47070
1.INSTALL BRAKE BOOSTER PUMP ASSEMBLY
| *1 | Brake Booster Pump Collar |
| *2 | Brake Booster Pump Bushing |
Install the 2 brake booster pump collars and 2 brake booster pump bushings to the brake booster pump assembly as shown in the illustration.
Perform this procedure only when replacement of the brake booster pump collars or brake booster pump bushings is necessary.
| *1 | Brake Booster Pump Collar |
| *2 | Brake Booster Pump Bushing |
| *a | Union |
| *b | Connector |
| *c | Wire Harness |
| *d | Stud |
Install the brake booster pump assembly, brake booster pump bushing and brake actuator case collar to the brake actuator bracket assembly.
Do not drop the brake booster pump assembly when carrying it.
Be careful not to allow brake fluid to enter the connector.
When installing the brake booster pump assembly to the brake actuator bracket assembly, confirm that the 2 brake booster pump bushings and 2 brake booster pump collars are installed to the brake booster pump assembly.
If installing a new brake booster pump assembly, do not remove the hole plugs before connecting the brake lines because the brake booster pump assembly is filled with brake fluid.
Do not carry the brake booster pump assembly by the parts shown in the illustration.
Install the nut.
Engage the claw and clamp to install the brake booster pump assembly wire harness to the brake actuator bracket assembly.
Engage the claw and clamp in the order shown in the illustration.
44572C
2.INSTALL NO. 2 BRAKE ACTUATOR HOSE
| *a | Identification Mark |
|
Front of the vehicle |
Install the No. 2 brake actuator hose to the brake booster pump assembly and slide the clip to secure it.
When connecting the No. 2 brake actuator hose, face the identification mark up.
Install the clip within the range shown in the illustration.
3.INSTALL BRAKE ACTUATOR WITH BRAKE BOOSTER PUMP ASSEMBLY
Temporarily install the brake actuator with brake booster pump assembly to the vehicle body as shown in the illustration.
| *1 | Brake Actuator Bracket Assembly | - | - |
| *a | Cutout | - | - |
Do not kink or damage the brake lines.
Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
Be careful not to allow any brake fluid to enter the connector.
Do not hold the brake booster pump assembly by the connector, union or wire harness.
Do not hold the brake actuator assembly by the connector.
Do not drop the brake actuator with brake booster pump assembly when carrying it.
When temporarily installing the brake actuator with brake booster pump assembly, pass the brake actuator bracket assembly through the cutout in the vehicle body.
Return each brake line to its original position.
Install the brake actuator with brake booster pump assembly to the vehicle body with the 2 bolts and nut.
| *a | Torque Wrench Fulcrum Length | *b | Bolt (A) |
| *c | Bolt (B) | - | - |
Tighten the 2 bolts and nut in the order shown in the illustration.
Make sure to use SST when tightening the bolt (B).
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using SST (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
Bolt (B): 9.9 N*m (101 kgf*cm, 88 in.*lbf)
Tighten the bolt (A) from the bottom of the vehicle.
Remove the protective tape.
| *A | Type A |
| *B | Type B |
Type A:
Engage the 6 clamps to install a new No. 2 brake tube clamp to the brake lines.
Do not kink or damage the brake lines.
Type B:
Engage the 5 clamps to install a new No. 2 brake tube clamp to the brake lines.
Do not kink or damage the brake lines.
Engage the clamp and install the No. 2 brake tube clamp to the vehicle body.
Do not kink or damage the brake lines.
Install the front brake tube way to the vehicle body with the bolt.
Engage the clamp to install a new brake tube clamp.
Return the front No. 5 brake tube to its original position.
Do not apply excessive force to the front No. 5 brake tube.
Temporarily install the front No. 5 brake tube to the front flexible hose.
Do not kink or damage the front No. 5 brake tube.
Do not allow any foreign matter such as dirt or dust to enter the front No. 5 brake tube from the connecting parts.
Engage the clamp to connect the front No. 5 brake tube.
Do not kink or damage the front No. 5 brake tube.
| *a | From 1st Chamber of Brake Booster with Master Cylinder Assembly |
| *b | From 2nd Chamber of Brake Booster with Master Cylinder Assembly |
| *c | To Front Wheel Cylinder Assembly LH |
| *d | To Rear Wheel Cylinder Assembly RH |
| *e | To Rear Wheel Cylinder Assembly LH |
| *f | To Front Wheel Cylinder Assembly RH |
Temporarily tighten the 6 brake lines to the correct positions on the brake actuator assembly as shown in the illustration.
Do not kink or damage the brake lines.
Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
| *a | Torque Wrench Fulcrum Length |
| *b | Union Nut Wrench |
Using a union nut wrench, fully tighten the 6 brake lines.
Do not kink or damage the brake lines.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
13.4 N*m (137 kgf*cm, 10 ft.*lbf)
| *a | Torque Wrench Fulcrum Length |
| *b | Union Nut Wrench |
Using a union nut wrench, fully tighten the front No. 5 brake tube while holding the front flexible hose with a wrench.
Do not kink or damage the front No. 5 brake tube.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
13.4 N*m (137 kgf*cm, 10 ft.*lbf)
|
Connect the connector |
|
Lock the lock lever |
Connect the connector to the brake actuator assembly and lock the lock lever as shown in the illustration.
Make sure that the connector is locked securely.
Make sure that the connector can be connected smoothly.
Do not allow water, oil or dirt to enter the connector.
Engage the clamp to install the engine room main wire.
|
Connect the connector |
|
Lock the lock lever |
Connect the connector to the brake booster pump assembly and lock the lock lever as shown in the illustration.
Make sure that the connector is locked securely.
Make sure that the connector can be connected smoothly.
Do not allow water, oil or dirt to enter the connector.
473A1
4.CONNECT ACCUMULATOR TO BRAKE MASTER CYLINDER TUBE
| *a | Torque Wrench Fulcrum Length |
| *b | Union Nut Wrench |
Using a union nut wrench, connect the accumulator to brake master cylinder tube to the brake booster pump assembly.
Do not kink or damage the accumulator to brake master cylinder tube.
Do not allow the accumulator to brake master cylinder tube to twist or interfere with other parts or the vehicle body during tightening.
Do not allow any foreign matter such as dirt or dust to enter the accumulator to brake master cylinder tube from the connecting parts.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
13.4 N*m (137 kgf*cm, 10 ft.*lbf)
44572C
5.CONNECT NO. 2 BRAKE ACTUATOR HOSE
| *a | Identification Mark |
|
Front of the vehicle |
Connect the No. 2 brake actuator hose to the No. 1 brake actuator tube and slide the clip to secure it.
When connecting the No. 2 brake actuator hose, face the identification mark up.
Install the clip within the range shown in the illustration.
89661
6.INSTALL ECM
44551C
7.BLEED NO. 1 BRAKE ACTUATOR TUBE
8.FILL RESERVOIR WITH BRAKE FLUID
9.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
10.BLEED BRAKE SYSTEM
53607A
11.INSTALL FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY
55708
12.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
13.INSTALL FRONT WHEEL LH