Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2021.02
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0328876 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  U0232  Lost Communication with Blind Spot Monitor Slave Module  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH judges that there is a communication problem with the blind spot monitor sensor LH.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0232 Lost Communication with Blind Spot Monitor Slave Module The blind spot monitor sensor (master) cannot receive signals from the blind spot monitor sensor (slave)
·

Open or short in CAN bus main wire or connector

·

Open or short in No. 5 junction connector*

·

Blind spot monitor sensor LH

·

Power source circuit of blind spot monitor sensor LH

·

Blind spot monitor sensor LH ground circuit

·

Blind spot monitor sensor RH



*: w/ Parking Support Brake System


WIRING DIAGRAM

w/ Parking Support Brake System
E334324E68
5.573,2.635 6.74,3.083 1.167,0.448 10 false Blind Spot Monitor Sensor RH 2.25,2.635 3.417,3.073 1.167,0.438 10 false Blind Spot Monitor Sensor LH 3.938,2.625 4.958,3.073 1.021,0.448 10 false No. 5 Junction Connector 0.083,1.26 0.927,1.677 0.844,0.417 10 false from IG1-NO. 1 Relay 1.25,1.427 2.271,1.719 1.021,0.292 10 false ECU-IG1 NO. 4 2.323,1.281 3.198,1.833 0.875,0.552 10 false BLB 2.927,0.99 3.802,1.542 0.875,0.552 10 false CA2P 5.688,0.99 6.563,1.542 0.875,0.552 10 false CA2P 5.688,1.854 6.563,2.406 0.875,0.552 10 false CA2N 2.927,1.854 3.802,2.406 0.875,0.552 10 false CA2N 2.323,1.917 3.198,2.469 0.875,0.552 10 false BLGD 3.948,2.458 4.75,2.667 0.802,0.208 10 false R100 5.583,2.469 6.031,2.688 0.448,0.219 10 false W5 2.26,2.469 2.708,2.688 0.448,0.219 10 false W6 3.854,1.844 4.729,2.396 0.875,0.552 10 false 14 4.885,1.833 5.281,2.083 0.396,0.25 10 false 13 3.896,1 4.771,1.552 0.875,0.552 10 false 3 4.906,1 5.781,1.552 0.875,0.552 10 false 2 2.156,1.156 3.031,1.708 0.875,0.552 10 false 5 2.104,1.792 2.979,2.344 0.875,0.552 10 false 10 3.385,1.833 4.26,2.385 0.875,0.552 10 false 6 5.5,1.01 6.375,1.563 0.875,0.552 10 false 1 3.375,0.99 4.25,1.542 0.875,0.552 10 false 1 5.479,1.833 6.354,2.385 0.875,0.552 10 false 6

w/o Parking Support Brake System
E334367E74
3.156,2.667 4.323,3.188 1.167,0.521 10 false Blind Spot Monitor Sensor LH 5.635,2.646 6.802,3.167 1.167,0.521 10 false Blind Spot Monitor Sensor RH 0.323,1.292 1.344,1.906 1.021,0.615 10 false from IG1-NO. 1 Relay 1.875,1.438 2.979,1.656 1.104,0.219 10 false ECU-IG1 NO. 4 3.188,1.302 4.208,1.917 1.021,0.615 10 false BLB 3.198,1.938 3.75,2.198 0.552,0.26 10 false BLGD 3.156,2.479 3.448,2.688 0.292,0.208 10 false W6 5.625,2.469 5.917,2.677 0.292,0.208 10 false W5 5.719,1.875 6.135,2.115 0.417,0.24 10 false CA2N 3.802,1.844 4.219,2.083 0.417,0.24 10 false CA2N 3.802,1 4.219,1.24 0.417,0.24 10 false CA2P 5.708,0.969 6.125,1.208 0.417,0.24 10 false CA2P 4.25,1.01 4.667,1.25 0.417,0.24 10 false 1 5.5,1 5.917,1.24 0.417,0.24 10 false 1 5.542,1.833 5.958,2.073 0.417,0.24 10 false 6 4.229,1.823 4.646,2.063 0.417,0.24 10 false 6 3.031,1.156 3.448,1.396 0.417,0.24 10 false 5 2.938,1.813 3.354,2.052 0.417,0.24 10 false 10

CAUTION / NOTICE / HINT

NOTICE:
·

When checking for DTCs, make sure that the blind spot monitor system is turned on.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:
·

Operating the engine switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Parking Support Brake System A
w/o Parking Support Brake System B



A

2.CHECK DTC OUTPUT (PARKING SUPPORT BRAKE SYSTEM)

B

16.CHECK CAN BUS MAIN WIRE
2.CHECK DTC OUTPUT (PARKING SUPPORT BRAKE SYSTEM)
a.

Using the GTS, check for DTCs according to the prompts on the screen.

Body Electrical > Clearance Warning > Trouble Codes
50001 438
Standard:

The clearance warning ECU assembly does not output DTCs U117787 and U117887 simultaneously.



Result:
Proceed to
OK
NG



OK

3.CHECK CAN BUS MAIN WIRE

NG

GO TO PARKING SUPPORT BRAKE SYSTEM (DTC U117787)

3.CHECK CAN BUS MAIN WIRE
a.

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal.


c.
E366089C15
0.125,1.208 0.531,1.479 0.406,0.271 1.5,2.833 1.906,3.104 0.406,0.271 2.333,4 2.417,4.406 2.417,4.406 2.583,4.406 false 1.167,3.042 1.333,3.042 1.333,3.042 1.625,3.438 false 2.01,1.76 2.208,2.229 2.208,2.229 2.375,2.229 false 2.01,1.448 2.281,0.656 2.281,0.656 2.448,0.656 false 0.25,2.844 0.563,3 0.313,0.156 10 false *1 0.25,0.167 0.563,0.323 0.313,0.156 10 false *a 0.229,1.271 0.542,1.469 0.313,0.198 10 false W5 1.552,2.885 2.063,3.094 0.51,0.208 10 false K154 2.51,0.583 3.125,0.781 0.615,0.198 10 false CA2P 2.438,2.156 3.052,2.354 0.615,0.198 10 false CA2N 2.646,4.323 3.104,4.521 0.458,0.198 10 false BAT 0.917,2.969 1.292,3.156 0.375,0.188 10 false CG
*1 DLC3
*a Component with harness connected
(Blind Spot Monitor Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
W5-1 (CA2P) - W5-6 (CA2N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or more: Open circuit in main bus lines
W5-1 (CA2P) - K154-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CA2P short to ground
W5-6 (CA2N) - K154-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CA2N short to ground
W5-1 (CA2P) - K154-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CA2P +B short
W5-6 (CA2N) - K154-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CA2N +B short



d.

Reconnect the cable to the negative (-) battery terminal.


Result:
Result Proceed to
OK A
Open circuit in CAN main bus lines B
Short circuit between bus lines C
·

Short to ground

·

+B short


D



A

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BODY GROUND)

B

7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 JUNCTION CONNECTOR)

C

10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR)

D

13.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR)
4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BODY GROUND)

OK

5.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - POWER SOURCE)

OK

6.CHECK DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK DTC
a.

Turn the engine switch off.


b.

Turn the engine switch on (IG).


c.

Check for DTCs.

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313

OK:

No DTCs are output.


Result:
Proceed to
OK
NG



OK

NG

7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 JUNCTION CONNECTOR)
a.
E331799C13
1.521,0.25 1.938,0.5 0.417,0.25 0.906,2.156 1.021,3.115 1.021,3.115 1.198,3.115 false 1.115,1.875 1.26,0.938 1.26,0.938 1.438,0.938 false 1.135,2.167 1.333,2.802 1.333,2.802 1.51,2.802 false 0.906,1.833 1.083,0.677 1.083,0.677 1.198,0.677 false 0.083,0.115 0.396,0.271 0.313,0.156 10 false *a 1.563,0.292 2.021,0.49 0.458,0.198 10 false R100 1.271,0.573 1.885,0.771 0.615,0.198 10 false CANH*b 1.49,0.833 2.104,1.031 0.615,0.198 10 false CANH*c 1.271,3.031 1.885,3.229 0.615,0.198 10 false CANL*b 1.604,2.698 2.219,2.896 0.615,0.198 10 false CANL*c
*a Front view of wire harness connector
(to No. 5 Junction Connector)
*b to blind spot monitor sensor RH CAN main wire
*c to blind spot monitor sensor LH CAN main wire


Disconnect the R100 No. 5 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R100-3 (CANH) - R100-14(CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
R100-2 (CANH) - R100-13(CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor RH CAN main wire) B
NG (to blind spot monitor sensor LH CAN main wire) C



A

REPLACE NO. 5 JUNCTION CONNECTOR

B

8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH)

C

9.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH)
8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH)
a.

Reconnect the R100 No. 5 junction connector.


b.
C368219C02
1.448,0.219 1.865,0.469 0.417,0.25 0.698,1.656 0.906,1.656 0.906,1.656 1.406,1.042 false 2.01,1.813 1.76,1.813 1.76,1.813 1.448,1.198 false 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 1.531,0.26 1.844,0.458 0.313,0.198 10 false W5 0.292,1.563 0.771,1.792 0.479,0.229 10 false CA2P 2.063,1.729 2.542,1.958 0.479,0.229 10 false CA2N
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)


Disconnect the W5 blind spot monitor sensor RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W5-1 (CA2P) - W5-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH - NO. 5 JUNCTION CONNECTOR)

9.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH)
a.

Reconnect the R100 No. 5 junction connector.


b.
C368219C03
1.448,0.219 1.865,0.469 0.417,0.25 0.698,1.656 0.906,1.656 0.906,1.656 1.406,1.042 false 2.01,1.813 1.76,1.813 1.76,1.813 1.448,1.198 false 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 1.531,0.26 1.844,0.458 0.313,0.198 10 false W6 0.292,1.563 0.771,1.792 0.479,0.229 10 false CA2P 2.063,1.729 2.542,1.958 0.479,0.229 10 false CA2N
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Disconnect the W6 blind spot monitor sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W6-1 (CA2P) - W6-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH - No. 5 JUNCTION CONNECTOR)

10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR)
a.
E331799C13
1.521,0.25 1.938,0.5 0.417,0.25 0.906,2.156 1.021,3.115 1.021,3.115 1.198,3.115 false 1.115,1.875 1.26,0.938 1.26,0.938 1.438,0.938 false 1.135,2.167 1.333,2.802 1.333,2.802 1.51,2.802 false 0.906,1.833 1.083,0.677 1.083,0.677 1.198,0.677 false 0.083,0.115 0.396,0.271 0.313,0.156 10 false *a 1.563,0.292 2.021,0.49 0.458,0.198 10 false R100 1.271,0.573 1.885,0.771 0.615,0.198 10 false CANH*b 1.49,0.833 2.104,1.031 0.615,0.198 10 false CANH*c 1.271,3.031 1.885,3.229 0.615,0.198 10 false CANL*b 1.604,2.698 2.219,2.896 0.615,0.198 10 false CANL*c
*a Front view of wire harness connector
(to No. 5 Junction Connector)
*b to blind spot monitor sensor RH CAN main wire
*c to blind spot monitor sensor LH CAN main wire


Disconnect the R100 No. 5 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R100-3 (CANH) - R100-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
R100-2 (CANH) - R100-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor RH CAN main wire) B
NG (to blind spot monitor sensor LH CAN main wire) C



A

REPLACE NO. 5 JUNCTION CONNECTOR

B

11.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH)

C

12.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH)
11.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH)
a.

Reconnect the R100 No. 5 junction connector.


b.
C368219C02
1.448,0.219 1.865,0.469 0.417,0.25 0.698,1.656 0.906,1.656 0.906,1.656 1.406,1.042 false 2.01,1.813 1.76,1.813 1.76,1.813 1.448,1.198 false 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 1.531,0.26 1.844,0.458 0.313,0.198 10 false W5 0.292,1.563 0.771,1.792 0.479,0.229 10 false CA2P 2.063,1.729 2.542,1.958 0.479,0.229 10 false CA2N
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)


Disconnect the W5 blind spot monitor sensor RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W5-1 (CA2P) - W5-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH - NO. 5 JUNCTION CONNECTOR)

12.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH)
a.

Reconnect the R100 No. 5 junction connector.


b.
C368219C03
1.448,0.219 1.865,0.469 0.417,0.25 0.698,1.656 0.906,1.656 0.906,1.656 1.406,1.042 false 2.01,1.813 1.76,1.813 1.76,1.813 1.448,1.198 false 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 1.531,0.26 1.844,0.458 0.313,0.198 10 false W6 0.292,1.563 0.771,1.792 0.479,0.229 10 false CA2P 2.063,1.729 2.542,1.958 0.479,0.229 10 false CA2N
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Disconnect the W6 blind spot monitor sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W6-1 (CA2P) - W6-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH - NO. 5 JUNCTION CONNECTOR)

13.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR)
a.

Disconnect the R100 No. 5 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C381329C17
1.979,0.5 2.396,0.75 0.417,0.25 5.635,0.5 6.052,0.75 0.417,0.25 6.5,2.146 6.5,1.76 true 5.75,1.281 5.333,0.833 5.333,0.833 5.083,0.833 true 0.833,2 1.083,2 1.083,2 1.604,1.698 true 0.833,1.333 1.083,1.333 1.083,1.333 1.542,1.521 true 0.833,2.417 1.083,2.417 1.083,2.417 1.75,1.708 true 1.719,1.531 1.083,0.833 1.083,0.833 0.833,0.833 true 4.083,0.177 4.396,0.333 0.313,0.156 10 false *1 0.156,0.115 0.469,0.271 0.313,0.156 10 false *a 0.26,0.75 0.927,0.99 0.667,0.24 10 false CANH*c 2.021,0.542 2.521,0.75 0.5,0.208 10 false R100 5.688,0.542 6.063,0.74 0.375,0.198 10 false K154 4.813,0.75 5.188,0.948 0.375,0.198 10 false CG 6.385,2.219 6.76,2.417 0.375,0.198 10 false BAT 0.292,1.885 0.958,2.125 0.667,0.24 10 false CANL*b 0.271,1.25 0.938,1.49 0.667,0.24 10 false CANH*b 0.292,2.323 0.958,2.563 0.667,0.24 10 false CANL*c
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 5 Junction Connector)
*b to blind spot monitor sensor RH CAN main wire
*c to blind spot monitor sensor LH CAN main wire - -


Standard Resistance:
Tester Connection Condition Specified Condition
R100-3 (CANH) - K154-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
R100-14 (CANL) - K154-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
R100-3 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
R100-14 (CANL) - K154-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
R100-2 (CANH) - K154-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
R100-13 (CANL) - K154-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
R100-2 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
R100-13 (CANL) - K154-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor RH CAN main wire) B
NG (to blind spot monitor sensor LH CAN main wire) C



A

REPLACE NO. 5 JUNCTION CONNECTOR

B

14.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH)

C

15.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH)
14.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH)
a.

Reconnect the R100 No. 5 junction connector.


b.

Disconnect the W5 blind spot monitor sensor RH connector.


c.
E458912C07
1.5,1.833 1.917,2.083 0.417,0.25 1.417,0.25 1.833,0.5 0.417,0.25 0.729,0.771 0.917,0.771 0.917,0.771 1.385,1.021 false 0.75,1.49 0.938,1.49 0.938,1.49 1.365,1.229 false 1.125,1.948 1.313,1.948 1.313,1.948 1.625,2.354 false 2.271,2.823 2.458,3.042 2.458,3.042 2.573,3.042 false 0.313,1.813 0.625,1.969 0.313,0.156 10 false *1 0.177,0.198 0.49,0.354 0.313,0.156 10 false *a 1.552,1.875 2.063,2.094 0.51,0.219 10 false K154 1.51,0.292 1.823,0.49 0.313,0.198 10 false W5 0.333,0.708 0.948,0.906 0.615,0.198 10 false CA2P 0.344,1.406 0.958,1.604 0.615,0.198 10 false CA2N 2.656,2.948 3.271,3.146 0.615,0.198 10 false BAT 0.865,1.875 1.479,2.073 0.615,0.198 10 false CG
*1 DLC3
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W5-1 (CA2P) - K154-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
W5-6 (CA2N) - K154-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
W5-1 (CA2P) - K154-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
W5-6 (CA2N) - K154-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH - NO. 5 JUNCTION CONNECTOR)

15.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH)
a.

Reconnect the R100 No. 5 junction connector.


b.

Disconnect the W6 blind spot monitor sensor LH connector.


c.
E458912C08
1.5,1.833 1.917,2.083 0.417,0.25 1.417,0.25 1.833,0.5 0.417,0.25 0.729,0.771 0.917,0.771 0.917,0.771 1.385,1.021 false 0.75,1.49 0.938,1.49 0.938,1.49 1.365,1.229 false 1.125,1.948 1.313,1.948 1.313,1.948 1.625,2.354 false 2.271,2.823 2.458,3.042 2.458,3.042 2.573,3.042 false 0.313,1.813 0.625,1.969 0.313,0.156 10 false *1 0.177,0.198 0.49,0.354 0.313,0.156 10 false *a 1.552,1.875 2.01,2.198 0.458,0.323 10 false K154 1.51,0.292 1.823,0.49 0.313,0.198 10 false W6 0.333,0.708 0.948,0.906 0.615,0.198 10 false CA2P 0.344,1.406 0.958,1.604 0.615,0.198 10 false CA2N 2.656,2.948 3.271,3.146 0.615,0.198 10 false BAT 0.865,1.875 1.479,2.073 0.615,0.198 10 false CG
*1 DLC3
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W6-1 (CA2P) - K154-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
W6-6 (CA2N) - K154-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
W6-1 (CA2P) - K154-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
W6-6 (CA2N) - K154-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH - NO. 5 JUNCTION CONNECTOR)

16.CHECK CAN BUS MAIN WIRE
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.
E366089C12
0.125,1.208 0.531,1.479 0.406,0.271 1.5,2.833 1.906,3.104 0.406,0.271 2.333,4 2.417,4.406 2.417,4.406 2.583,4.406 false 1.167,3.042 1.333,3.042 1.333,3.042 1.625,3.438 false 2.01,1.76 2.208,2.229 2.208,2.229 2.375,2.229 false 2.01,1.448 2.281,0.656 2.281,0.656 2.448,0.656 false 0.25,2.844 0.563,3 0.313,0.156 10 false *1 0.25,0.167 0.563,0.323 0.313,0.156 10 false *a 0.229,1.271 0.542,1.469 0.313,0.198 10 false O58 1.552,2.885 1.979,3.063 0.427,0.177 10 false K154 2.51,0.583 3.125,0.781 0.615,0.198 10 false CA2P 2.438,2.156 3.052,2.354 0.615,0.198 10 false CA2N 2.646,4.323 3.104,4.521 0.458,0.198 10 false BAT 0.917,2.969 1.292,3.156 0.375,0.188 10 false CG
*1 DLC3
*a Component with harness connected
(Blind spot monitor sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
W5-1 (CA2P) - W5-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or more: Open circuit in main bus lines
W5-1 (CA2P) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CA2P short to ground
W5-6 (CA2N) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CA2N short to ground
W5-1 (CA2P) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CA2P +B short
W5-6 (CA2N) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CA2N +B short



d.

Reconnect the cable to the negative (-) auxiliary battery terminal.


Result:
Result Proceed to
OK A
Open circuit in CAN main bus lines B
Short circuit between bus lines C
·

Short to ground

·

+B short


D



A

17.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BODY GROUND)

B

20.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH)

C

22.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH)

D

24.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH)
17.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BODY GROUND)

OK

18.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - POWER SOURCE)

OK

19.CHECK DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK DTC
a.

Turn the engine switch off.


b.

Turn the engine switch on (IG).


c.

Check for DTCs.

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313

OK:

No DTCs are output.


Result:
Proceed to
OK
NG



OK

NG

20.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
E359601C03
1.5,0.208 1.885,0.438 0.385,0.229 0.76,1.688 0.906,1.688 0.906,1.688 1.427,1.073 false 1.865,1.958 1.698,1.958 1.698,1.958 1.438,1.219 false 1.594,0.25 2.052,0.448 0.458,0.198 10 false W6 0.365,1.615 0.854,1.844 0.49,0.229 10 false CA2P 1.927,1.885 2.417,2.115 0.49,0.229 10 false CA2N 0.135,0.146 0.448,0.302 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to blind spot monitor sensor LH)


Disconnect the W6 blind spot monitor sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W6-1 (CA2P) -W6-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

21.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH)
21.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH)
a.

Reconnect the W6 blind spot monitor sensor LH connector.


b.
E359601C04
1.5,0.208 1.885,0.438 0.385,0.229 0.76,1.688 0.906,1.688 0.906,1.688 1.427,1.073 false 1.865,1.958 1.698,1.958 1.698,1.958 1.438,1.219 false 1.583,0.25 2.042,0.448 0.458,0.198 10 false W5 0.365,1.615 0.854,1.844 0.49,0.229 10 false CA2P 1.927,1.885 2.417,2.115 0.49,0.229 10 false CA2N 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to blind spot monitor sensor RH)


Disconnect the W5 blind spot monitor sensor RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W5-1 (CA2P) - W5-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BLIND SPOT MONITOR SENSOR LH)

22.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
E359601C03
1.5,0.208 1.885,0.438 0.385,0.229 0.76,1.688 0.906,1.688 0.906,1.688 1.427,1.073 false 1.865,1.958 1.698,1.958 1.698,1.958 1.438,1.219 false 1.594,0.25 2.052,0.448 0.458,0.198 10 false W6 0.365,1.615 0.854,1.844 0.49,0.229 10 false CA2P 1.927,1.885 2.417,2.115 0.49,0.229 10 false CA2N 0.135,0.146 0.448,0.302 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to blind spot monitor sensor LH)


Disconnect the W6 blind spot monitor sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W6-1 (CA2P) -W6-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

23.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH)
23.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH)
a.

Reconnect the W6 blind spot monitor sensor LH connector.


b.
E359601C04
1.5,0.208 1.885,0.438 0.385,0.229 0.76,1.688 0.906,1.688 0.906,1.688 1.427,1.073 false 1.865,1.958 1.698,1.958 1.698,1.958 1.438,1.219 false 1.583,0.25 2.042,0.448 0.458,0.198 10 false W5 0.365,1.615 0.854,1.844 0.49,0.229 10 false CA2P 1.927,1.885 2.417,2.115 0.49,0.229 10 false CA2N 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to blind spot monitor sensor RH)


Disconnect the W5 blind spot monitor sensor RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W5-1 (CA2P) - W5-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BLIND SPOT MONITOR SENSOR LH)

24.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the W6 blind spot monitor sensor LH connector.


c.
E461681C01
1.479,1.802 1.875,2.094 0.396,0.292 1.438,0.198 1.833,0.49 0.396,0.292 0.729,0.771 0.917,0.771 0.917,0.771 1.385,1.021 false 0.75,1.49 0.938,1.49 0.938,1.49 1.365,1.229 false 1.125,1.948 1.313,1.948 1.313,1.948 1.625,2.354 false 2.271,2.823 2.458,3.042 2.458,3.042 2.573,3.042 false 0.229,1.813 0.542,1.969 0.313,0.156 10 false *1 0.177,0.198 0.49,0.354 0.313,0.156 10 false *a 1.521,1.875 1.979,2.073 0.458,0.198 10 false K154 1.542,0.26 1.854,0.458 0.313,0.198 10 false W6 0.333,0.708 0.948,0.906 0.615,0.198 10 false CA2P 0.344,1.406 0.958,1.604 0.615,0.198 10 false CA2N 2.656,2.948 3.271,3.146 0.615,0.198 10 false BAT 0.865,1.875 1.479,2.073 0.615,0.198 10 false CG
*1 DLC3
*a Front view of wire harness connector
(to blind spot monitor sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W6-1 (CA2P) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
W6-6 (CA2N) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
W6-1 (CA2P) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
W6-6 (CA2N) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

25.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH)
25.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH)
a.

Disconnect the W5 blind spot monitor sensor RH connector.


b.
E334330C26
1.479,1.802 1.875,2.094 0.396,0.292 1.438,0.198 1.833,0.49 0.396,0.292 0.729,0.771 0.917,0.771 0.917,0.771 1.385,1.021 false 0.75,1.49 0.938,1.49 0.938,1.49 1.365,1.229 false 1.125,1.948 1.313,1.948 1.313,1.948 1.625,2.354 false 2.271,2.823 2.458,3.042 2.458,3.042 2.573,3.042 false 0.229,1.813 0.542,1.969 0.313,0.156 10 false *1 0.177,0.198 0.49,0.354 0.313,0.156 10 false *a 1.563,1.875 1.875,2.073 0.313,0.198 10 false K68 1.542,0.26 1.854,0.458 0.313,0.198 10 false W5 0.333,0.708 0.948,0.906 0.615,0.198 10 false CA2P 0.344,1.406 0.958,1.604 0.615,0.198 10 false CA2N 2.656,2.948 3.271,3.146 0.615,0.198 10 false BAT 0.865,1.875 1.479,2.073 0.615,0.198 10 false CG
*1 DLC3
*a Front view of wire harness connector
(to blind spot monitor sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W5-1 (CA2P) - K68-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
W5-6 (CA2N) - K68-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
W5-1 (CA2P) - K68-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
W5-6 (CA2N) - K68-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BLIND SPOT MONITOR SENSOR LH)