Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2021.02
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0351447 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1686  Driver Side Camera Video Sync Signal Malfunction  


DESCRIPTION

This DTC is stored if the television camera controller judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the driver side television camera assembly to the television camera controller.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1686 Driver Side Camera Video Sync Signal Malfunction Side camera feedback malfunction
·

Harness or connector

·

Television camera controller

·

Side television camera assembly LH

·

Outer rear view mirror assembly LH



WIRING DIAGRAM

E457467E09
5.365,2.594 5.823,2.792 0.458,0.198 10 false R126 5.375,2.771 7.156,3.5 1.781,0.729 10 false Television Camera Controller 0.938,3.135 3.292,3.427 2.354,0.292 10 false Outer Rear View Mirror Assembly LH 0.906,2.313 2.344,2.719 1.438,0.406 10 false Side Television Camera Assembly LH 0.938,2.948 1.396,3.146 0.458,0.198 10 false O22 6,2.198 6.698,2.438 0.698,0.24 10 false SGND 6,1.76 6.698,2 0.698,0.24 10 false LGND 6,1.344 6.698,1.583 0.698,0.24 10 false LCV- 6,0.927 6.698,1.167 0.698,0.24 10 false LCV+ 6,0.552 6.698,0.792 0.698,0.24 10 false LCB+ 3.385,0.417 4.083,0.656 0.698,0.24 10 false LCB+ 3.396,0.802 4.094,1.042 0.698,0.24 10 false LCV+ 3.417,1.188 4.115,1.427 0.698,0.24 10 false LCV- 3.354,1.635 4.052,1.875 0.698,0.24 10 false LGND 5.698,0.406 6.01,0.604 0.313,0.198 10 false 12 5.708,0.802 6.021,1 0.313,0.198 10 false 10 5.708,1.208 6.021,1.406 0.313,0.198 10 false 34 5.719,1.646 6.031,1.844 0.313,0.198 10 false 35 5.729,2.063 6.042,2.26 0.313,0.198 10 false 11 3.875,1.646 4.188,1.844 0.313,0.198 10 false 13 3.865,1.198 4.177,1.396 0.313,0.198 10 false 12 3.896,0.802 4.208,1 0.313,0.198 10 false 1 3.885,0.438 4.198,0.635 0.313,0.198 10 false 2 4.75,2.104 4.979,2.292 0.229,0.188 10 false * 1.656,3.49 2.688,3.802 1.031,0.313 10 false *: Shielded 1.74,0.406 2.438,0.646 0.698,0.24 10 false LCB+ 1.74,0.844 2.438,1.083 0.698,0.24 10 false LCV+ 1.76,1.24 2.458,1.479 0.698,0.24 10 false LCV- 1.719,1.656 2.417,1.896 0.698,0.24 10 false LGND 2.24,0.406 2.552,0.604 0.313,0.198 10 false 1 2.25,0.771 2.563,0.969 0.313,0.198 10 false 5 2.25,1.156 2.563,1.354 0.313,0.198 10 false 7 2.25,1.625 2.563,1.823 0.313,0.198 10 false 3 0.375,2.302 0.688,2.5 0.313,0.198 10 false A 3.365,2.031 4.063,2.271 0.698,0.24 10 false SGND 3.906,2.042 4.219,2.24 0.313,0.198 10 false 14

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1686 is not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - OUTER REAR VIEW MIRROR ASSEMBLY LH)
2.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - OUTER REAR VIEW MIRROR ASSEMBLY LH)
a.

Disconnect the R126 television camera controller connector.


b.

Disconnect the O22 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R126-12 (LCB+) - O22-2 (LCB+) Always Below 1 Ω
R126-10 (LCV+) - O22-1 (LCV+) Always Below 1 Ω
R126-34 (LCV-) - O22-12 (LCV-) Always Below 1 Ω
R126-35 (LGND) - O22-13 (LGND) Always Below 1 Ω
R126-12 (LCB+) or O22-2 (LCB+) - Body ground Always 10 kΩ or higher
R126-10 (LCV+) or O22-1 (LCV+) - Body ground Always 10 kΩ or higher
R126-34 (LCV-) or O22-12 (LCV-) - Body ground Always 10 kΩ or higher
R126-35 (LGND) or O22-13 (LGND) - Body ground Always 10 kΩ or higher
R126-11 (SGND) or O22-14 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK TELEVISION CAMERA CONTROLLER (LCV-, LGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TELEVISION CAMERA CONTROLLER (LCV-, LGND)
a.
E330226C62
1.698,1.802 1.469,1.802 1.469,1.802 1.375,1.156 true 0.979,1.792 1.146,1.792 1.146,1.792 1.292,1.146 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 0.583,1.719 1.083,1.875 0.5,0.156 10 false LGND 1.76,1.719 2.26,1.875 0.5,0.156 10 false LCV-
*a Component without harness connected
(Television Camera Controller)


Disconnect the R126 television camera controller connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
35 (LGND) - Body ground Always Below 1 Ω
34 (LCV-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK TELEVISION CAMERA CONTROLLER (LCB+, LGND)

NG

4.CHECK TELEVISION CAMERA CONTROLLER (LCB+, LGND)
a.
E407111C70
1.417,0.25 1.917,0.5 0.5,0.25 0.667,1.917 1,1.917 1,1.917 1.302,1.135 true 0.917,0.667 1.167,0.667 1.167,0.667 1.25,0.958 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 0.542,0.583 1.031,0.75 0.49,0.167 10 false LCB+ 0.25,1.833 0.813,1.99 0.563,0.156 10 false LGND 1.5,0.281 2,0.438 0.5,0.156 10 false R126
*a Component with harness connected
(Television Camera Controller)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R126-35 (LGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R126-12 (LCB+) - R126-35 (LGND) Ignition switch ON 5.5 to 7.05 V
R126-12 (LCB+) - R126-35 (LGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

5.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH (LCV+, LGND)

NG

5.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH (LCV+, LGND)
a.

Using an oscilloscope, check the waveform of the side television camera assembly LH.

HINT:

A waterproof connector is used for the side television camera assembly LH. Therefore, inspect the waveform at the television camera controller with the connector connected.


E430500C59
0.75,0.292 1.25,0.542 0.5,0.25 0.708,1.104 0.646,2.094 0.646,2.094 0.49,2.094 true 1.104,1.333 0.958,1.333 0.958,1.333 0.802,1.021 true 4.302,2.052 4.104,1.552 true 6.333,2.052 6.083,1.406 true 5.802,2.031 5.969,1.458 true 3.813,2.031 3.969,1.594 true 1.188,1.26 1.917,1.51 0.729,0.25 10 false LCV+ 0.073,2.021 0.552,2.198 0.479,0.177 10 false LGND 3.365,1.156 3.844,1.333 0.479,0.177 10 false GND 5.26,1.167 5.74,1.344 0.479,0.177 10 false GND 0.083,0.063 0.563,0.24 0.479,0.177 10 false *a 3.469,0.083 3.948,0.26 0.479,0.177 10 false *b 5.417,0.073 5.896,0.25 0.479,0.177 10 false *c 6.302,2.094 6.781,2.271 0.479,0.177 10 false *e 4.271,2.083 4.75,2.26 0.479,0.177 10 false *e 5.688,2.094 6.167,2.271 0.479,0.177 10 false *d 3.74,2.083 4.219,2.26 0.479,0.177 10 false *d 0.833,0.323 1.313,0.5 0.479,0.177 10 false R126
*a Component with harness connected
(Television Camera Controller)
*b Waveform 1 (camera lens not covered, displaying an image)
*c Waveform 2 (camera lens covered, blacking out the screen) *d Synchronization Signal
*e Video Waveform - -


HINT:
·

The video waveform changes according to the image sent by the side television camera assembly LH.

·

The video waveform is constantly output when the ignition switch is ACC.



Measurement Condition
Item Content
Tester Connection R126-10 (LCV+) - R126-35 (LGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON, panoramic view monitor switch on

OK:

Waveform is similar to that shown in illustration.



Result:
Proceed to
OK
NG



OK

NG

6.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
6.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
a.
E461664C17
0.646,0.833 1.146,1.083 0.5,0.25 0.198,2.281 0.698,2.531 0.5,0.25 0.99,0.375 1.24,0.375 1.24,0.375 1.427,0.76 true 2.406,0.365 2.156,0.365 2.156,0.365 1.979,0.75 true 1,1.427 1.25,1.427 1.25,1.427 1.427,1.104 true 0.708,1.844 0.958,1.844 0.958,1.844 1.021,2.396 true 1.875,1.75 1.625,1.75 1.625,1.75 1.156,2.365 true 1.833,3.188 1.583,3.188 1.583,3.188 1.208,2.656 true 0.625,3.167 0.875,3.167 0.875,3.167 1.031,2.688 true 2.531,1.365 2.281,1.365 2.281,1.365 1.99,1.031 true 1.917,1.677 2.531,1.875 0.615,0.198 10 false LCB+ 2.458,0.281 3.073,0.479 0.615,0.198 10 false LCB+ 0.604,1.333 1.219,1.531 0.615,0.198 10 false LCV- 0.542,0.281 1.156,0.479 0.615,0.198 10 false LGND 0.344,1.76 0.833,2.083 0.49,0.323 10 false LCV+ 1.865,3.104 2.365,3.344 0.5,0.24 10 false LGND 0.25,3.073 0.719,3.292 0.469,0.219 10 false LCV- 0.833,0.875 1.448,1.073 0.615,0.198 10 false A 0.292,2.313 0.906,2.51 0.615,0.198 10 false O22 0.052,0.052 0.667,0.25 0.615,0.198 10 false *a 0.063,1.625 0.677,1.823 0.615,0.198 10 false *b 2.583,1.271 3.198,1.469 0.615,0.198 10 false LCV+
*a Front view of wire harness connector
(to Side Television Camera Assembly LH)
*b Front view of wire harness connector
(to Vehicle Wire Harness Connector)


Disconnect the outer rear view mirror assembly LH connector.


b.

Disconnect the side television camera assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (LCB+) - O22-2 (LCB+) Always Below 1 Ω
A-5 (LCV+) - O22-1 (LCV+) Always Below 1 Ω
A-7 (LCV-) - O22-12 (LCV-) Always Below 1 Ω
A-3 (LGND) - O22-13 (LGND) Always Below 1 Ω
A-1 (LCB+) or O22-2 (LCB+) - Body ground Always 10 kΩ or higher
A-5 (LCV+) or O22-1 (LCV+) - Body ground Always 10 kΩ or higher
A-7 (LCV-) or O22-12 (LCV-) - Body ground Always 10 kΩ or higher
A-3 (LGND) or O22-13 (LGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

7.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH
a.

Replace the side television camera assembly LH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK FOR DTC
8.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1686 is not output.



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY LH IS DEFECTIVE)

NG