Home › Engine / Hybrid System › A25A-FKS (FUEL) › FUEL SYSTEM › from 2021.02
RM33A0E _51 Engine / Hybrid System _065343 A25A-FKS FUEL _0319391 FUEL SYSTEM L

A25A-FKS FUEL  FUEL SYSTEM  PRECAUTION  


CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A344817

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.

·
A357489

To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.



IGNITION SWITCH EXPRESSIONS


a.

The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.

Expression Ignition Switch (Position) Engine Switch (Condition)
Ignition Switch off LOCK Off (Lock)
Ignition Switch ACC ACC On (ACC)
Ignition Switch ON ON On (IG)
Engine Start START On (Start)



BEFORE WORKING ON FUEL SYSTEM


a.

Before inspecting and repairing the fuel system, disconnect the cable from the negative (-) battery terminal.

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



b.

Do not smoke or work near fire when handling the fuel system.


c.

Keep fuel away from rubber or leather parts.



DISCHARGE FUEL SYSTEM PRESSURE


CAUTION:
·

Make sure the engine coolant temperature is 60°C (140°F) or less when performing this procedure.

·

Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.

·

Pressure will still remain in the fuel lines even after performing the following procedure. When disconnecting a fuel line, cover it with a piece of cloth to prevent fuel from spraying or coming out.



a.

When discharging fuel system pressure by disconnecting the EFI MAIN NO. 2 relay:

i.

Remove the engine room relay block and junction block assembly cover.


ii.

Remove the EFI MAIN NO. 2 relay.


iii.

w/ Cover:

1.

Remove the front wheel opening extension pad LH.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL

2.

Remove the front wheel opening extension pad RH.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL

3.
4.

Remove the No. 2 engine under cover assembly.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL



iv.
A401627C01
0.469,0.625 0.469,0.354 0.469,0.354 0.625,0.354 false 2.417,0.531 2.521,0.313 2.521,0.313 2.677,0.313 false 0.688,0.271 1,0.427 0.313,0.156 10 false *a 2.719,0.219 3.031,0.375 0.313,0.156 10 false *a
*a Lock Lever


Disengage the claw and raise the lock lever to disconnect the No. 6 engine wire connector as shown in the illustration.


v.

Start the engine. After the engine has stopped on its own, turn the ignition switch off.

NOTICE:

Do not increase the engine speed or drive the vehicle while waiting for the engine to stop on its own.



vi.

Crank the engine again and make sure that the engine does not start.

HINT:

DTC P008700 (Fuel Rail / System Pressure - Too Low) and P017100 (System Too Lean) may be stored. Clear the DTCs before proceeding to the next step.




vii.

Remove the fuel tank cap assembly and discharge the pressure from the fuel tank assembly.


viii.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



ix.
A401841C01
0.688,0.542 0.771,0.281 0.771,0.281 0.917,0.281 false 2.292,0.615 2.375,0.354 2.375,0.354 2.521,0.354 false 0.969,0.198 1.281,0.354 0.313,0.156 10 false *a 2.563,0.26 2.875,0.417 0.313,0.156 10 false *a
*a Lock Lever


Connect the No. 6 engine wire connector and push down the lock lever to engage the claw as shown in the illustration.


x.

w/ Cover:

1.

Install the No. 2 engine under cover assembly.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION

3.

Install the front wheel opening extension pad LH.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION

4.

Install the front wheel opening extension pad RH.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION



xi.

Install the EFI MAIN NO. 2 relay.


xii.

Install the engine room relay block and junction block assembly cover.



b.

When discharging fuel system pressure by disconnecting the fuel pump connector:

i.

Remove the rear floor service hole cover.



ii.
A416042C01
0.031,0.042 0.344,0.26 0.313,0.219 12 false *A 0.073,2.438 0.396,2.698 0.323,0.26 12 false *B
*A w/ Canister Pump Module
*B w/o Canister Pump Module


Disconnect the fuel pump connector.


iii.

w/ Cover:

1.

Remove the front wheel opening extension pad LH.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL

2.

Remove the front wheel opening extension pad RH.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL

3.
4.

Remove the No. 2 engine under cover assembly.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL



iv.
A401627C01
0.469,0.625 0.469,0.354 0.469,0.354 0.625,0.354 false 2.417,0.531 2.521,0.313 2.521,0.313 2.677,0.313 false 0.688,0.271 1,0.427 0.313,0.156 10 false *a 2.719,0.219 3.031,0.375 0.313,0.156 10 false *a
*a Lock Lever


Disengage the claw and raise the lock lever to disconnect the No. 6 engine wire connector as shown in the illustration.


v.

Start the engine. After the engine has stopped on its own, turn the ignition switch off.

NOTICE:

Do not increase the engine speed or drive the vehicle while waiting for the engine to stop on its own.



vi.

Crank the engine again and make sure that the engine does not start.

HINT:

DTC P008700 (Fuel Rail / System Pressure - Too Low) and P017100 (System Too Lean) may be stored. Clear the DTCs before proceeding to the next step.




vii.

Remove the fuel tank cap assembly and discharge the pressure from the fuel tank assembly.


viii.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



ix.
A401841C01
0.688,0.542 0.771,0.281 0.771,0.281 0.917,0.281 false 2.292,0.615 2.375,0.354 2.375,0.354 2.521,0.354 false 0.969,0.198 1.281,0.354 0.313,0.156 10 false *a 2.563,0.26 2.875,0.417 0.313,0.156 10 false *a
*a Lock Lever


Connect the No. 6 engine wire connector and push down the lock lever to engage the claw as shown in the illustration.


x.

w/ Cover:

1.

Install the No. 2 engine under cover assembly.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION

3.

Install the front wheel opening extension pad LH.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION

4.

Install the front wheel opening extension pad RH.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION



xi.

Connect the fuel pump connector.


xii.

Install the rear floor service hole cover.





FUEL LINE


a.

When disconnecting a high-pressure fuel line, a large amount of fuel will spray. Perform the following procedure:

i.

Discharge fuel system pressure.


ii.

Disconnect the fuel tube.


iii.

Drain the fuel remaining inside the fuel pump tube into a container.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



b.

Quick Type A:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A401631C01
0,0 0,0 false
V100135

Open
V100136

Pull


Clamp Type A (No. 1 Fuel Pipe Clamp):

Open the cover of the No. 1 fuel pipe clamp and remove the No. 1 fuel pipe clamp from the fuel tube connector.


ii.
A401632

Clamp Type B (Fuel Pipe Clamp):

Remove the fuel pipe clamp from the fuel tube connector.


iii.

Check that there is no foreign matter around the fuel tube connector before disconnecting it. Clean it if necessary.


iv.
A403898C01
1.833,2.344 2.073,2.031 2.073,2.031 2.219,2.031 false 2.271,1.948 2.583,2.104 0.313,0.156 10 false *a
*a Retainer
V100135

Retainer Holding Position
V100136

Pull out


While holding the retainer at the positions shown in the illustration, pull up the retainer to disengage the lock claws.


v.
A403899C01
1.167,0.354 1.313,0.354 1.313,0.354 1.625,0.646 false 1.896,1.948 2.104,1.573 2.104,1.573 2.25,1.573 false 1.979,3.188 2.073,2.938 2.073,2.938 2.219,2.938 false 1.354,3.333 1.604,3.333 1.604,3.333 1.604,3.594 false 2.125,3.885 2.281,4.302 2.281,4.302 2.396,4.302 false 0.833,4.177 0.833,3.917 true 1.875,4.26 1.875,4.063 false 1.479,3.594 1.479,3.333 false 1,0.26 1.313,0.417 0.313,0.156 10 false *a 1.198,3.24 1.51,3.396 0.313,0.156 10 false *b 1.802,4.292 2.115,4.448 0.313,0.156 10 false *c 0.75,4.208 1.063,4.365 0.313,0.156 10 false *d 2.448,4.208 2.76,4.365 0.313,0.156 10 false *e 2.302,1.49 2.615,1.646 0.313,0.156 10 false *a 2.271,2.854 2.583,3.01 0.313,0.156 10 false *a
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Nylon Tube
*e Fuel Pipe
V100135

Retainer Holding Position
V100136

Pull out
V100137

Pull off


Pull up the retainer while holding it at the positions shown in the illustration and pull off the fuel tube connector.


vi.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Do not bend, twist, pinch or kink the nylon tube.




vii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


viii.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



c.

Quick Type A:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A393281C01
1.167,2.354 1.448,2.354 false 1,2.25 1.313,2.406 0.313,0.156 10 false *a
*a Retainer
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe, push the fuel tube connector onto the fuel pipe, then push in the retainer to secure the connection.

NOTICE:

Confirm that the retainer makes a "click" sound when pushed.


HINT:

If it is difficult to push the fuel tube connector onto the fuel pipe, apply a small amount of clean gasoline to the tip of the fuel pipe.



ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.


iii.

Clamp Type A (No. 1 Fuel Pipe Clamp):

Install the No. 1 fuel pipe clamp to the fuel tube connector and close the cover of the No. 1 fuel pipe clamp.


iv.

Clamp Type B (Fuel Pipe Clamp):

Install the fuel pipe clamp to the fuel tube connector.




d.

Quick Type B:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A401634C01
1.938,2.135 2.198,2.135 false 2.125,3.333 2.25,3.083 2.25,3.083 2.375,3.083 false 1.719,3.24 1.833,3.24 1.833,3.24 1.958,3.656 false 2.302,4 2.417,4.302 2.417,4.302 2.531,4.302 false 2.083,4.281 2.083,4.115 false 2.24,2.063 2.552,2.219 0.313,0.156 10 false *a 2.583,4.229 2.896,4.385 0.313,0.156 10 false *b 1.563,3.167 1.875,3.323 0.313,0.156 10 false *d 2.021,4.302 2.333,4.458 0.313,0.156 10 false *c 2.417,3.01 2.729,3.167 0.313,0.156 10 false *a
*a Retainer
*b Fuel Pipe
*c Fuel Tube Connector
*d O-ring
V100135

Pull out
V100136

Pull off


Pull out the retainer to disengage the lock claws and pull off the fuel tube connector.


ii.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has an O-ring that seals the pipe (fuel pipe).



iii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



e.

Quick Type B:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A401635C01
1.865,2.26 1.979,2.052 1.979,2.052 2.156,2.052 false 2.198,1.969 2.51,2.125 0.313,0.156 10 false *a
*a Retainer
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe, push the fuel tube connector onto the fuel pipe, then push in the retainer to secure the connection.

NOTICE:

Confirm that the retainer makes a "click" sound when pushed.


HINT:

If it is difficult to push the fuel tube connector onto the fuel pipe, apply a small amount of clean gasoline to the tip of the fuel pipe.



ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.




f.

Quick Type C:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A310728C01
0.854,3.063 1.073,3.063 1.073,3.063 1.26,2.854 false 2.052,2.75 2.417,2.75 false 0.688,2.979 1,3.135 0.313,0.156 10 false *a 1.885,2.667 2.198,2.823 0.313,0.156 10 false *a
*a Retainer
V100135

Pull out
V100136

Pull off


Pull out the retainer to disengage the lock claws and pull off the fuel tube connector.


ii.
A310289C01
1.979,1.729 1.979,1.302 false 1.656,1.74 2.135,1.74 2.135,1.74 2.135,1.313 false 2.875,1.729 2.875,1.531 2.875,1.531 2.583,1.25 false 2.542,0.917 2.708,0.49 2.708,0.49 2.802,0.49 false 2.052,0.427 2.219,0.427 2.219,0.427 2.375,0.844 false 2.833,0.396 3.146,0.552 0.313,0.156 10 false *a 1.49,1.646 1.802,1.802 0.313,0.156 10 false *b 1.896,0.333 2.208,0.49 0.313,0.156 10 false *c 2.792,1.75 3.021,1.906 0.229,0.156 10 false *d
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Fuel Pipe


If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).



iii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



g.

Quick Type C:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A310729C01
0.844,3.094 1.031,3.094 1.031,3.094 1.271,2.844 false 2.021,2.75 2.406,2.75 false 0.677,3 0.99,3.156 0.313,0.156 10 false *a 1.844,2.656 2.156,2.813 0.313,0.156 10 false *a
*a Retainer
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe, push the fuel tube connector onto the fuel pipe, then push in the retainer to secure the connection.

NOTICE:

Confirm that the retainer makes a "click" sound when pushed.


HINT:

If it is difficult to push the fuel tube connector onto the fuel pipe, apply a small amount of clean gasoline to the tip of the fuel pipe.



ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.




h.

Quick Type D:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A401636C01
1.969,2.24 2.063,1.99 2.063,1.99 2.208,1.99 false 2.188,3.229 2.24,3.01 2.24,3.01 2.406,3.01 false 1.688,3.323 1.969,3.323 1.969,3.323 1.969,3.625 false 1.896,3.625 1.896,3.323 false 2.125,4.469 2.125,4.24 false 2.406,4.135 2.542,4.406 2.542,4.406 2.708,4.406 false 2.271,1.896 2.583,2.052 0.313,0.156 10 false *a 1.521,3.24 1.833,3.396 0.313,0.156 10 false *b 2.042,4.479 2.354,4.635 0.313,0.156 10 false *c 2.76,4.323 3.073,4.479 0.313,0.156 10 false *d 2.448,2.917 2.76,3.073 0.313,0.156 10 false *a
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Fuel Pipe
V100135

Pull out
V100136

Pull off


Pull out the retainer to disengage the lock claws and pull off the fuel tube connector.


ii.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).



iii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



i.

Quick Type D:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A401637C01
2.115,2.448 2.406,2.167 2.406,2.167 2.583,2.167 true 2.635,2.083 2.948,2.24 0.313,0.156 10 false *a 2.344,2.583 2.656,2.74 0.313,0.156 10 false *b 1.833,1.917 2.146,2.073 0.313,0.156 10 false *c 1.583,1.813 1.896,1.969 0.313,0.156 10 false *d 1.896,3.219 2.208,3.375 0.313,0.156 10 false *c
*a Retainer
*b 90°
*c 45°
*d Up
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe, push the fuel tube connector onto the fuel pipe, then push in the retainer to secure the connection.

NOTICE:

Confirm that the retainer makes a "click" sound when pushed.


HINT:
·

If it is difficult to push the fuel tube connector onto the fuel pipe, apply a small amount of clean gasoline to the tip of the fuel pipe.

·

Make sure the retainer is positioned within the area shown in the illustration.




ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.




j.

Quick Type E:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A363273C01
1.958,2.177 1.75,2.177 false 2.042,2.677 1.823,2.885 1.823,2.885 1.698,2.885 true 1.979,3.677 1.979,3.271 1.979,3.271 1.719,3.271 false 2.844,2.854 2.708,2.854 2.708,2.854 2.521,2.667 true 2.719,3.208 2.552,3.208 2.552,3.208 2.375,3.521 false 2.865,4.375 2.729,4.375 2.729,4.375 2.615,4.021 false 2.031,4.135 2.031,4.375 false 1.573,2.073 1.885,2.229 0.313,0.156 10 false *a 2.917,4.302 3.229,4.458 0.313,0.156 10 false *b 1.958,4.385 2.271,4.542 0.313,0.156 10 false *c 1.552,3.188 1.865,3.344 0.313,0.156 10 false *d 1.531,2.792 1.844,2.948 0.313,0.156 10 false *e 2.771,3.125 3.083,3.281 0.313,0.156 10 false *a 2.896,2.771 3.208,2.927 0.313,0.156 10 false *e
*a Retainer
*b Fuel Pipe
*c Fuel Tube Connector
*d O-ring
*e Claw
V100135

Pull
V100136

Pull out
V100137

Pull off


Disengage the 2 claws of the retainer. Pull out the retainer and disconnect the fuel tube connector from the fuel pipe.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



ii.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has an O-ring that seals the pipe (fuel pipe).




iii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



k.

Quick Type E:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A366419C01
2.271,3 2.365,3 2.365,3 2.469,2.885 true 2.198,2.406 2.427,2.406 false 2.979,2.885 3.125,3 3.125,3 3.188,3 true 2.031,2.313 2.344,2.469 0.313,0.156 10 false *a 2.094,2.917 2.406,3.073 0.313,0.156 10 false *b 3.229,2.917 3.427,3.094 0.198,0.177 10 false *b
*a Retainer
*b Claw
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe, push the fuel tube connector onto the fuel pipe, then push in the retainer to engage the 2 claws.

NOTICE:

Confirm that the retainer makes a "click" sound when pushed.


HINT:

If it is difficult to push the fuel tube connector onto the fuel pipe, apply a small amount of clean gasoline to the tip of the fuel pipe.



ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.




l.

Quick Type F:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A318103C02
0.698,2.625 0.854,2.625 0.854,2.625 1.042,3.135 false 0.24,3.021 0.375,3.021 0.375,3.021 0.51,3.333 false 0.99,4.021 0.99,3.75 false 2.146,1.844 2.417,1.844 false 1.865,3.906 1.865,3.583 false 2.49,3.25 2.542,2.938 2.542,2.938 2.656,2.938 false 1.688,3.594 1.688,3.906 1.688,3.906 2.208,3.906 false 2.146,1.573 2.417,1.573 false 2.865,1.563 3.135,1.563 false 1.969,1.76 2.281,1.917 0.313,0.156 10 false *a 0.063,2.948 0.375,3.104 0.313,0.156 10 false *b 2.708,2.865 3.021,3.021 0.313,0.156 10 false *c 0.906,4.052 1.219,4.208 0.313,0.156 10 false *d 2.25,3.833 2.563,3.99 0.313,0.156 10 false *e 0.521,2.542 0.833,2.698 0.313,0.156 10 false *a 3.198,1.5 3.375,1.677 0.177,0.177 10 false *f 2,1.5 2.177,1.677 0.177,0.177 10 false *f
*a Retainer
*b Fuel Pipe
*c Nylon Tube
*d Fuel Tube Connector
*e O-ring
*f Claw
V100135

Push
V100136

Pull out
V100137

Pull off


Disengage the 2 claws of the retainer. Pull out the retainer and disconnect the fuel tube connector from the fuel pipe.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



ii.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Do not bend, twist, pinch or kink the nylon tube.




iii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



m.

Quick Type F:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A303816C02
1.958,1.531 2.365,1.531 false 1.958,1.281 2.365,1.281 false 2.781,1.271 3.188,1.271 false 1.781,1.448 2.094,1.604 0.313,0.156 10 false *a 1.823,1.198 2.135,1.354 0.313,0.156 10 false *b 3.24,1.208 3.427,1.365 0.188,0.156 10 false *b
*a Retainer
*b Claw
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe, push the fuel tube connector onto the fuel pipe, then push in the retainer to engage the 2 claws.

NOTICE:

Confirm that the retainer makes a "click" sound when pushed.


HINT:

If it is difficult to push the fuel tube connector onto the fuel pipe, apply a small amount of clean gasoline to the tip of the fuel pipe.



ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.




n.
A289951C03
2.333,0.427 2.521,0.427 2.521,0.427 2.823,0.74 false 0.917,1.615 1.104,1.615 1.104,1.615 1.365,1.333 false 1.708,1.281 1.906,1.594 1.906,1.594 2.052,1.594 false 2.156,0.354 2.448,0.594 0.292,0.24 10 *a 2.115,1.531 2.438,1.792 0.323,0.26 10 *b 0.698,1.563 1,1.823 0.302,0.26 10 *c
*a Fuel Tube Connector
*b Nylon Tube
*c Ethylene Propylene Diene Monomer (EPDM) Rubber Protector


Observe the following precautions when handling a nylon tube:

NOTICE:
·

Do not twist the nylon tube of the fuel tube connector or fuel tube connector when connecting it.

·

Do not remove the Ethylene Propylene Diene Monomer (EPDM) rubber protector on the outside of the nylon tube.

·

Do not bend, twist, pinch or kink the nylon tube.





FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY


NOTICE:
·

Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube with pump and gauge assembly. Doing so will cause reassembly of the fuel suction tube with pump and gauge assembly to be impossible as the tube is pressed into the fuel suction plate sub-assembly.

·

When replacing the fuel filter, replace it together with the fuel suction plate sub-assembly.


A502657C01
0.177,0.104 7.042,1.875 6.865,1.771 0.177,1.875 7.042,3.771 6.865,1.896 0.667,1.917 3.646,3.719 2.979,1.802 3.646,1.917 6.625,3.719 2.979,1.802 2.802,1.146 3.396,1.146 true 4.781,3.125 5.375,3.125 true 1.198,3.135 1.792,3.135 true 0.229,0.177 0.656,0.563 0.427,0.385 12 false *A 0.24,1.969 0.646,2.292 0.406,0.323 12 false *B 0.854,1.979 1.115,2.188 0.26,0.208 12 false *C 4.052,1.99 4.448,2.344 0.396,0.354 12 false *D 2.615,1.052 3.042,1.438 0.427,0.385 10 false *a 4.625,3.021 5.052,3.406 0.427,0.385 10 false *a 1.021,3.042 1.448,3.427 0.427,0.385 10 false *a
*A w/ Canister Pump Module *B w/o Canister Pump Module
*C for Type A *D for Type B
*a Tube - -




INSPECT FOR FUEL LEAK


a.

Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs.

Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION