Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2021.02
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0351447 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1681  Front Camera Feedback Malfunction  


DESCRIPTION

DTC C1681 is stored if the television camera controller judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the front television camera assembly to the television camera controller.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1681 Front Camera Feedback Malfunction Front television camera power supply failure
·

Harness or connector

·

Front television camera assembly

·

Television camera controller



WIRING DIAGRAM

E372776E27
1.74,0.615 2.656,0.813 0.917,0.198 10 false BCB+ 1.771,0.99 2.688,1.188 0.917,0.198 10 false BCV- 1.74,1.406 2.656,1.604 0.917,0.198 10 false BCV+ 1.729,1.813 2.646,2.01 0.917,0.198 10 false BGND 0.583,2.625 1.5,2.823 0.917,0.198 10 false B7 0.583,2.792 3.354,3.083 2.771,0.292 10 false Front Television Camera Assembly 3.521,2 3.896,2.219 0.375,0.219 10 false * 2.219,0.49 2.594,0.708 0.375,0.219 10 false 6 2.219,0.885 2.594,1.104 0.375,0.219 10 false 2 2.208,1.271 2.583,1.49 0.375,0.219 10 false 3 2.208,1.677 2.583,1.896 0.375,0.219 10 false 5 4.75,0.5 5.125,0.719 0.375,0.219 10 false 15 4.75,0.896 5.125,1.115 0.375,0.219 10 false 13 4.76,1.313 5.135,1.531 0.375,0.219 10 false 36 4.76,1.698 5.135,1.917 0.375,0.219 10 false 37 4.76,2.094 5.135,2.313 0.375,0.219 10 false 14 4.708,2.635 5.167,2.885 0.458,0.25 10 false R126 4.708,2.813 6.719,3.198 2.01,0.385 10 false Television Camera Controller 5.021,0.615 5.938,0.813 0.917,0.198 10 false BCB+ 5.021,1.01 5.938,1.208 0.917,0.198 10 false BCV- 5.01,1.406 5.927,1.604 0.917,0.198 10 false BCV+ 5.01,1.802 5.927,2 0.917,0.198 10 false BGND 5.01,2.208 5.927,2.406 0.917,0.198 10 false SGND 3.792,3.292 4.708,3.49 0.917,0.198 10 false *: Shielded

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - FRONT TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the R126 television camera controller connector.


b.

Disconnect the B7 front television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R126-15 (BCB+) - B7-6 (BCB+) Always Below 1 Ω
R126-36 (BCV+) - B7-3 (BCV+) Always Below 1 Ω
R126-13 (BCV-) - B7-2 (BCV-) Always Below 1 Ω
R126-37 (BGND) - B7-5 (BGND) Always Below 1 Ω
R126-14 (SGND) - Body ground Always 10 kΩ or higher
R126-15 (BCB+) or B7-6 (BCB+) - Body ground Always 10 kΩ or higher
R126-36 (BCV+) or B7-3 (BCV+) - Body ground Always 10 kΩ or higher
R126-13 (BCV-) or B7-2 (BCV-) - Body ground Always 10 kΩ or higher
R126-37 (BGND) or B7-5 (BGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK TELEVISION CAMERA CONTROLLER (BCV-, BGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TELEVISION CAMERA CONTROLLER (BCV-, BGND)
a.

Disconnect the R126 television camera controller connector.


b.
E330226C49
0.76,1.792 0.927,1.792 0.927,1.792 1.073,1.146 true 0.844,0.438 1.01,0.438 1.01,0.438 1.177,0.99 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 0.333,1.698 0.833,1.854 0.5,0.156 10 false BGND 0.427,0.354 0.927,0.51 0.5,0.156 10 false BCV-
*a Component without harness connected
(Television Camera Controller)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
37 (BGND) - Body ground Always Below 1 Ω
13 (BCV-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK TELEVISION CAMERA CONTROLLER (BCB+, BGND)

NG

3.CHECK TELEVISION CAMERA CONTROLLER (BCB+, BGND)
a.
E402272C29
1.417,0.25 1.917,0.5 0.5,0.25 0.5,1.771 0.677,1.771 0.677,1.771 1.094,1.156 true 0.667,0.333 0.833,0.333 0.833,0.333 1.063,0.99 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 0.302,0.271 0.698,0.427 0.396,0.156 10 false BCB+ 0.094,1.719 0.656,1.875 0.563,0.156 10 false BGND 1.5,0.281 2,0.438 0.5,0.156 10 false R126
*a Component with harness connected
(Television Camera Controller)


Remove the television camera controller with the connector still connected.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R126-37 (BGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R126-15 (BCB+) - R126-37 (BGND) Ignition switch ON 5.5 to 7.05 V
R126-15 (BCB+) - R126-37 (BGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK FRONT TELEVISION CAMERA ASSEMBLY (BCV+, BGND)

NG

4.CHECK FRONT TELEVISION CAMERA ASSEMBLY (BCV+, BGND)
a.

Remove the television camera controller with the connector still connected.


b.

Using an oscilloscope, check the waveform of the front television camera assembly.

HINT:

A waterproof connector is used for the front television camera assembly. Therefore, inspect the waveform at the television camera controller with the connector connected.


E430500C57
0.75,0.292 1.25,0.542 0.5,0.25 1.75,1.917 1.583,1.917 1.583,1.917 0.656,1.104 true 4.302,2.052 4.104,1.552 true 6.333,2.052 6.083,1.406 true 5.802,2.031 5.969,1.458 true 3.813,2.031 3.969,1.594 true 1,2.198 0.854,2.198 0.854,2.198 0.531,1.115 true 1.833,1.833 2.427,2.135 0.594,0.302 10 false BCV+ 1.104,2.135 1.583,2.313 0.479,0.177 10 false BGND 3.365,1.188 3.844,1.365 0.479,0.177 10 false GND 5.271,1.188 5.75,1.365 0.479,0.177 10 false GND 0.083,0.063 0.563,0.24 0.479,0.177 10 false *a 3.469,0.083 3.948,0.26 0.479,0.177 10 false *b 5.417,0.073 5.896,0.25 0.479,0.177 10 false *c 6.302,2.094 6.781,2.271 0.479,0.177 10 false *e 4.271,2.083 4.75,2.26 0.479,0.177 10 false *e 5.688,2.094 6.167,2.271 0.479,0.177 10 false *d 3.74,2.083 4.219,2.26 0.479,0.177 10 false *d 0.823,0.323 1.302,0.5 0.479,0.177 10 false R126
*a Component with harness connected
(Television Camera Controller)
*b Waveform 1 (camera lens not covered, displaying an image)
*c Waveform 2 (camera lens covered, blacking out the screen) *d Synchronization Signal
*e Video Waveform - -


HINT:
·

The video waveform changes according to the image sent by the front television camera assembly.

·

The video waveform is constantly output when the ignition switch is turned to ACC.



Measurement Condition
Item Content
Terminal No. (Symbol) R126-36 (BCV+) - R126-37 (BGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON, panoramic view monitor system operating

OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

NG