Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2021.02
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0351447 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1621  Back Camera Power Supply Failure  


DESCRIPTION

This DTC is stored if the rear television camera assembly judges as a result of its self check that the signals or signal lines between the rear television camera assembly and television camera controller are not normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1621 Back Camera Power Supply Failure Rear television camera assembly power supply failure
·

Harness or connector

·

Rear television camera assembly

·

Television camera controller



WIRING DIAGRAM

E453847E08
0.521,2.906 2.677,3.344 2.156,0.438 10 false Rear Television Camera Assembly 0.521,2.729 0.969,2.99 0.448,0.26 10 false m4 5.427,2.906 6.99,3.26 1.563,0.354 10 false Television Camera Assembly Connector 5.25,2.729 5.688,3.052 0.438,0.323 10 false R126 2.885,0.74 3.635,1.094 0.75,0.354 10 false ECU-ACC 4.625,0.552 6.208,1.01 1.583,0.458 10 false from ACC Relay 1.604,0.583 2.104,0.885 0.5,0.302 10 false CB+ 1.969,0.448 2.469,0.75 0.5,0.302 10 false 6 1.979,2.188 2.479,2.49 0.5,0.302 10 false 5 1.479,2.323 1.979,2.625 0.5,0.302 10 false CGND 5.417,2.188 6.083,2.5 0.667,0.313 10 false 32 5.688,2.323 6.333,2.604 0.646,0.281 10 false CGND

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ACC POWER SUPPLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the m4 rear television camera assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
m4-6 (CB+) - Body ground Ignition switch on (ACC) 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - REAR TELEVISION CAMERA ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the R126 television camera controller connector.


b.

Disconnect the m4 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R126-32 (CGND) - m4-5 (CGND) Always Below 1 Ω
R126-32 (CGND) or m4-5 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK TELEVISION CAMERA CONTROLLER (CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TELEVISION CAMERA CONTROLLER (CGND)
a.
E407111C66
1.417,0.25 1.917,0.5 0.5,0.25 1.51,1.156 1.979,1.948 1.979,1.948 2.229,1.948 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 1.479,0.292 1.979,0.448 0.5,0.156 10 false R126 2.271,1.865 2.833,2.052 0.563,0.188 10 false CGND
*a Component with harness connected
(Television Camera Controller)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R126-32 (CGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG