7.073 5.948,7.375 0.646,0.302 10 false VPA2 4.969,4.646 5.615,4.948 0.646,0.302 10 false 57 4.958,5.094 5.604,5.396 0.646,0.302 10 false 60 4.958,5.542 5.604,5.844 0.646,0.302 10 false 56 4.958,5.99 5.604,6.292 0.646,0.302 10 false 59 4.969,6.427 5.615,6.729 0.646,0.302 10 false 55 4.969,6.885 5.615,7.188 0.646,0.302 10 false 58 5.781,7.74 6.417,8 0.635,0.26 10 false ECM 0.24,2.656 2.063,3.292 1.823,0.635 10 false Oil Pressure and Temperature Sensor 0.24,2.448 1.813,2.719 1.573,0.271 10 false C110 2.573,2.521 2.885,2.719 0.313,0.198 10 false VC 2.427,4.042 3.042,4.24 0.615,0.198 10 false TOUT 2.406,3.542 3.021,3.74 0.615,0.198 10 false POUT 2.479,3.01 2.875,3.229 0.396,0.219 10 false GND 5.302,2.417 5.917,2.615 0.615,0.198 10 false VCPE 5.302,4.042 5.917,4.24 0.615,0.198 10 false THEO 5.302,3.531 5.76,3.729 0.458,0.198 10 false PEO 5.302,2.917 5.917,3.115 0.615,0.198 10 false EPEO 2.875,5.177 3.031,5.375 0.156,0.198 10 false 1 2.885,6.083 3.042,6.281 0.156,0.198 10 false 2 2.875,6.979 3.031,7.177 0.156,0.198 10 false 3 2.896,4.74 3.052,4.938 0.156,0.198 10 false 4 2.885,5.635 3.042,5.833 0.156,0.198 10 false 5 2.875,6.531 3.031,6.729 0.156,0.198 10 false 6 2.885,2.438 3.042,2.635 0.156,0.198 10 false 3 2.885,2.938 3.042,3.135 0.156,0.198 10 false 2 2.875,3.448 3.031,3.646 0.156,0.198 10 false 1 2.875,3.958 3.031,4.156 0.156,0.198 10 false 4 4.917,5.281 5.563,5.583 0.646,0.302 10 false A24 4.917,5.729 5.563,6.031 0.646,0.302 10 false A24 4.917,6.177 5.563,6.479 0.646,0.302 10 false A24 4.927,6.615 5.573,6.917 0.646,0.302 10 false A24 4.927,7.063 5.573,7.365 0.646,0.302 10 false A24 4.917,2.521 5.563,2.823 0.646,0.302 10 false C57 4.917,3.021 5.563,3.323 0.646,0.302 10 false C57 4.917,3.542 5.563,3.844 0.646,0.302 10 false C57 4.917,4.042 5.563,4.344 0.646,0.302 10 false C57 4.958,2.344 5.271,2.542 0.313,0.198 10 false 99 4.917,2.833 5.375,3.031 0.458,0.198 10 false 100 4.917,3.354 5.375,3.552 0.458,0.198 10 false 122 4.917,3.865 5.375,4.063 0.458,0.198 10 false 123 4.927,0.698 5.573,1 0.646,0.302 10 false C57 4.927,1.188 5.573,1.49 0.646,0.302 10 false C57 4.917,1.677 5.563,1.979 0.646,0.302 10 false C57 0.271,0.781 2.104,1.24 1.833,0.458 10 false Manifold Absolute Pressure Sensor 0.26,0.604 0.719,0.802 0.458,0.198 10 false C28 2.594,0.698 2.906,0.896 0.313,0.198 10 false VC 2.625,1.188 2.938,1.385 0.313,0.198 10 false E2 2.542,1.688 3,1.885 0.458,0.198 10 false PIM 2.875,0.604 3.031,0.802 0.156,0.198 10 false 3 2.875,1.083 3.031,1.281 0.156,0.198 10 false 1 2.875,1.573 3.031,1.771 0.156,0.198 10 false 2 5.302,0.594 5.917,0.792 0.615,0.198 10 false VCPM 5.302,1.083 5.917,1.281 0.615,0.198 10 false EPIM 5.302,1.667 5.76,1.865 0.458,0.198 10 false PIM 4.927,0.51 5.385,0.708 0.458,0.198 10 false 121 4.917,1.01 5.375,1.208 0.458,0.198 10 false 119 4.938,1.5 5.396,1.698 0.458,0.198 10 false 120

A486628E01
0.344,0.927 0.802,1.125 0.458,0.198 10 false C30 0.344,1.125 1.698,2.021 1.354,0.896 10 false Mass Air Flow Meter Sub-assembly 2.573,0.865 3.031,1.063 0.458,0.198 10 false 5V 2.5,1.448 2.958,1.646 0.458,0.198 10 false E2G 2.563,2.052 3.021,2.25 0.458,0.198 10 false FG 2.5,2.635 2.958,2.833 0.458,0.198 10 false THA 2.896,0.75 3.354,0.948 0.458,0.198 10 false 3 2.906,1.333 3.365,1.531 0.458,0.198 10 false 2 2.896,1.938 3.354,2.135 0.458,0.198 10 false 1 2.906,2.51 3.365,2.708 0.458,0.198 10 false 4 4.917,0.875 5.344,1.042 0.427,0.167 10 false C57 4.917,1.448 5.344,1.615 0.427,0.167 10 false C57 4.917,2.052 5.344,2.219 0.427,0.167 10 false C57 4.917,2.646 5.344,2.813 0.427,0.167 10 false C57 5,0.688 5.458,0.885 0.458,0.198 10 false 78 4.979,1.25 5.438,1.448 0.458,0.198 10 false 79 4.938,1.844 5.396,2.042 0.458,0.198 10 false 101 4.938,2.438 5.396,2.635 0.458,0.198 10 false 102 5.323,0.74 5.75,0.906 0.427,0.167 10 false VCVG 5.323,1.313 5.75,1.479 0.427,0.167 10 false E2G 5.323,2.052 5.75,2.219 0.427,0.167 10 false VG 5.313,2.625 5.74,2.792 0.427,0.167 10 false THA 0.333,3.813 0.792,4.01 0.458,0.198 10 false d3 0.333,4.021 2.24,4.781 1.906,0.76 10 false Fuel Pressure Sensor (for High Pressure Side) 2.573,3.792 3.031,3.99 0.458,0.198 10 false VC 2.594,4.354 3.052,4.552 0.458,0.198 10 false E2 2.573,4.844 3.031,5.042 0.458,0.198 10 false PR 2.906,3.615 3.365,3.813 0.458,0.198 10 false 1 2.896,4.198 3.354,4.396 0.458,0.198 10 false 2 2.896,4.708 3.354,4.906 0.458,0.198 10 false 3 4.906,3.771 5.333,3.938 0.427,0.167 10 false C57 4.906,4.344 5.333,4.51 0.427,0.167 10 false C57 4.906,4.833 5.333,5 0.427,0.167 10 false C57 5.323,3.604 5.75,3.771 0.427,0.167 10 false VCPR 5.323,4.198 5.75,4.365 0.427,0.167 10 false EPR 5.323,4.833 5.75,5 0.427,0.167 10 false PR 4.948,3.542 5.406,3.74 0.458,0.198 10 false 98 4.948,4.135 5.406,4.333 0.458,0.198 10 false 96 4.948,4.625 5.406,4.823 0.458,0.198 10 false 97 0.344,6.052 0.802,6.25 0.458,0.198 10 false F12 0.323,6.229 2.063,6.854 1.74,0.625 10 false No. 2 Fuel Pressure Sensor (for Low Pressure Side) 2.583,5.99 3.042,6.188 0.458,0.198 10 false VC 2.604,6.552 3.063,6.75 0.458,0.198 10 false E2 2.521,7.146 2.979,7.344 0.458,0.198 10 false PFL 2.906,5.813 3.365,6.01 0.458,0.198 10 false 1 2.927,6.417 3.385,6.615 0.458,0.198 10 false 3 2.917,6.99 3.375,7.188 0.458,0.198 10 false 2 4.917,5.979 5.344,6.146 0.427,0.167 10 false C57 4.917,6.552 5.344,6.719 0.427,0.167 10 false C57 4.917,7.125 5.344,7.292 0.427,0.167 10 false C57 4.969,5.76 5.427,5.958 0.458,0.198 10 false 84 4.969,6.344 5.427,6.542 0.458,0.198 10 false 61 4.938,6.927 5.396,7.125 0.458,0.198 10 false 107 5.344,5.833 5.771,6 0.427,0.167 10 false VCPF 5.313,6.396 5.74,6.563 0.427,0.167 10 false EPFL 5.333,7.115 5.76,7.281 0.427,0.167 10 false PFL 5.813,7.99 6.583,8.385 0.771,0.396 10 false ECM


CAUTION / NOTICE / HINT

NOTICE:

Check the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

2.CHECK EFI NO. 1 FUSE VOLTAGE

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK EFI NO. 1 FUSE VOLTAGE
A402426C05
2.083,0.76 2.698,0.292 true 0.156,0.208 0.469,0.406 0.313,0.198 10 false *1 2.729,0.188 3.042,0.385 0.313,0.198 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 EFI NO. 1 Fuse


a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
1 (EFI NO. 1 fuse) - Body ground Ignition switch ON 11 to 14 V


HINT:
·

Check the fuse with it installed to the engine room relay block and junction block assembly.

·

If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.




Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)

NG

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle body with motor assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



A

4.CHECK CONNECTION BETWEEN GTS AND ECM (CRANKSHAFT POSITION SENSOR)

B

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

4.CHECK CONNECTION BETWEEN GTS AND ECM (CRANKSHAFT POSITION SENSOR)
a.

Disconnect the crankshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

5.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))

B

5.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))
a.

Disconnect the camshaft position sensor (for intake camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

6.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))

B

REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

6.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))
a.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

7.CHECK CONNECTION BETWEEN GTS AND ECM (MANIFOLD ABSOLUTE PRESSURE SENSOR)

B

REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

7.CHECK CONNECTION BETWEEN GTS AND ECM (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

8.CHECK CONNECTION BETWEEN GTS AND ECM (OIL PRESSURE AND TEMPERATURE SENSOR)

B

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

8.CHECK CONNECTION BETWEEN GTS AND ECM (OIL PRESSURE AND TEMPERATURE SENSOR)
a.

Disconnect the oil pressure and temperature sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

9.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)

B

9.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

10.CHECK CONNECTION BETWEEN GTS AND ECM (MASS AIR FLOW METER SUB-ASSEMBLY)

B

REPLACE ACCELERATOR PEDAL(W/SENSOR) ROD ASSEMBLY

10.CHECK CONNECTION BETWEEN GTS AND ECM (MASS AIR FLOW METER SUB-ASSEMBLY)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



A

11.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE))

B

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

11.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE))
a.

Disconnect the fuel pressure sensor (for high pressure side) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the fuel pressure sensor (for high pressure side).

Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



A

12.CHECK CONNECTION BETWEEN GTS AND ECM (NO. 2 FUEL PRESSURE SENSOR (FOR LOW PRESSURE SIDE))

B

REPLACE FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE)

12.CHECK CONNECTION BETWEEN GTS AND ECM (NO. 2 FUEL PRESSURE SENSOR (FOR LOW PRESSURE SIDE))
a.

Disconnect the No. 2 fuel pressure sensor (for low pressure side) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the No. 2 fuel pressure sensor (for low pressure side).

Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



A

13.CHECK HARNESS AND CONNECTOR

B

REPLACE NO. 2 FUEL PRESSURE SENSOR (FOR LOW PRESSURE SIDE)

13.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the crankshaft position sensor connector.


c.

Disconnect the camshaft position sensor (for intake camshaft) connector.


d.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


e.

Disconnect the manifold absolute pressure sensor connector.


f.

Disconnect the oil pressure and temperature sensor connector.


g.

Disconnect the accelerator pedal sensor assembly connector.


h.

Disconnect the mass air flow meter sub-assembly connector.


i.

Disconnect the fuel pressure sensor (for high pressure side) connector.


j.

Disconnect the No. 2 fuel pressure sensor (for low pressure side) connector.


k.

Disconnect the ECM connectors.


l.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C57-109 (VCTA) - Body ground Always 10 kΩ or higher
C57-116 (VCNE) - Body ground Always 10 kΩ or higher
C57-88 (VCV1) - Body ground Always 10 kΩ or higher
C57-113 (VCE1) - Body ground Always 10 kΩ or higher
C57-121 (VCPM) - Body ground Always 10 kΩ or higher
C57-99 (VCPE) - Body ground Always 10 kΩ or higher
A24-57 (VCPA) - Body ground Always 10 kΩ or higher
A24-60 (VCP2) - Body ground Always 10 kΩ or higher
C57-78 (VCVG) - Body ground Always 10 kΩ or higher
C57-98 (VCPR) - Body ground Always 10 kΩ or higher
C57-84 (VCPF) - Body ground Always 10 kΩ or higher



m.

Remove the EFI-MAIN NO. 2, VVT and EFI-MAIN NO. 3 relays from the engine room relay block and junction block assembly.

HINT:

Remove the EFI-MAIN NO. 2, VVT and EFI-MAIN NO. 3 relays connected between the checked terminals as the coil inside the relay influences the measurement value.



n.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-9 (+B) - 1 (EFI NO. 1 fuse) Always Below 1 Ω
A24-35 (+B2) - 1 (EFI NO. 1 fuse) Always Below 1 Ω
A24-9 (+B) - Body ground Always 10 kΩ or higher
A24-35 (+B2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR