Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for ERA-GLONASS) › from 2021.02
RM33A0E _56 Audio / Visual / Telematics _072211 TELEMATICS _0351443 TELEMATICS SYSTEM(for ERA-GLONASS) C

TELEMATICS  TELEMATICS SYSTEM(for ERA-GLONASS)  B15C111  GNSS Antenna Circuit Short to Ground  B15C113  GNSS Antenna Circuit Open  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the roof antenna assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C111 GNSS Antenna Circuit Short to Ground Current to the roof antenna assembly is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Short circuit)
·

Telematics transceiver

·

Roof antenna assembly

·

Antenna divider*

·

Antenna cord sub-assembly (for Type A)

·

Antenna cord sub-assembly (for Type B)

·

No. 2 antenna cord sub-assembly

·

No. 5 antenna cord sub-assembly


B15C113 GNSS Antenna Circuit Open Current to the roof antenna assembly is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Open circuit)
·

Telematics transceiver

·

Roof antenna assembly

·

Antenna divider*

·

Antenna cord sub-assembly (for Type A)

·

Antenna cord sub-assembly (for Type B)

·

No. 2 antenna cord sub-assembly

·

No. 5 antenna cord sub-assembly



*: w/ Antenna Divider


WIRING DIAGRAM

w/o Antenna Divider
E342823E42
0.26,1.25 1.135,1.875 0.875,0.625 10 false Roof Antenna Assembly 0.271,1.073 0.427,1.271 0.156,0.198 10 false K 5.927,1.063 6.448,1.26 0.521,0.198 10 false B 6.146,1.24 6.875,1.813 0.729,0.573 10 false Telematics Transceiver 1.875,0.354 2.104,0.604 0.229,0.25 10 false 2 2.281,0.354 2.51,0.604 0.229,0.25 10 false 2 1.156,0.448 1.385,0.698 0.229,0.25 10 false 2 1.375,0.708 1.688,0.906 0.313,0.198 10 false *4 2.75,0.74 3.063,0.938 0.313,0.198 10 false *3 4.219,0.75 4.531,0.948 0.313,0.198 10 false *2 5.646,0.719 5.958,0.917 0.313,0.198 10 false *1 3.313,0.354 3.542,0.604 0.229,0.25 10 false 2 3.719,0.354 3.948,0.604 0.229,0.25 10 false 2 5.188,0.365 5.417,0.615 0.229,0.25 10 false 1 4.781,0.365 5.01,0.615 0.229,0.25 10 false 1 1.865,0.563 2.021,0.76 0.156,0.198 10 false J 2.292,0.563 2.448,0.76 0.156,0.198 10 false I 3.323,0.573 3.479,0.771 0.156,0.198 10 false H 3.719,0.563 3.875,0.76 0.156,0.198 10 false G 4.771,0.563 4.927,0.76 0.156,0.198 10 false E 5.177,0.563 5.74,0.76 0.563,0.198 10 false D 5.948,0.458 6.177,0.708 0.229,0.25 10 false 1 1.156,2.208 5.896,2.51 4.74,0.302 10 false *1: Antenna Cord Sub-assembly (for Type B) 1.156,2.542 5.844,2.865 4.688,0.323 10 false *2: Antenna Cord Sub-assembly (for Type A) 1.156,2.906 5.927,3.26 4.771,0.354 10 false *3: No. 2 Antenna Cord Sub-assembly 1.156,3.26 6.333,3.573 5.177,0.313 10 false *4: No. 5 Antenna Cord Sub-assembly

w/ Antenna Divider
E462867E02
0.125,1.25 1,1.875 0.875,0.625 10 false Roof Antenna Assembly 0.146,1.073 0.302,1.271 0.156,0.198 10 false K 6.271,1.052 6.792,1.25 0.521,0.198 10 false B 6.271,1.26 7,1.833 0.729,0.573 10 false Telematics Transceiver 1.667,0.354 1.896,0.604 0.229,0.25 10 false 2 2.063,0.354 2.292,0.604 0.229,0.25 10 false 2 0.948,0.448 1.177,0.698 0.229,0.25 10 false 2 1.156,0.708 1.469,0.906 0.313,0.198 10 false *4 2.469,0.74 2.781,0.938 0.313,0.198 10 false *3 3.698,0.75 4.01,0.948 0.313,0.198 10 false *2 5.948,0.74 6.26,0.938 0.313,0.198 10 false *1 2.917,0.354 3.146,0.604 0.229,0.25 10 false 2 3.323,0.354 3.552,0.604 0.229,0.25 10 false 2 5.573,0.365 5.802,0.615 0.229,0.25 10 false 1 5.177,0.365 5.406,0.615 0.229,0.25 10 false 1 1.667,0.563 1.823,0.76 0.156,0.198 10 false J 2.083,0.563 2.24,0.76 0.156,0.198 10 false I 2.906,0.573 3.063,0.771 0.156,0.198 10 false H 3.292,0.563 3.448,0.76 0.156,0.198 10 false G 5.177,0.573 5.333,0.771 0.156,0.198 10 false E 5.573,0.573 6.135,0.771 0.563,0.198 10 false D 6.083,0.438 6.313,0.688 0.229,0.25 10 false 1 1.156,2.208 5.896,2.51 4.74,0.302 10 false *1: Antenna Cord Sub-assembly (for Type B) 1.156,2.542 5.844,2.865 4.688,0.323 10 false *2: Antenna Cord Sub-assembly (for Type A) 1.156,2.906 5.927,3.26 4.771,0.354 10 false *3: No. 2 Antenna Cord Sub-assembly 1.156,3.26 6.333,3.573 5.177,0.313 10 false *4: No. 5 Antenna Cord Sub-assembly 4.813,0.75 5.125,0.948 0.313,0.198 10 false *2 3.948,1.083 4.469,1.281 0.521,0.198 10 false L 3.938,1.281 5.01,1.521 1.073,0.24 10 false Antenna Divider 3.74,0.479 3.969,0.729 0.229,0.25 10 false 6 4.708,0.469 4.938,0.719 0.229,0.25 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>PRECAUTION

·

When replacing the telematics transceiver, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch ON and wait for 10 seconds or more.


d.

Turn the GTS on.


e.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

f.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK MODEL
2.CHECK MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
w/o Antenna Divider A
w/ Antenna Divider B




A

3.INSPECT NO. 5 ANTENNA CORD SUB-ASSEMBLY

B

9.INSPECT NO. 5 ANTENNA CORD SUB-ASSEMBLY
3.INSPECT NO. 5 ANTENNA CORD SUB-ASSEMBLY
a.
E271898C37
2.313,0.99 2.729,1.24 0.417,0.25 1.219,0.885 1.552,0.885 false 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 2.479,1.042 2.792,1.24 0.313,0.198 10 false K 1.01,0.802 1.323,1 0.313,0.198 10 false 2a
*a Component without harness connected (No. 5 Antenna Cord Sub-assembly)


Disconnect the K No. 5 antenna cord sub-assembly connector.


b.
E170182C57
1.625,0.177 1.958,0.375 0.333,0.198 1.135,0.625 1.542,0.979 false 0.917,0.5 1.229,0.698 0.313,0.198 10 false 2a 1.76,0.198 1.917,0.396 0.156,0.198 10 false J 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a
*a Component without harness connected (No. 5 Antenna Cord Sub-assembly)


Disconnect the J No. 5 antenna cord sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K-2 - J-2 Always Below 1 Ω
K-2 or J-2 - Body ground Always 10 kΩ or higher
K-2a - J-2a Always Below 1 Ω
K-2a or J-2a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 5 ANTENNA CORD SUB-ASSEMBLY

4.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
B278874C39
1.563,0.281 1.865,0.521 0.302,0.24 2.531,0.385 2.063,0.781 false 2.563,0.281 2.875,0.479 0.313,0.198 10 false 2a 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 1.698,0.333 1.854,0.531 0.156,0.198 10 false I
*a Component without harness connected (No. 2 Antenna Cord Sub-assembly)


Disconnect the I No. 2 antenna cord sub-assembly connector.


b.
E432126C16
1.615,0.229 1.917,0.438 0.302,0.208 2.448,1.677 2.188,1.219 false 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 2.49,1.719 2.802,1.917 0.313,0.198 10 false 2a 1.719,0.25 1.875,0.448 0.156,0.198 10 false H
*a Component without harness connected (No. 2 Antenna Cord Sub-assembly)


Disconnect the H No. 2 antenna cord sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I-2 - H-2 Always Below 1 Ω
I-2 or H-2 - Body ground Always 10 kΩ or higher
I-2a - H-2a Always Below 1 Ω
I-2a or H-2a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Type A)

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

5.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Type A)
a.
E372424C41
1.583,0.396 1.865,0.604 0.281,0.208 1.313,1.24 1.083,1.74 false 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.938,1.75 1.25,1.948 0.313,0.198 10 false 2a 1.677,0.427 1.833,0.625 0.156,0.198 10 false G
*a Component without harness connected (Antenna Cord Sub-assembly (for Type A))


Disconnect the G antenna cord sub-assembly (for Type A) connector.


b.
E452653C02
1.583,0.417 1.885,0.625 0.302,0.208 1.24,1.667 1.406,1.365 false 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.135,1.688 1.448,1.885 0.313,0.198 10 false 1a 1.677,0.448 1.833,0.646 0.156,0.198 10 false E
*a Component without harness connected (Antenna Cord Sub-assembly (for Type A))


Disconnect the E antenna cord sub-assembly (for Type A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G-2 - E-1 Always Below 1 Ω
G-2 or E-1 - Body ground Always 10 kΩ or higher
G-2a - E-1a Always Below 1 Ω
G-2a or E-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Type B)

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY (for Type A)

6.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Type B)
a.
E215788C95
1.563,0.406 1.875,0.625 0.313,0.219 2.042,1.365 2.146,1.677 false 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 2.198,1.719 2.51,1.917 0.313,0.198 10 false 1a 1.677,0.438 1.833,0.635 0.156,0.198 10 false D
*a Component without harness connected (Antenna Cord Sub-assembly (for Type B))


Disconnect the D antenna cord sub-assembly (for Type B) connector.


b.
E418544C19
1.542,0.177 1.958,0.427 0.417,0.25 0.917,1.646 1.531,1.417 false 1.708,0.24 1.865,0.438 0.156,0.198 10 false B 0.646,1.563 0.979,1.76 0.333,0.198 10 false 1a 0.167,0.146 0.365,0.323 0.198,0.177 10 false *a
*a Component without harness connected (Antenna Cord Sub-assembly (for Type B))


Disconnect the B antenna cord sub-assembly (for Type B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D-1 - B-1 Always Below 1 Ω
D-1 or B-1 - Body ground Always 10 kΩ or higher
D-1a - B-1a Always Below 1 Ω
D-1a or B-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE ROOF ANTENNA ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY (for Type B)

7.REPLACE ROOF ANTENNA ASSEMBLY
a.

Replace the roof antenna assembly with a new or known good one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL


b.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

8.REPLACE TELEMATICS TRANSCEIVER
8.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.INSPECT NO. 5 ANTENNA CORD SUB-ASSEMBLY
a.
E271898C37
2.313,0.99 2.729,1.24 0.417,0.25 1.219,0.885 1.552,0.885 false 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 2.479,1.042 2.792,1.24 0.313,0.198 10 false K 1.01,0.802 1.323,1 0.313,0.198 10 false 2a
*a Component without harness connected (No. 5 Antenna Cord Sub-assembly)


Disconnect the K No. 5 antenna cord sub-assembly connector.


b.
E170182C57
1.625,0.177 1.958,0.375 0.333,0.198 1.135,0.625 1.542,0.979 false 0.917,0.5 1.229,0.698 0.313,0.198 10 false 2a 1.76,0.198 1.917,0.396 0.156,0.198 10 false J 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a
*a Component without harness connected (No. 5 Antenna Cord Sub-assembly)


Disconnect the J No. 5 antenna cord sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K-2 - J-2 Always Below 1 Ω
K-2 or J-2 - Body ground Always 10 kΩ or higher
K-2a - J-2a Always Below 1 Ω
K-2a or J-2a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 5 ANTENNA CORD SUB-ASSEMBLY

10.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
B278874C39
1.563,0.281 1.865,0.521 0.302,0.24 2.531,0.385 2.063,0.781 false 2.563,0.281 2.875,0.479 0.313,0.198 10 false 2a 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 1.698,0.333 1.854,0.531 0.156,0.198 10 false I
*a Component without harness connected (No. 2 Antenna Cord Sub-assembly)


Disconnect the I No. 2 antenna cord sub-assembly connector.


b.
E432126C16
1.615,0.229 1.917,0.438 0.302,0.208 2.448,1.677 2.188,1.219 false 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 2.49,1.719 2.802,1.917 0.313,0.198 10 false 2a 1.719,0.25 1.875,0.448 0.156,0.198 10 false H
*a Component without harness connected (No. 2 Antenna Cord Sub-assembly)


Disconnect the H No. 2 antenna cord sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I-2 - H-2 Always Below 1 Ω
I-2 or H-2 - Body ground Always 10 kΩ or higher
I-2a - H-2a Always Below 1 Ω
I-2a or H-2a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Type A)

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

11.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Type A)
a.
E372424C51
1.583,0.396 1.865,0.604 0.281,0.208 1.313,1.24 1.083,1.74 false 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.938,1.75 1.25,1.948 0.313,0.198 10 false 2a 1.677,0.427 1.833,0.625 0.156,0.198 10 false G
*a Component without harness connected
(Antenna Cord Sub-assembly (for Type A))


Disconnect the G antenna cord sub-assembly (for Type A) connector.


b.
E372424C52
1.521,0.354 1.896,0.583 0.375,0.229 2.115,1.656 2.115,1.219 false 2.458,1.656 2.458,1.219 false 0.146,0.167 0.458,0.365 0.313,0.198 10 false *a 1.656,0.385 1.813,0.583 0.156,0.198 10 false L 2.031,1.677 2.344,1.875 0.313,0.198 10 false 5a 2.396,1.667 2.708,1.865 0.313,0.198 10 false 6a
*a Component without harness connected
(Antenna Cord Sub-assembly (for Type A))


Disconnect the L antenna cord sub-assembly (for Type A) connector.


c.
E452653C07
1.583,0.417 1.885,0.625 0.302,0.208 1.24,1.667 1.406,1.365 false 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.135,1.688 1.448,1.885 0.313,0.198 10 false 1a 1.677,0.448 1.833,0.646 0.156,0.198 10 false E
*a Component without harness connected
(Antenna Cord Sub-assembly (for Type A))


Disconnect the E antenna cord sub-assembly (for Type A) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G-2 - L-6 Always Below 1 Ω
G-2a - L-6a Always Below 1 Ω
G-2 or L-6 - Body ground Always 10 kΩ or higher
G-2a or L-6a - Body ground Always 10 kΩ or higher
L-5 - E-1 Always Below 1 Ω
L-5a - E-1a Always Below 1 Ω
L-5 or E-1 - Body ground Always 10 kΩ or higher
L-5a or E-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Type B)

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY (for Type A)

12.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Type B)
a.
E215788C95
1.563,0.406 1.875,0.625 0.313,0.219 2.042,1.365 2.146,1.677 false 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 2.198,1.719 2.51,1.917 0.313,0.198 10 false 1a 1.677,0.438 1.833,0.635 0.156,0.198 10 false D
*a Component without harness connected (Antenna Cord Sub-assembly (for Type B))


Disconnect the D antenna cord sub-assembly (for Type B) connector.


b.
E418544C19
1.542,0.177 1.958,0.427 0.417,0.25 0.917,1.646 1.531,1.417 false 1.708,0.24 1.865,0.438 0.156,0.198 10 false B 0.646,1.563 0.979,1.76 0.333,0.198 10 false 1a 0.167,0.146 0.365,0.323 0.198,0.177 10 false *a
*a Component without harness connected (Antenna Cord Sub-assembly (for Type B))


Disconnect the B antenna cord sub-assembly (for Type B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D-1 - B-1 Always Below 1 Ω
D-1 or B-1 - Body ground Always 10 kΩ or higher
D-1a - B-1a Always Below 1 Ω
D-1a or B-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.INSPECT ANTENNA DIVIDER

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY (for Type B)

13.INSPECT ANTENNA DIVIDER
a.

b.
E241596C09
1.125,1.417 0.979,1.76 0.979,1.76 0.781,1.76 true 1.406,1.427 1.49,1.771 1.49,1.771 1.74,1.771 true 0.573,1.677 1,1.854 0.427,0.177 10 false 6a 1.813,1.688 2.24,1.865 0.427,0.177 10 false 5a 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a
*a Component without harness connected
(Antenna Divider)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 6 Always 10 kΩ or higher
5 - 6 Always Below 1 Ω
5 - 5a Always 10 kΩ or higher
6 - 6a Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.REPLACE ROOF ANTENNA ASSEMBLY

NG

14.REPLACE ROOF ANTENNA ASSEMBLY
a.

Replace the roof antenna assembly with a new or known good one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL


b.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 233

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

15.REPLACE TELEMATICS TRANSCEIVER
15.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT