Home › Engine / Hybrid System › A25A-FKS (FUEL) › FUEL PUMP (w/o Canister Pump Module) › from 2021.02
RM33A0E _51 Engine / Hybrid System _065343 A25A-FKS FUEL _0341521 FUEL PUMP(w/o Canister Pump Module) A

A25A-FKS FUEL  FUEL PUMP(w/o Canister Pump Module)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Replacement of fuel pump Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 73350C 4.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

Hide 5.REMOVE REAR SEAT CUSHION ASSEMBLY

Hide 72693 6.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 58325E 7.REMOVE REAR FLOOR SERVICE HOLE COVER

a.
A401628C01
0.51,1.146 0.677,1.146 0.677,1.146 0.896,0.854 true 0.333,1.052 0.51,1.229 0.177,0.177 10 true *a
*a Protective Tape


Using a clip remover with its tip wrapped with protective tape, remove the rear floor service hole cover and butyl tape.


b.
A405985

Disconnect the 2 fuel pump connectors.


Hide 77026A 8.DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A405986

Slide the clip and disconnect the No. 1 fuel evaporation tube sub-assembly from the fuel suction tube with pump and gauge assembly.


Hide 77754B 9.DISCONNECT CHARCOAL CANISTER OUTLET HOSE

A406535

a.

Disconnect the charcoal canister outlet hose from the fuel suction tube with pump and gauge assembly.


Hide 10.DISCONNECT FUEL TANK EVAP/VENT TUBE SUB-ASSEMBLY

a.
A406536

Disconnect the fuel tank evap/vent tube sub-assembly from the fuel suction tube with pump and gauge assembly.

Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77209F 11.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A406537C01
0.625,3.844 0.75,3.844 0.75,3.844 0.906,3.479 false 1.229,2.531 1.354,2.531 1.354,2.531 1.5,2.823 false 2.01,2.823 2.156,2.5 2.156,2.5 2.281,2.5 false 1.979,3.313 2.365,3.313 false 1.708,3.625 2.365,3.625 false 1.698,3.469 2.229,3.469 2.229,3.469 2.229,3.625 false 1.292,0.365 1.417,0.365 1.417,0.365 2.104,0.833 true 2.573,0.75 2.813,0.75 true 0.458,3.76 0.771,3.917 0.313,0.156 10 false *1 2.844,0.667 3.042,0.833 0.198,0.167 10 true *2 1.104,0.271 1.281,0.438 0.177,0.167 10 true *3 1.052,2.427 1.365,2.583 0.313,0.156 10 false *a 2.438,3.542 2.75,3.698 0.313,0.156 10 false *b 2.354,2.406 2.667,2.563 0.313,0.156 10 false *c 2.417,3.229 2.615,3.396 0.198,0.167 10 true *2
*1 Fuel Suction Plate Sub-assembly
*2 Tube Joint Clip
*3 Fuel Tank Main Tube Sub-assembly
*a Fuel Tube Joint
*b O-ring
*c Nylon Tube
V100135

Pull off
V100136

Pull off


Remove the tube joint clip, and pull off the fuel tube joint of the fuel tank main tube sub-assembly.

NOTICE:
·

Remove any foreign matter on the fuel tube joint before performing this work.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Be sure to disconnect the fuel tube joint by hand.

·

Do not bend, twist, pinch or kink the nylon tube.

·

Cover the disconnected fuel tube joint with a plastic bag to prevent damage and contamination.

·

If the fuel tube joint and fuel suction plate sub-assembly are stuck, push and pull to release them.




Hide 77144 12.REMOVE FUEL PUMP GAUGE RETAINER

a.
A406538

Disengage the claw to remove the No. 1 fuel tube clamp.


b.

Remove the fuel pump gauge retainer.

i.
A406539C01
0.865,0.385 1.313,0.385 true 0.625,0.875 0.792,0.875 0.792,0.875 0.927,1.042 true 2.01,1.271 2.583,1.271 true 2.083,1.688 2.427,1.688 true 1.24,2.885 1.885,2.885 true 1.938,2.802 2.25,2.958 0.313,0.156 10 false *a 0.427,0.792 0.615,0.958 0.188,0.167 10 true *b 2.479,1.594 2.667,1.76 0.188,0.167 10 true *c 0.688,0.302 0.865,0.458 0.177,0.156 10 true *d 2.625,1.198 2.802,1.354 0.177,0.156 10 true *d
*a Insertion Point
*b SST (Plate)
*c SST (Claw)
*d SST (Bolt)


Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

SST
09808-14031  (09808-01030, 09808-01050)
09808-01071  

HINT:

Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.



ii.

While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).


iii.
A406540C01
0.719,0.427 0.865,0.427 0.865,0.427 1.125,0.854 true 1.125,0.125 1.26,0.125 1.26,0.125 1.479,0.427 true 1.969,1.083 2.344,0.844 2.344,0.844 2.458,0.844 true 2.135,1.25 2.552,1.25 true 1.302,2.385 2,2.385 true 0.51,0.333 0.698,0.5 0.188,0.167 10 true *a 2.604,1.167 2.771,1.323 0.167,0.156 10 true *b 1.125,2.302 1.438,2.458 0.313,0.156 10 false *c 0.948,0.052 1.26,0.208 0.313,0.156 10 false *d 2.5,0.76 2.698,0.917 0.198,0.156 10 true *d
*a SST (Handle)
*b SST (Plate)
*c SST (Claw)
*d SST (Bolt)


Install SST (handle) to SST (plate).

SST
09808-14031  (09808-01010)
09808-01071  


iv.

Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing down on SST, rotate SST (handle) slowly to loosen the fuel pump gauge retainer.

NOTICE:
·

Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank assembly.

·

Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

·

Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.




v.

While pressing down on the fuel suction tube with pump and gauge assembly, remove the fuel pump gauge retainer.



Hide 77020A 13.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.

Remove the fuel suction tube with pump and gauge assembly from the fuel tank assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



b.
A401704

Remove the fuel suction tube set gasket from the fuel tank assembly.