Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM33C0E _54 Brake _065442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0328411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1401  Malfunction in Front Speed Sensor RH Circuit  C1402  Malfunction in Front Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1413 and C1414.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1413

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1401 Malfunction in Front Speed Sensor RH Circuit 501
502
507
·

INF Code: 501

-

At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.


·

INF Code: 502

-

At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more. (except when both rear speed sensors are 0 km/h (0 mph)).


·

INF Code: 507

-

At a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.



·

Front speed sensor RH

·

Speed sensor installed improperly

·

Front speed sensor rotor RH (front axle hub sub-assembly RH)

·

Wire harness or connector


ABS DTC
C1402 Malfunction in Front Speed Sensor LH Circuit 511
512
517
·

INF Code: 511

-

At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.


·

INF Code: 512

-

At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more. (except when both rear speed sensors are 0 km/h (0 mph)).


·

INF Code: 517

-

At a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.



·

Front speed sensor LH

·

Speed sensor installed improperly

·

Front speed sensor rotor LH (front axle hub sub-assembly LH)

·

Wire harness or connector


ABS DTC

PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1401 is output. A
DTC C1402 is output. B



A

2.CHECK FRONT SPEED SENSOR RH INSTALLATION

B

7.CHECK FRONT SPEED SENSOR LH INSTALLATION
2.CHECK FRONT SPEED SENSOR RH INSTALLATION
a.
C168336C29
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Front Speed Sensor RH
*a OK
*b NG
*c 8.5 N*m (87 kgf*cm, 75 in.*lbf)
*d No Clearance


Check the front speed sensor RH installation.

OK:

There is no clearance between the sensor and the front steering knuckle.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Result:
Proceed to
OK
NG



OK

3.CHECK FRONT SPEED SENSOR RH (CHECK FOR FOREIGN MATTER)

NG

REINSTALL OR REPLACE FRONT SPEED SENSOR RH

3.CHECK FRONT SPEED SENSOR RH (CHECK FOR FOREIGN MATTER)
a.

b.

Check the front speed sensor tip RH.

OK:

The sensor tip is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the front speed sensor RH, clean the front speed sensor RH.

·

If the front speed sensor RH is damaged, replace the front speed sensor RH with a new one.

·

Check the front speed sensor RH signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (FRONT SPEED SENSOR RH)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR RH

4.READ VALUE USING GTS (FRONT SPEED SENSOR RH)
a.

Install the front speed sensor RH.


b.

Select the Data List on the GTS.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front speed sensor RH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
50003 105 1

c.

Check the front speed sensor RH output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - FRONT SPEED SENSOR RH)
5.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - FRONT SPEED SENSOR RH)
a.

Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Disconnect the A35 front speed sensor RH connector.


e.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-3 (FR+) - A35-1 (FR+) Always Below 1 Ω
A40-3 (FR+) or A35-1 (FR+) - Body ground Always 10 kΩ or higher
A40-4 (FR-) - A35-2 (FR-) Always Below 1 Ω
A40-4 (FR-) or A35-2 (FR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK FRONT SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK FRONT SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)
a.

Remove the front speed sensor RH and the component with the front speed sensor rotor RH.

for Front Speed Sensor RH: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL

for Front Speed Sensor Rotor RH: Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL


b.

Check the front speed sensor rotor RH.

OK:

The front speed sensor rotor RH is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the front speed sensor rotor RH, clean the front speed sensor rotor RH.

·

If the front speed sensor rotor RH is damaged, replace the front speed sensor rotor RH with a new one.

·

Check the front speed sensor RH signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



HINT:
·

The front speed sensor rotor RH is incorporated into the front axle hub sub-assembly RH.

·

If the front speed sensor rotor RH needs to be replaced, replace it together with the front axle hub sub-assembly RH.




Result:
Result Proceed to
OK A
NG (The front speed sensor rotor RH is damaged.) B
NG (There is foreign matter on the front speed sensor rotor RH.) C



A

B

REPLACE FRONT AXLE HUB SUB-ASSEMBLY RH

C

CLEAN FRONT SPEED SENSOR ROTOR RH

7.CHECK FRONT SPEED SENSOR LH INSTALLATION
a.
C168336C29
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Front Speed Sensor LH
*a OK
*b NG
*c 8.5 N*m (87 kgf*cm, 75 in.*lbf)
*d No Clearance


Check the front speed sensor LH installation.

OK:

There is no clearance between the sensor and the front steering knuckle.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Result:
Proceed to
OK
NG



OK

8.CHECK FRONT SPEED SENSOR LH (CHECK FOR FOREIGN MATTER)

NG

REINSTALL OR REPLACE FRONT SPEED SENSOR LH

8.CHECK FRONT SPEED SENSOR LH (CHECK FOR FOREIGN MATTER)
a.

b.

Check the front speed sensor tip LH.

OK:

The sensor tip is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the front speed sensor LH, clean the front speed sensor LH.

·

If the front speed sensor LH is damaged, replace the front speed sensor LH with a new one.

·

Check the front speed sensor LH signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK
NG



OK

9.READ VALUE USING GTS (FRONT SPEED SENSOR LH)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR LH

9.READ VALUE USING GTS (FRONT SPEED SENSOR LH)
a.

Install the front speed sensor LH.


b.

Select the Data List on the GTS.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FL Wheel Speed Front speed sensor LH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
FL Wheel Speed
50003 105 2

c.

Check the front speed sensor LH output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

NG

10.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - FRONT SPEED SENSOR LH)
10.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - FRONT SPEED SENSOR LH)
a.

Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Disconnect the A36 front speed sensor LH connector.


e.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-31 (FL+) - A36-1 (FL+) Always Below 1 Ω
A40-31 (FL+) or A36-1 (FL+) - Body ground Always 10 kΩ or higher
A40-32 (FL-) - A36-2 (FL-) Always Below 1 Ω
A40-32 (FL-) or A36-2 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK FRONT SPEED SENSOR ROTOR LH (CHECK FOR FOREIGN MATTER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK FRONT SPEED SENSOR ROTOR LH (CHECK FOR FOREIGN MATTER)
a.

Remove the front speed sensor LH and the component with the front speed sensor rotor LH.

for Front Speed Sensor LH: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL

for Front Speed Sensor Rotor LH: Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL


b.

Check the front speed sensor rotor LH.

OK:

The front speed sensor rotor LH is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the front speed sensor rotor LH, clean the front speed sensor rotor LH.

·

If the front speed sensor rotor LH is damaged, replace the front speed sensor rotor LH with a new one.

·

Check the front speed sensor LH signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



HINT:
·

The front speed sensor rotor LH is incorporated into the front axle hub sub-assembly LH.

·

If the front speed sensor rotor LH needs to be replaced, replace it together with the front axle hub sub-assembly LH.




Result:
Result Proceed to
OK A
NG (The front speed sensor rotor LH is damaged.) B
NG (There is foreign matter on the front speed sensor rotor LH.) C



A

B

REPLACE FRONT AXLE HUB SUB-ASSEMBLY LH

C

CLEAN FRONT SPEED SENSOR ROTOR LH