Home › Drivetrain › P710 (HYBRID TRANSMISSION / TRANSAXLE) › SHIFT LEVER POSITION SENSOR
RM33C0E _52 Drivetrain _065428 P710 HYBRID TRANSMISSION / TRANSAXLE _0319559 SHIFT LEVER POSITION SENSOR A

P710 HYBRID TRANSMISSION / TRANSAXLE  SHIFT LEVER POSITION SENSOR  INSTALLATION  


PROCEDURE

Hide 89451A 1.INSTALL SHIFT LEVER POSITION SENSOR

a.

Move the shift lever to N.


b.
C378553

Clean and degrease the 2 bolt holes of the hybrid vehicle transaxle assembly.


c.
A192239C42
1.698,1.5 1.698,1.74 false 1.646,1.75 1.823,1.906 0.177,0.156 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the ends of 2 new bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

In order to ensure proper sealing of the 2 bolts, apply adhesive to the 2 bolts and install them within 10 minutes of applying adhesive.



d.

Temporarily install the shift lever position sensor to the hybrid vehicle transaxle assembly with the 2 bolts.

NOTICE:
·

Do not reuse the shift lever position sensor if it has been dropped or subjected to a severe impact.

·

Do not allow moisture to adhere to the connector terminal.




e.

Install the lock plate to the shift lever position sensor with the lock nut.

Torque:
6.9 N*m (70 kgf*cm, 61 in.*lbf)


f.

Temporarily install the control shaft lever to the shift lever position sensor.


g.
C377951N01
2.833,1.385 2.99,1.583 0.156,0.198 10 false N 2.583,2 2.75,2.177 0.167,0.177 10 false P

Turn the control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.


h.

Remove the control shaft lever from the shift lever position sensor.


i.
C377952C01
2.26,1.042 2.99,1.042 true 2.24,0.792 2.979,0.792 true 3.031,0.677 3.302,0.906 0.271,0.229 10 false *a 3.031,0.938 3.26,1.156 0.229,0.219 10 false *b 0.677,0.615 0.979,0.823 0.302,0.208 10 false *c
*a Neutral Basic Line
*b Indicator
*c Range of Play


Align the indicator with the neutral basic line.

NOTICE:

The indicator of the lock plate has a certain amount of play. Align the center point of the range of play with the neutral basic line.



j.

Tighten the 2 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


k.

Using a screwdriver with its tip wrapped with protective tape, secure the lock nut with the lock plate.


l.

Install the control shaft lever and washer to the shift lever position sensor with the nut.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


m.

Connect the shift lever position sensor connector.


Hide 33820B 2.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Engage the 2 claws to install a new clip to the transmission control cable assembly.


b.
C377953C01
1.25,1.385 0.969,0.573 0.969,0.573 2.167,1.365 true 1.146,1.635 2.948,2.521 2.948,2.521 2.313,1.646 true 2.646,1.063 2.75,0.698 2.75,0.698 2.896,0.698 false 1.26,2.979 1.406,2.979 1.406,2.979 1.583,2.417 true 1.094,2.917 1.385,3.156 0.292,0.24 10 false *1 2.958,0.625 3.26,0.802 0.302,0.177 10 false *2 0.792,0.479 1.104,0.667 0.313,0.188 10 false *a 3,2.469 3.313,2.625 0.313,0.156 10 false *b
*1 Transmission Control Cable Assembly
*2 No. 1 Transmission Control Cable Bracket
*a Claw (A)
*b Claw (B)


Using a screwdriver, engage the 4 claws and install the transmission control cable assembly to the No. 1 transmission control cable bracket.

NOTICE:
·

Make sure that the claws (A) of the clip are securely engaged in the grooves of the bracket.

·

Make sure that the transmission control cable assembly is securely installed inside of the claws (B) of the clip.




c.

Connect the transmission control cable assembly to the control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 3.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide 12601B 4.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 17750A 5.INSTALL INLET AIR CLEANER ASSEMBLY

Hide 53295E 6.INSTALL COOL AIR INTAKE DUCT SEAL

Hide 7.INSPECT SHIFT LEVER POSITION SENSOR POSITION

Hide 11.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY (w/ Cover)

Hide 51441 12.INSTALL NO. 1 ENGINE UNDER COVER

Hide 53852K 13.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851M 14.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH