Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for ERA-GLONASS) › from 2021.02
RM33A0E _56 Audio / Visual / Telematics _072211 TELEMATICS _0351443 TELEMATICS SYSTEM(for ERA-GLONASS) C

TELEMATICS  TELEMATICS SYSTEM(for ERA-GLONASS)  B15CB11  Telephone Main Antenna Circuit Short to Ground  B15CB13  Telephone Main Antenna Circuit Open  


DESCRIPTION

If an open or short circuit in the roof antenna assembly is detected as a result of a terminal check performed by the telematics transceiver, these DTCs will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15CB11 Telephone Main Antenna Circuit Short to Ground Roof antenna assembly impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON (Short circuit)
·

Telematics transceiver

·

Roof antenna assembly

·

Antenna cord sub-assembly (for Type A)

·

Antenna cord sub-assembly (for Type B)

·

No. 2 antenna cord sub-assembly

·

No. 5 antenna cord sub-assembly


B15CB13 Telephone Main Antenna Circuit Open Roof antenna assembly impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON (Open circuit)
·

Telematics transceiver

·

Roof antenna assembly

·

Antenna cord sub-assembly (for Type A)

·

Antenna cord sub-assembly (for Type B)

·

No. 2 antenna cord sub-assembly

·

No. 5 antenna cord sub-assembly



WIRING DIAGRAM

E342823E44
0.271,1.25 1.156,1.823 0.885,0.573 10 false Roof Antenna Assembly 0.271,1.073 0.427,1.271 0.156,0.198 10 false K 5.99,1.063 6.51,1.26 0.521,0.198 10 false C 6,1.24 6.729,1.802 0.729,0.563 10 false Telematics Transceiver 1.875,0.354 2.104,0.604 0.229,0.25 10 false 3 2.281,0.354 2.51,0.604 0.229,0.25 10 false 3 1.156,0.448 1.385,0.698 0.229,0.25 10 false 4 1.375,0.708 1.688,0.906 0.313,0.198 10 false *4 2.75,0.74 3.063,0.938 0.313,0.198 10 false *3 4.219,0.75 4.531,0.948 0.313,0.198 10 false *2 5.646,0.719 5.958,0.917 0.313,0.198 10 false *1 3.323,0.354 3.552,0.604 0.229,0.25 10 false 5 3.729,0.354 3.958,0.604 0.229,0.25 10 false 5 5.188,0.365 5.417,0.615 0.229,0.25 10 false 2 4.781,0.365 5.01,0.615 0.229,0.25 10 false 2 1.865,0.563 2.021,0.76 0.156,0.198 10 false J 2.292,0.563 2.448,0.76 0.156,0.198 10 false I 3.323,0.573 3.479,0.771 0.156,0.198 10 false H 3.719,0.563 3.875,0.76 0.156,0.198 10 false G 4.771,0.563 4.927,0.76 0.156,0.198 10 false E 5.177,0.563 5.74,0.76 0.563,0.198 10 false D 5.948,0.458 6.177,0.708 0.229,0.25 10 false 1 1.146,2.219 5.885,2.521 4.74,0.302 10 false *1: Antenna Cord Sub-assembly (for Type B) 1.156,2.552 5.844,2.875 4.688,0.323 10 false *2: Antenna Cord Sub-assembly (for Type A) 1.156,2.906 5.927,3.26 4.771,0.354 10 false *3: No. 2 Antenna Cord Sub-assembly 1.156,3.26 6.333,3.573 5.177,0.313 10 false *4: No. 5 Antenna Cord Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>PRECAUTION

·

When replacing the telematics transceiver, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch ON and wait for 10 seconds or more.


d.

Turn the GTS on.


e.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

f.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT ROOF ANTENNA ASSEMBLY
2.INSPECT ROOF ANTENNA ASSEMBLY
a.

Remove the roof antenna assembly.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL


b.
E271865C14
1.969,1.479 2.229,1.729 false 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 2.26,1.708 2.573,1.906 0.313,0.198 10 false 4a
*a Component without harness connected
(Roof Antenna Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 - 4a Always 9 to 11 kΩ



Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 5 ANTENNA CORD SUB-ASSEMBLY

NG

3.INSPECT NO. 5 ANTENNA CORD SUB-ASSEMBLY
a.
E271898C36
2.313,0.99 2.729,1.24 0.417,0.25 1.208,1.094 1.542,1.094 false 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 2.479,1.042 2.792,1.24 0.313,0.198 10 false K 1.01,1.01 1.323,1.208 0.313,0.198 10 false 4a
*a Component without harness connected (No. 5 Antenna Cord Sub-assembly)


Disconnect the K No. 5 antenna cord sub-assembly connector.


b.
E170182C58
1.646,0.177 1.979,0.375 0.333,0.198 2.156,1.833 1.802,1.521 false 2.219,1.823 2.531,2.021 0.313,0.198 10 false 3a 1.781,0.198 1.938,0.396 0.156,0.198 10 false J 0.198,0.219 0.51,0.417 0.313,0.198 10 false *a
*a Component without harness connected (No. 5 Antenna Cord Sub-assembly)


Disconnect the J No. 5 antenna cord sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K-4 - J-3 Always Below 1 Ω
K-4 or J-3 - Body ground Always 10 kΩ or higher
K-4a - J-3a Always Below 1 Ω
K-4a or J-3a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 5 ANTENNA CORD SUB-ASSEMBLY

4.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
B278874C40
1.563,0.281 1.865,0.521 0.302,0.24 1.74,1.542 2.094,1.896 false 2.188,1.844 2.5,2.042 0.313,0.198 10 false 3a 0.25,0.25 0.563,0.448 0.313,0.198 10 false *a 1.698,0.323 1.854,0.521 0.156,0.198 10 false I
*a Component without harness connected (No. 2 Antenna Cord Sub-assembly)


Disconnect the I No. 2 antenna cord sub-assembly connector.


b.
E432126C17
1.563,0.323 1.906,0.573 0.344,0.25 1,1.635 1.417,1.219 false 1.688,0.365 1.844,0.563 0.156,0.198 10 false H 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a 0.833,1.677 1.135,1.938 0.302,0.26 10 false 5a
*a Component without harness connected (No. 2 Antenna Cord Sub-assembly)


Disconnect the H No. 2 antenna cord sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I-3 - H-5 Always Below 1 Ω
I-3 or H-5 - Body ground Always 10 kΩ or higher
I-3a - H-5a Always Below 1 Ω
I-3a or H-5a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Type A)

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

5.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Type A)
a.
E372424C42
1.583,0.396 1.865,0.604 0.281,0.208 2.125,1.24 2.396,1.625 false 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 2.479,1.688 2.792,1.885 0.313,0.198 10 false 5a 1.677,0.427 1.833,0.625 0.156,0.198 10 false G
*a Component without harness connected (Antenna Cord Sub-assembly (for Type A))


Disconnect the G antenna cord sub-assembly (for Type A) connector.


b.
E452653C03
1.583,0.417 1.885,0.625 0.302,0.208 2.01,1.74 1.75,1.365 false 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 2.052,1.75 2.365,1.948 0.313,0.198 10 false 2a 1.677,0.448 1.833,0.646 0.156,0.198 10 false E
*a Component without harness connected (Antenna Cord Sub-assembly (for Type A))


Disconnect the E antenna cord sub-assembly (for Type A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G-5 - E-2 Always Below 1 Ω
G-5 or E-2 - Body ground Always 10 kΩ or higher
G-5a - E-2a Always Below 1 Ω
G-5a or E-2a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Type B)

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY (for Type A)

6.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Type B)
a.
E215788C96
1.563,0.406 1.875,0.625 0.313,0.219 1.75,1.365 2.083,1.74 false 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 2.115,1.729 2.427,1.927 0.313,0.198 10 false 2a 1.677,0.438 1.833,0.635 0.156,0.198 10 false D
*a Component without harness connected (Antenna Cord Sub-assembly (for Type B))


Disconnect the D antenna cord sub-assembly (for Type B) connector.


b.
E418545C20
1.552,0.167 1.969,0.417 0.417,0.25 1.229,1.854 1.604,1.458 false 1.719,0.229 1.875,0.427 0.156,0.198 10 false C 1.021,1.823 1.354,2.021 0.333,0.198 10 false 1a 0.167,0.146 0.365,0.323 0.198,0.177 10 false *a
*a Component without harness connected (Antenna Cord Sub-assembly (for Type B))


Disconnect the C antenna cord sub-assembly (for Type B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D-2 - C-1 Always Below 1 Ω
D-2 or C-1 - Body ground Always 10 kΩ or higher
D-2a - C-1a Always Below 1 Ω
D-2a or C-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE TELEMATICS TRANSCEIVER

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY (for Type B)

7.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT