The outer mirror switch assembly sends a mirror retract/return signal to the main body ECU (multiplex network body ECU) when the retractable outer mirror switch on the outer mirror switch assembly is operated. The main body ECU (multiplex network body ECU) retracts or returns the outer rear view mirror assemblies based on the signal.
Inspect the fuses for circuits related to this system before performing the following procedure.
If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Outer Mirror Fold SW | Retractable outer mirror switch signal | OFF or ON | OFF: Retractable outer mirror switch not in retract position
ON: Retractable outer mirror switch in retract position |
- |
| Tester Display |
|---|
| Outer Mirror Fold SW |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the malfunctioning parts.
| Result | Proceed to |
|---|---|
| Both outer rear view mirror assemblies are malfunctioning | A |
| Outer rear view mirror assembly LH is malfunctioning | B |
| Outer rear view mirror assembly RH is malfunctioning | C |
A
B
C
Inspect the MIR MTR NO. 1 relay.
Click hereVehicle Exterior>MIRROR (EXT)>RELAY>ON-VEHICLE INSPECTION
Inspect the MIR MTR NO. 2 relay.
Click hereVehicle Exterior>MIRROR (EXT)>RELAY>ON-VEHICLE INSPECTION
| Result | Proceed to |
|---|---|
| OK | A |
| NG (MIR MTR NO. 1 Relay) | B |
| NG (MIR MTR NO. 2 Relay) | C |
A
B
C
| *1 | No. 6 Relay Block Assembly |
| *a | MIR MTR NO. 2 Relay terminals |
| *b | MIR MTR NO. 1 Relay terminals |
Remove the MIR MTR NO. 1 relay from the No. 6 relay block assembly.
Remove the MIR MTR NO. 2 relay from the No. 6 relay block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 6 relay block assembly MIR MTR NO. 1 relay terminal 1 - Body ground | Always | 11 to 14 V |
| No. 6 relay block assembly MIR MTR NO. 2 relay terminal 1 - Body ground | Always | 11 to 14 V |
| No. 6 relay block assembly MIR MTR NO. 1 relay terminal 5 - Body ground | Always | 11 to 14 V |
| No. 6 relay block assembly MIR MTR NO. 2 relay terminal 5 - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 6 relay block assembly MIR MTR NO. 1 relay terminal 4 - Body ground | Always | Below 1 Ω |
| No. 6 relay block assembly MIR MTR NO. 2 relay terminal 4 - Body ground | Always | Below 1 Ω |
| No. 6 relay block assembly MIR MTR NO. 1 relay terminal 4 - No. 6 relay block assembly MIR MTR NO. 2 relay terminal 4 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 6 Relay Block Assembly |
| *a | MIR MTR NO. 2 Relay terminals |
| *b | MIR MTR NO. 1 Relay terminals |
Remove the MIR MTR NO. 1 relay from the No. 6 relay block assembly.
Remove the MIR MTR NO. 2 relay from the No. 6 relay block assembly.
Disconnect the K52 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 6 relay block assembly MIR MTR NO. 2 relay terminal 2 - K52-10 (RETR) | Always | Below 1 Ω |
| No. 6 relay block assembly MIR MTR NO. 1 relay terminal 2 - K52-11 (RTRR) | Always | Below 1 Ω |
| No. 6 relay block assembly MIR MTR NO. 2 relay terminal 2 or K52-10 (RETR) - Body Ground | Always | 10 kΩ or higher |
| No. 6 relay block assembly MIR MTR NO. 1 relay terminal 2 or K52-11 (RTRR) - Body Ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 6 Relay Block Assembly |
| *a | MIR MTR NO. 2 Relay terminals |
| *b | MIR MTR NO. 1 Relay terminals |
Remove the MIR MTR NO. 1 relay from the No. 6 relay block assembly.
Remove the MIR MTR NO. 2 relay from the No. 6 relay block assembly.
Disconnect the O16*1 or O20*2 outer rear view mirror assembly LH connector.
Disconnect the N19*1 or N22*2 outer rear view mirror assembly RH connector.
Measure the resistance according to the value(s) in the table below.
*1: w/ Mirror Heater
*2: w/o Mirror Heater
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 6 relay block assembly MIR MTR NO. 2 relay terminal 3 - N19-3 (MR) | Always | Below 1 Ω |
| No. 6 relay block assembly MIR MTR NO. 2 relay terminal 3 - O16-3 (MR) | Always | Below 1 Ω |
| No. 6 relay block assembly MIR MTR NO. 1 relay terminal 3 - N19-9 (MF) | Always | Below 1 Ω |
| No. 6 relay block assembly MIR MTR NO. 1 relay terminal 3 - O16-9 (MF) | Always | Below 1 Ω |
| No. 6 relay block assembly MIR MTR NO. 2 relay terminal 3 or N19-3 (MR) - Body Ground | Always | 10 kΩ or higher |
| No. 6 relay block assembly MIR MTR NO. 2 relay terminal 3 or O16-3 (MR) - Body Ground | Always | 10 kΩ or higher |
| No. 6 relay block assembly MIR MTR NO. 1 relay terminal 3 or N19-9 (MF) - Body Ground | Always | 10 kΩ or higher |
| No. 6 relay block assembly MIR MTR NO. 1 relay terminal 3 or O16-9 (MF) - Body Ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 6 relay block assembly MIR MTR NO. 2 relay terminal 3 - N22-1 (MR) | Always | Below 1 Ω |
| No. 6 relay block assembly MIR MTR NO. 2 relay terminal 3 - O20-1 (MR) | Always | Below 1 Ω |
| No. 6 relay block assembly MIR MTR NO. 1 relay terminal 3 - N22-2 (MF) | Always | Below 1 Ω |
| No. 6 relay block assembly MIR MTR NO. 1 relay terminal 3 - O20-2 (MF) | Always | Below 1 Ω |
| No. 6 relay block assembly MIR MTR NO. 2 relay terminal 3 or N22-1 (MR) - Body Ground | Always | 10 kΩ or higher |
| No. 6 relay block assembly MIR MTR NO. 2 relay terminal 3 or O20-1 (MR) - Body Ground | Always | 10 kΩ or higher |
| No. 6 relay block assembly MIR MTR NO. 1 relay terminal 3 or N22-2 (MF) - Body Ground | Always | 10 kΩ or higher |
| No. 6 relay block assembly MIR MTR NO. 1 relay terminal 3 or O20-2 (MF) - Body Ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the outer rear view mirror assembly LH.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL
Inspect the outer rear view mirror assembly LH.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 6 Relay Block Assembly |
| *a | MIR MTR NO. 2 Relay terminals |
| *b | MIR MTR NO. 1 Relay terminals |
Remove the MIR MTR NO. 1 relay from the No. 6 relay block assembly.
Remove the MIR MTR NO. 2 relay from the No. 6 relay block assembly.
Disconnect the O16*1 or O20*2 outer rear view mirror assembly LH connector.
Measure the resistance according to the value(s) in the table below.
*1: w/ Mirror Heater
*2: w/o Mirror Heater
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 6 relay block assembly MIR MTR NO. 2 relay terminal 3 - O16-3 (MR) | Always | Below 1 Ω |
| No. 6 relay block assembly MIR MTR NO. 1 relay terminal 3 - O16-9 (MF) | Always | Below 1 Ω |
| No. 6 relay block assembly MIR MTR NO. 2 relay terminal 3 or O16-3 (MR) - Body Ground | Always | 10 kΩ or higher |
| No. 6 relay block assembly MIR MTR NO. 1 relay terminal 3 or O16-9 (MF) - Body Ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 6 relay block assembly MIR MTR NO. 2 relay terminal 3 - O20-1 (MR) | Always | Below 1 Ω |
| No. 6 relay block assembly MIR MTR NO. 1 relay terminal 3 - O20-2 (MF) | Always | Below 1 Ω |
| No. 6 relay block assembly MIR MTR NO. 2 relay terminal 3 or O20-1 (MR) - Body Ground | Always | 10 kΩ or higher |
| No. 6 relay block assembly MIR MTR NO. 1 relay terminal 3 or O20-2 (MF) - Body Ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Remove the outer rear view mirror assembly RH.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL
Inspect the outer rear view mirror assembly RH.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 6 Relay Block Assembly |
| *a | MIR MTR NO. 2 Relay terminals |
| *b | MIR MTR NO. 1 Relay terminals |
Remove the MIR MTR NO. 1 relay from the No. 6 relay block assembly.
Remove the MIR MTR NO. 2 relay from the No. 6 relay block assembly.
Disconnect the N19*1 or N22*2 outer rear view mirror assembly RH connector.
Measure the resistance according to the value(s) in the table below.
*1: w/ Mirror Heater
*2: w/o Mirror Heater
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 6 relay block assembly MIR MTR NO. 2 relay terminal 3 - N19-3 (MR) | Always | Below 1 Ω |
| No. 6 relay block assembly MIR MTR NO. 1 relay terminal 3 - N19-9 (MF) | Always | Below 1 Ω |
| No. 6 relay block assembly MIR MTR NO. 2 relay terminal 3 or N19-3 (MR) - Body Ground | Always | 10 kΩ or higher |
| No. 6 relay block assembly MIR MTR NO. 1 relay terminal 3 or N19-9 (MF) - Body Ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 6 relay block assembly MIR MTR NO. 2 relay terminal 3 - N22-1 (MR) | Always | Below 1 Ω |
| No. 6 relay block assembly MIR MTR NO. 1 relay terminal 3 - N22-2 (MF) | Always | Below 1 Ω |
| No. 6 relay block assembly MIR MTR NO. 2 relay terminal 3 or N22-1 (MR) - Body Ground | Always | 10 kΩ or higher |
| No. 6 relay block assembly MIR MTR NO. 1 relay terminal 3 or N22-2 (MF) - Body Ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Remove the outer mirror switch assembly.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>REMOVAL
Inspect the outer mirror switch assembly.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O26 outer mirror switch assembly.
Disconnect the K53 main body ECU (multiplex network body ECU).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O26-10 (MR) - K53-16 (RET) | Always | Below 1 Ω |
| O26-9 (MAT) - K53-6 (AMR) | Always | Below 1 Ω |
| O26-10 (MR) or K53-16 (RET) - Body ground | Always | 10 kΩ or higher |
| O26-9 (MAT) or K53-6 (AMR) - Body ground | Always | 10 kΩ or higher |
| O26-8 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG