DTC C1622 is stored if the television camera controller judges as a result of its self check that the signals or signal lines between the television camera controller and rear television camera assembly are not normal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1622 | Open or Short Circuit in Back Camera Signal | Open or short in the rear television camera signal circuit | ·
Harness or connector ·
Rear television camera assembly ·
Television camera controller |
When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION
Inspect the fuses for circuits related to this system before performing the following procedure.
Disconnect the m4 rear television camera assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| m4-6 (CB+) - Body ground | Ignition switch on (ACC) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the R126 television camera controller connector.
Disconnect the m4 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R126-29 (CV+) - m4-3 (CV+) | Always | Below 1 Ω |
| R126-30 (CV-) - m4-2 (CV-) | Always | Below 1 Ω |
| R126-32 (CGND) - m4-5 (CGND) | Always | Below 1 Ω |
| R126-29 (CV+) or m4-3 (CV+) - Body ground | Always | 10 kΩ or higher |
| R126-30 (CV-) or m4-2 (CV-) - Body ground | Always | 10 kΩ or higher |
| R126-32 (CGND) or m4-5 (CGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the R126 television camera controller connector.
| *a | Component without harness connected
(Television Camera Controller) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 30 (CV-) - Body ground | Always | Below 1 Ω |
| 32 (CGND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Television Camera Controller) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R126-32 (CGND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the television camera controller with the connector still connected.
Using an oscilloscope, check the waveform of the rear television camera assembly.
A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the television camera controller with the connector connected.
| *a | Component with harness connected
(Television Camera Controller) |
*b | Waveform 1 (camera lens not covered, displaying an image) |
| *c | Waveform 2 (camera lens covered, blacking out the screen) | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
The video waveform changes according to the image sent by the rear television camera assembly.
The video waveform is constantly output when the ignition switch is turned to ACC.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | R126-29 (CV+) - R126-32 (CGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Ignition switch ON, panoramic view monitor system operating |
Waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG