The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during side No. 1 airbag sensor removal/installation are shown below.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for M20A-FKS: Click hereGeneral>MAINTENANCE>M20A-FKS BATTERY>REMOVAL
for A25A-FKS: Click hereGeneral>MAINTENANCE>A25A-FKS BATTERY>REMOVAL
for 2GR-FKS: Click hereGeneral>MAINTENANCE>2GR-FKS BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
73350C
3.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
for Fold Down Seat Type: Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Fold Down Seat Type)>REMOVAL
for Reclining Seat Type: Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Reclining Seat Type)>REMOVAL
4.REMOVE REAR SEAT CUSHION ASSEMBLY
for Fold Down Seat Type: Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Fold Down Seat Type)>REMOVAL
for Reclining Seat Type: Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Reclining Seat Type)>REMOVAL
72693
5.REMOVE REAR SEAT CUSHION LOCK HOOK
for Fold Down Seat Type: Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Fold Down Seat Type)>REMOVAL
for Reclining Seat Type: Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Reclining Seat Type)>REMOVAL
67914
6.REMOVE FRONT DOOR SCUFF PLATE
62312B
7.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP
Disconnect the front door opening trim weatherstrip to the extent that allows the removal of the lower center pillar garnish.
67918A
8.REMOVE REAR DOOR SCUFF PLATE
62332A
9.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP
Disconnect the rear door opening trim weatherstrip to the extent that allows the removal of the lower center pillar garnish.
62414A
10.REMOVE LOWER CENTER PILLAR GARNISH
89831A
11.REMOVE SIDE NO. 1 AIRBAG SENSOR
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Disconnect the connector from the side No. 1 airbag sensor.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)
| *a | White Housing Lock | *b | Yellow CPA |
| *c | Connector lock is released | - | - |
Push down the white housing lock again and disconnect the connector.
Do not push down the part (A) shown in the illustration when disconnecting the connector.
Remove the bolt and disengage the claw to remove the side No. 1 airbag sensor.
Check that the position of the white housing lock is as shown in the illustration.
| *a | Incorrect | *b | Correct |