Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2021.02
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0351447 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1687  Over Current Detected in Driver Side Camera  


DESCRIPTION

This DTC is stored if the television camera controller judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the driver side television camera assembly to the television camera controller.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1687 Over Current Detected in Driver Side Camera Side camera current malfunction
·

Harness or connector

·

Television camera controller

·

Side television camera assembly LH

·

Outer rear view mirror assembly LH



WIRING DIAGRAM

E407571E60
0.938,2.167 3.542,2.438 2.604,0.271 10 false Outer Rear View Mirror Assembly LH 1.094,1.333 2.531,1.865 1.438,0.531 10 false Side Television Camera Assembly LH 3.594,0.344 4.115,0.646 0.521,0.302 10 false LCB+ 4.094,0.344 4.302,0.594 0.208,0.25 10 false 2 3.573,0.823 4.063,1.052 0.49,0.229 10 false LGND 4.083,0.823 4.313,1.115 0.229,0.292 10 false 13 5.375,1.604 7.156,2.135 1.781,0.531 10 false Television Camera Controller 5.375,1.427 5.969,1.604 0.594,0.177 10 false R126 5.948,0.469 6.354,0.625 0.406,0.156 10 false LCB+ 5.958,0.958 6.521,1.229 0.563,0.271 10 false LGND 5.667,0.344 5.875,0.563 0.208,0.219 10 false 12 5.667,0.833 5.896,1.042 0.229,0.208 10 false 35 0.938,2 1.531,2.177 0.594,0.177 10 false O22 0.385,1.302 0.615,1.594 0.229,0.292 10 false A 1.75,0.396 2.271,0.698 0.521,0.302 10 false LCB+ 1.719,0.917 2.24,1.219 0.521,0.302 10 false LGND 2.219,0.365 2.427,0.615 0.208,0.25 10 false 1 2.24,0.833 2.448,1.083 0.208,0.25 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1687 is not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - OUTER REAR VIEW MIRROR ASSEMBLY LH)
2.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - OUTER REAR VIEW MIRROR ASSEMBLY LH)
a.

Disconnect the R126 television camera controller connector.


b.

Disconnect the O22 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R126-12 (LCB+) - O22-2 (LCB+) Always Below 1 Ω
R126-35 (LGND) - O22-13 (LGND) Always Below 1 Ω
R126-12 (LCB+) or O22-2 (LCB+) - Body ground Always 10 kΩ or higher
R126-35 (LGND) or O22-13 (LGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK TELEVISION CAMERA CONTROLLER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TELEVISION CAMERA CONTROLLER
a.
E407111C71
1.417,0.25 1.917,0.5 0.5,0.25 0.667,1.917 1,1.917 1,1.917 1.302,1.135 true 0.917,0.667 1.167,0.667 1.167,0.667 1.25,0.958 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 0.542,0.583 1.031,0.75 0.49,0.167 10 false LCB+ 0.25,1.833 0.813,1.99 0.563,0.156 10 false LGND 1.5,0.292 2,0.448 0.5,0.156 10 false R126
*a Component with harness connected
(Television Camera Controller)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R126-35 (LGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R126-12 (LCB+) - R126-35 (LGND) Ignition switch ON 5.5 to 7.05 V
R126-12 (LCB+) - R126-35 (LGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
a.
E461664C18
0.646,0.833 1.146,1.083 0.5,0.25 0.198,2.281 0.698,2.531 0.5,0.25 0.99,0.375 1.24,0.375 1.24,0.375 1.427,0.76 true 2.406,0.365 2.156,0.365 2.156,0.365 1.979,0.75 true 1,1.427 1.25,1.427 1.25,1.427 1.427,1.104 true 0.708,1.844 0.958,1.844 0.958,1.844 1.021,2.396 true 1.875,1.75 1.625,1.75 1.625,1.75 1.156,2.365 true 1.833,3.188 1.583,3.188 1.583,3.188 1.208,2.656 true 0.625,3.167 0.875,3.167 0.875,3.167 1.031,2.688 true 2.531,1.365 2.281,1.365 2.281,1.365 1.99,1.031 true 1.917,1.677 2.531,1.875 0.615,0.198 10 false LCB+ 2.458,0.281 3.073,0.479 0.615,0.198 10 false LCB+ 0.604,1.333 1.219,1.531 0.615,0.198 10 false LCV- 0.542,0.281 1.156,0.479 0.615,0.198 10 false LGND 0.344,1.76 0.833,2.083 0.49,0.323 10 false LCV+ 1.865,3.104 2.365,3.344 0.5,0.24 10 false LGND 0.25,3.073 0.719,3.292 0.469,0.219 10 false LCV- 0.833,0.875 1.448,1.073 0.615,0.198 10 false A 0.292,2.313 0.906,2.51 0.615,0.198 10 false O22 0.052,0.052 0.667,0.25 0.615,0.198 10 false *a 0.063,1.625 0.677,1.823 0.615,0.198 10 false *b 2.583,1.271 3.198,1.469 0.615,0.198 10 false LCV+
*a Front view of wire harness connector
(to Side Television Camera Assembly LH)
*b Front view of wire harness connector
(to Vehicle Wire Harness Connector)


Disconnect the side television camera assembly LH connector.


b.

Disconnect the outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (LCB+) - O22-2 (LCB+) Always Below 1 Ω
A-3 (LGND) - O22-13 (LGND) Always Below 1 Ω
A-1 (LCB+) or O22-2 (LCB+) - Body ground Always 10 kΩ or higher
A-3 (LGND) or O22-13 (LGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

5.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH
a.

Replace the side television camera assembly LH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1687 is not output.



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY LH IS DEFECTIVE)

NG