Home › Engine / Hybrid System › A25A-FXS (ENGINE MECHANICAL) › CAMSHAFT
RM33C0E _51 Engine / Hybrid System _065420 A25A-FXS ENGINE MECHANICAL _0324463 CAMSHAFT A

A25A-FXS ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1.INSTALL CAMSHAFT

HINT:

Perform inspection after repair after replacing the camshaft, No. 2 camshaft, camshaft timing gear assembly and camshaft timing exhaust gear assembly.

w/ Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION

w/o Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION


a.
A445997C01
2,1.854 2.219,1.854 2.219,1.854 2.344,1.385 true 2.427,1.458 2.688,1.75 2.688,1.75 2.844,1.75 true 2.865,1.667 3.073,1.865 0.208,0.198 10 true *a 1.813,1.781 2.01,1.948 0.198,0.167 10 true *b
*a "0" Timing Mark
*b Timing Mark


Turn the crankshaft clockwise to align the timing mark (cutout) on the crankshaft pulley assembly with the "0" timing mark on the No. 2 timing gear cover assembly.


b.
A400400C02
2.531,0.906 2.896,0.906 false 1.885,0.406 2.052,0.24 2.052,0.24 2.208,0.24 false 0.677,0.76 1.042,0.76 false 2.26,0.146 2.573,0.344 0.313,0.198 10 false *1 2.958,0.823 3.271,1.021 0.313,0.198 10 false *2 0.479,0.667 0.792,0.865 0.313,0.198 10 false *3
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem Cap


Check that the No. 1 valve rocker arm sub-assembly is correctly installed as shown in the illustration.


c.

Clean the camshaft housing sub-assembly and the cams and journals of the camshaft and No. 2 camshaft, and then apply engine oil to them.


d.

Apply a light coat of engine oil to the journals of the camshaft and install the camshaft to the camshaft housing sub-assembly.


e.

Apply a light coat of engine oil to the journals of the No. 2 camshaft and install the No. 2 camshaft to the camshaft housing sub-assembly.


f.
A445994C02
1.125,0.885 1.302,0.885 true 0.26,0.802 0.448,0.802 true 1.375,1.344 1.375,1.177 1.375,1.177 1.604,1.052 true 2.552,0.802 2.729,0.802 true 1.948,1.344 1.948,1.177 1.948,1.177 2.177,1.052 true 1.823,1.979 1.958,2.156 0.135,0.177 10 false 1 1.813,0.094 1.948,0.271 0.135,0.177 10 false 2 2.417,1.979 2.552,2.156 0.135,0.177 10 false 3 2.396,0.094 2.531,0.271 0.135,0.177 10 false 4 1.25,1.99 1.385,2.167 0.135,0.177 10 true 5 1.25,0.094 1.385,0.271 0.135,0.177 10 false 6 2.417,1.385 2.552,1.563 0.135,0.177 10 true 7 2.875,0.083 3.01,0.26 0.135,0.177 10 false 8 2.958,1.99 3.094,2.167 0.135,0.177 10 false 9 3.177,1.427 3.375,1.594 0.198,0.167 10 true 10 3.208,0.073 3.406,0.24 0.198,0.167 10 false 11 0.625,2 0.823,2.167 0.198,0.167 10 true 12 0.771,0.031 0.969,0.198 0.198,0.167 10 false 13 0.781,0.979 0.979,1.146 0.198,0.167 10 true 14 0.052,0.729 0.26,0.917 0.208,0.188 10 true *1 1.323,0.802 1.521,0.969 0.198,0.167 10 true *2 1.281,1.365 1.479,1.552 0.198,0.188 10 true *3 2.354,0.74 2.542,0.917 0.188,0.177 10 true *4 1.875,1.354 2.073,1.542 0.198,0.188 10 true *3
*1 No. 1 Camshaft Bearing Cap
*2 No. 2 Camshaft Bearing Cap
*3 No. 3 Camshaft Bearing Cap
*4 No. 4 Camshaft Bearing Cap


Set the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, 2 No. 3 camshaft bearing caps and No. 4 camshaft bearing cap as shown in the illustration.


g.

Uniformly tighten the 14 bolts in the order shown in the illustration.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


h.
A445993N02
1.906,0.406 2.031,0.583 0.125,0.177 10 true 2 1.781,1.552 1.906,1.729 0.125,0.177 10 true 1 2.375,1.552 2.5,1.729 0.125,0.177 10 true 3 2.5,0.417 2.625,0.594 0.125,0.177 10 true 4 1.177,1.563 1.302,1.74 0.125,0.177 10 true 5 1.323,0.406 1.448,0.583 0.125,0.177 10 true 6 2.979,1.552 3.104,1.729 0.125,0.177 10 true 7 0.646,1.531 0.771,1.708 0.125,0.177 10 true 8

Uniformly tighten the 8 bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


i.
A445998

Set the camshaft timing gear assembly and camshaft timing exhaust gear assembly to the chain sub-assembly as shown in the illustration.


j.
A445999C01
2.135,1.115 2.135,0.781 true 2.177,0.552 2.51,0.302 2.51,0.302 2.656,0.302 true 2.063,1.115 2.271,1.313 0.208,0.198 10 true *a 2.677,0.219 2.896,0.427 0.219,0.208 10 true *b
*a Paint Mark
*b Timing Mark


Align the timing mark on the camshaft timing gear assembly with the paint mark on the chain sub-assembly.


k.
A446000C01
1.26,0.969 1.26,0.781 1.26,0.781 1.667,0.417 true 1.729,0.615 2.198,0.823 2.198,0.823 2.198,1.01 true 1.167,1 1.354,1.208 0.188,0.208 10 true *a 2.115,1.021 2.323,1.219 0.208,0.198 10 true *b
*a Paint Mark
*b Timing Mark


Align the timing mark on the camshaft timing exhaust gear assembly with the paint mark on the chain sub-assembly.


l.
A446001C01
1.448,1.417 1.448,1.135 1.448,1.135 1.688,0.906 true 1.365,1.438 1.552,1.625 0.188,0.188 10 true *a
*a Knock Pin


Using the hexagonal portion of the camshaft, install the camshaft timing gear assembly to the camshaft.


m.

Check that the knock pin matches the pin hole from the No. 2 timing gear cover sub-assembly side.


n.

Using a 10 mm bi-hexagon socket wrench, temporarily install the camshaft timing gear assembly with the bolt.

HINT:

Temporarily install the bolt enough that the camshaft timing gear assembly does not detach from the knock pin of the camshaft.



o.

Type A:

i.
A445988

Using the hexagonal portion of the No. 2 camshaft, install the camshaft timing exhaust gear assembly to the No. 2 camshaft.


ii.

Temporarily install the 2 bolts.

HINT:

The 2 bolts can only be installed as shown in the illustration if the knock pin on the No. 2 camshaft and the pin hole on the camshaft timing exhaust gear assembly match. If the 2 bolts cannot be installed, the knock pin and pin hole do not match.




p.

Type B:

i.
A473301

Using the hexagonal portion of the No. 2 camshaft, install the camshaft timing exhaust gear assembly to the No. 2 camshaft.


ii.

Temporarily install the 2 bolts.

HINT:

The 2 bolts can only be installed as shown in the illustration if the knock pin on the No. 2 camshaft and the pin hole on the camshaft timing exhaust gear assembly match. If the 2 bolts cannot be installed, the knock pin and pin hole do not match.




q.
A446002C01
1.844,0.865 2.573,1.094 2.573,1.094 2.802,1.094 true 2.844,1.021 3.052,1.208 0.208,0.188 10 false *1
*1 No. 1 Chain Vibration Damper


Check the status of the camshaft timing gear assembly and camshaft timing exhaust gear assembly temporarily installed to each camshaft.

i.

Camshaft timing gear assembly side:

Check that the chain sub-assembly does not overlap the No. 1 chain vibration damper as shown in the illustration.

NOTICE:

If the chain sub-assembly overlaps the No. 1 chain vibration damper, install it again.



ii.
A446003C01
1.385,0.573 1.604,0.573 1.604,0.573 2.25,0.729 true 1.177,0.5 1.385,0.677 0.208,0.177 10 false *1
*1 Chain Tensioner Slipper


Camshaft timing exhaust gear assembly side:

Check that the chain sub-assembly does not overlap the chain tensioner slipper as shown in the illustration.

NOTICE:

If the chain sub-assembly overlaps the chain tensioner slipper, install it again.




r.
A446004C01
2.333,0.198 2.542,0.396 0.208,0.198 10 true *a
*a Hold


Using the hexagonal portion of the camshaft, hold the camshaft.

NOTICE:
·

Do not damage the camshaft housing sub-assembly, cylinder head sub-assembly and spark plug tube.

·

Do not disassemble the camshaft timing gear assembly.




s.

Using a 10 mm bi-hexagon socket wrench, tighten the bolt on the camshaft timing gear assembly.

Torque:
86 N*m (877 kgf*cm, 63 ft.*lbf)


t.

Type A:

i.
A445988C01
2.938,0.042 3.167,0.229 0.229,0.188 10 false *a
*a Hold


Using the hexagonal portion of the No. 2 camshaft, hold the No. 2 camshaft.

NOTICE:

Do not damage the camshaft housing sub-assembly, cylinder head sub-assembly and spark plug tube.



ii.

Using a 5 mm hexagon wrench, tighten the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)



u.

Type B:

i.
A473301C01
2.938,0.042 3.167,0.229 0.229,0.188 10 false *a
*a Hold


Using the hexagonal portion of the No. 2 camshaft, hold the No. 2 camshaft.

NOTICE:

Do not damage the camshaft housing sub-assembly, cylinder head sub-assembly and spark plug tube.



ii.

Using a 5 mm hexagon wrench, tighten the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)



v.
A446005C01
0.813,0.552 1,0.552 1,0.552 1.146,0.813 true 0.802,1.583 0.802,1.323 0.802,1.323 1.094,1.042 true 1.406,1.552 1.25,1.552 1.25,1.552 1.146,1.188 true 2.677,1.042 2.833,1.646 2.833,1.646 2.979,1.646 true 2.708,0.896 2.927,0.729 2.927,0.729 3.083,0.729 true 2.698,0.792 2.938,0.458 2.938,0.458 3.094,0.458 true 3.01,1.542 3.208,1.719 0.198,0.177 10 true *a 1.448,1.469 1.656,1.656 0.208,0.188 10 true *b 3.104,0.635 3.313,0.823 0.208,0.188 10 true *b 3.125,0.385 3.333,0.573 0.208,0.188 10 true *b 0.594,0.469 0.802,0.656 0.208,0.188 10 true *b 0.719,1.594 0.917,1.771 0.198,0.177 10 true *a
*a Paint Mark
*b Timing Mark


Check that the paint marks and timing marks are positioned as shown in the illustration.


w.

Using the hexagonal portion of the camshaft, check that the chain sub-assembly slackens when the camshaft is moved in the direction shown in the illustration.

A446006C01
5.844,0.031 6.063,0.208 0.219,0.177 10 false *a
*a Hold - -
V100135

Turn - -


NOTICE:

If the chain sub-assembly remains tight and does not slacken, the chain tensioner slipper and No. 1 chain vibration damper may overlap the chain sub-assembly, so install them again.



x.

Remove the pin from the No. 1 chain tensioner assembly.


Hide 3.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

Hide 23477 4.INSTALL FUEL PUMP LIFTER GUIDE

Hide 11193 5.INSTALL SPARK PLUG TUBE GASKET

Hide 11201 6.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 13090E 7.INSTALL CAM TIMING CONTROL MOTOR O-RING

Hide 13090D 8.INSTALL CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

Hide 135A0A 9.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY)

Hide 15370 10.INSTALL CAM TIMING OIL CONTROL SOLENOID ASSEMBLY

Hide 82121 12.CONNECT ENGINE WIRE

a.
A445983

Engage the 3 clamps to connect the engine wire.


b.

Engage the 6 connectors.


Hide 88710E 13.CONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY

a.

Engage the 2 clamps to connect the air conditioning tube and accessory assembly.


Hide 23100X 14.INSTALL FUEL(ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)