The outer mirror switch assembly sends the retractable outer mirror switch signal to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) then sends the mirror retract/return signal to each outer mirror control ECU assembly via CAN communication. Based on the signal, each outer mirror control ECU assembly retracts or returns its corresponding outer rear view mirror assembly.
The power mirror control system (w/ Memory) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power mirror control system (w/ Memory) after confirming that the communication systems are functioning properly.
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Outer Mirror Fold SW | Retractable outer mirror switch signal | OFF or ON | OFF: Retractable outer mirror switch not in retract position
ON: Retractable outer mirror switch in retract position |
- |
| Tester Display |
|---|
| Outer Mirror Fold SW |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Enter the following menus: Body Electrical / Mirror L or Mirror R / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Mirror Fold/Return | Mirror retract operation | OFF, Return or Fold | ·
Operate with the engine switch on (IG) and the vehicle stopped. ·
This test activates the Fold / Return. ·
This operation can be confirmed by watching the mirror move in the desired direction. |
| Tester Display |
|---|
| Mirror Fold/Return |
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Mirror Fold/Return | Mirror retract operation | OFF, Return or Fold | ·
Operate with the engine switch on (IG) and the vehicle stopped. ·
This test activates the Fold / Return. ·
This operation can be confirmed by watching the mirror move in the desired direction. |
| Tester Display |
|---|
| Mirror Fold/Return |
| Result | Proceed to |
|---|---|
| Outer rear view mirror assemblies operate normally | A |
| Outer rear view mirror assembly (driver door) does not operate normally | B |
| Outer rear view mirror assembly (front passenger door) does not operate normally | C |
A
B
C
Disconnect the O9 outer mirror control ECU assembly (driver door) connector.
Disconnect the O21*1 or O22*2 outer rear view mirror assembly (driver door) connector.
*1: for 16 Pin Connector
*2: for 22 Pin Connector
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O9-3 (MR+) - O21-3 (MR) | Always | Below 1 Ω |
| O9-11 (MR-) - O21-11 (MF) | Always | Below 1 Ω |
| O9-3 (MR+) or O21-3 (MR) - Body ground | Always | 10 kΩ or higher |
| O9-11 (MR-) or O21-11 (MF) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O9-3 (MR+) - O22-19 (MR) | Always | Below 1 Ω |
| O9-11 (MR-) - O22-20 (MF) | Always | Below 1 Ω |
| O9-3 (MR+) or O22-19 (MR) - Body ground | Always | 10 kΩ or higher |
| O9-11 (MR-) or O22-20 (MF) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the outer rear view mirror assembly (driver door).
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL
Inspect the outer rear view mirror assembly (driver door)(retractable mirror).
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the outer mirror control ECU assembly (driver door) with a new or known good one.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the power retract mirror function operates normally.
Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>OPERATION CHECK
Power retract mirror function operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N10 outer mirror control ECU assembly (front passenger door) connector.
Disconnect the N23*1 or N24*2 outer rear view mirror assembly (front passenger door) connector.
*1: for 16 Pin Connector
*2: for 22 Pin Connector
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N10-3 (MR+) - N23-3 (MR) | Always | Below 1 Ω |
| N10-11 (MR-) - N23-11 (MF) | Always | Below 1 Ω |
| N10-3 (MR+) or N23-3 (MR) - Body ground | Always | 10 kΩ or higher |
| N10-11 (MR-) or N23-11 (MF) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N10-3 (MR+) - N24-19 (MR) | Always | Below 1 Ω |
| N10-11 (MR-) - N24-20 (MF) | Always | Below 1 Ω |
| N10-3 (MR+) or N24-19 (MR) - Body ground | Always | 10 kΩ or higher |
| N10-11 (MR-) or N24-20 (MF) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the outer rear view mirror assembly (front passenger door).
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL
Inspect the outer rear view mirror assembly (front passenger door)(retractable mirror).
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the outer mirror control ECU assembly (front passenger door) with a new or known good one.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the power retract mirror function operates normally.
Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>OPERATION CHECK
Power retract mirror function operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the outer mirror switch assembly.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>REMOVAL
Inspect the outer mirror switch assembly.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O26 outer mirror switch assembly.
Disconnect the K53 main body ECU (multiplex network body ECU).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O26-10 (MR) - K53-16 (RET) | Always | Below 1 Ω |
| O26-10 (MR) or K53-16 (RET) - Body ground | Always | 10 kΩ or higher |
| O26-9 (MAT) - K53-6 (AMR) | Always | Below 1 Ω |
| O26-9 (MAT) or K53-6 (AMR) - Body ground | Always | 10 kΩ or higher |
| O26-8 (E2) - K53-9 (MIRE) | Always | Below 1 Ω |
| O26-8 (E2) or K53-9 (MIRE) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG