Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM33C0E _54 Brake _065442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0328411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1413  Front Speed Sensor RH Circuit Output  C1414  Front Speed Sensor LH Circuit Output  


DESCRIPTION

Each speed sensor detects the wheel speed and sends the signals to the skid control ECU (brake booster with master cylinder assembly). These signals are used for ABS control.

HINT:

The output voltage values shown below are for when the vehicle wire harnesses are connected to the skid control ECU (brake booster with master cylinder assembly) and the speed sensors.


C223506E15
1.281,1.063 1.281,0.708 1.281,0.708 1.073,0.708 false 0.156,0.604 1.344,0.917 1.188,0.313 10 Speed Sensor 4.938,1.917 5.781,2.104 0.844,0.188 10 High speed 4.01,1.917 4.792,2.104 0.781,0.188 10 Low speed 6.052,1.156 6.51,1.427 0.458,0.271 10 1.4 V 6.052,1.49 6.542,1.813 0.49,0.323 10 0.7 V 0.906,2.177 2.365,2.385 1.458,0.208 10 Speed Sensor Rotor

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1413 Front Speed Sensor RH Circuit Output 504
541
·

INF Code: 504

-

An open in the sensor signal of a malfunctioning wheel occurs 255 times or more.


·

INF Code: 541

-

Either of the following is detected:

(1)

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

(2)

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.




·

Front speed sensor RH

·

Speed sensor installed improperly

·

Wire harness or connector

·

Front speed sensor rotor RH (front axle hub sub-assembly RH)

·

Skid control ECU (brake booster with master cylinder assembly)


ABS DTC
C1414 Front Speed Sensor LH Circuit Output 514
542
·

INF Code: 514

-

An open in the sensor signal of a malfunctioning wheel occurs 255 times or more.


·

INF Code: 542

-

Either of the following is detected:

(1)

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

(2)

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.




·

Front speed sensor LH

·

Speed sensor installed improperly

·

Wire harness or connector

·

Front speed sensor rotor LH (front axle hub sub-assembly LH)

·

Skid control ECU (brake booster with master cylinder assembly)


ABS DTC

DTC Detection Conditions: C1413 INF Code: 541
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition At a vehicle speed of 20 km/h (12 mph) or more. ○ -
At a vehicle speed of 10 km/h (6 mph) or more. - ○
Malfunction Status Noise occurs in the sensor signals of a malfunctioning wheel. ○ -
Noise occurs once per rotor rotation. - ○
Detection Time Detected 75 times or more within 5 seconds 15 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1414 INF Code: 542
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition At a vehicle speed of 20 km/h (12 mph) or more. ○ -
At a vehicle speed of 10 km/h (6 mph) or more. - ○
Malfunction Status Noise occurs in the sensor signals of a malfunctioning wheel. ○ -
Noise occurs once per rotor rotation. - ○
Detection Time Detected 75 times or more within 5 seconds 15 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C343057E10
5.656,0.771 5.969,0.969 0.313,0.198 10 false 3 5.813,0.969 6.125,1.167 0.313,0.198 10 false FR+ 5.656,1.448 5.969,1.646 0.313,0.198 10 false 4 5.813,1.646 6.125,1.844 0.313,0.198 10 false FR- 5.583,3.156 5.896,3.354 0.313,0.198 10 false 31 5.813,3.365 6.125,3.563 0.313,0.198 10 false FL+ 5.583,3.833 5.896,4.031 0.313,0.198 10 false 32 5.813,4.042 6.125,4.24 0.313,0.198 10 false FL- 5.083,4.938 5.396,5.135 0.313,0.198 10 false A40 5.063,5.135 7.125,5.531 2.063,0.396 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 3.708,2.177 4.021,2.375 0.313,0.198 10 false * 3.729,4.583 4.042,4.781 0.313,0.198 10 false * 1.25,1.448 1.563,1.646 0.313,0.198 10 false 1 2.188,1.448 2.5,1.646 0.313,0.198 10 false 2 1.427,1.552 1.74,1.75 0.313,0.198 10 false FR+ 1.854,1.552 2.167,1.75 0.313,0.198 10 false FR- 1.042,1.865 1.354,2.063 0.313,0.198 10 false A35 1.031,2.031 2.573,2.24 1.542,0.208 10 false Front Speed Sensor RH 1.26,3.833 1.573,4.031 0.313,0.198 10 false 1 1.417,3.938 1.729,4.135 0.313,0.198 10 false FL+ 1.865,3.938 2.177,4.135 0.313,0.198 10 false FL- 2.177,3.833 2.49,4.031 0.313,0.198 10 false 2 1.094,4.26 1.406,4.458 0.313,0.198 10 false A36 1.083,4.417 2.615,4.615 1.531,0.198 10 false Front Speed Sensor LH 1.781,5.104 2.792,5.292 1.01,0.188 10 false *: Shielded

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1413 is output. A
DTC C1414 is output. B



A

2.READ VALUE USING GTS (MOMENTARY INTERRUPTION)

B

9.READ VALUE USING GTS (MOMENTARY INTERRUPTION)
2.READ VALUE USING GTS (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Speed Sensor Voltage Open Front speed sensor RH voltage open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Speed Sensor Voltage Open
50003 105 294

b.

Check for any momentary interruptions in the wire harness and connectors.

OK:

There are no momentary interruptions.


NOTICE:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (FRONT SPEED SENSOR RH)

NG

5.CHECK FRONT SPEED SENSOR RH INSTALLATION
3.READ VALUE USING GTS (FRONT SPEED SENSOR RH)
a.

Select the Data List on the GTS.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front speed sensor RH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
50003 105 1

b.

Check the front speed sensor RH output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

5.CHECK FRONT SPEED SENSOR RH INSTALLATION
4.RECONFIRM DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (READY).


d.

Perform a road test.


e.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1413 is not output. A
DTC C1413 is output. B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

5.CHECK FRONT SPEED SENSOR RH INSTALLATION
a.
C168336C29
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Front Speed Sensor RH
*a OK
*b NG
*c 8.5 N*m (87 kgf*cm, 75 in.*lbf)
*d No Clearance


Turn the power switch off.


b.

Check the front speed sensor RH installation.

OK:

There is no clearance between the sensor and the front steering knuckle.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Result:
Proceed to
OK
NG



OK

6.CHECK FRONT SPEED SENSOR RH AND FRONT SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)

NG

REINSTALL OR REPLACE FRONT SPEED SENSOR RH

6.CHECK FRONT SPEED SENSOR RH AND FRONT SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)
a.

Remove the front speed sensor RH and the component with the front speed sensor rotor RH.

for Front Speed Sensor RH: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL

for Front Speed Sensor Rotor RH: Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL


b.

Check the front speed sensor tip RH and front speed sensor rotor RH.

OK:

The sensor tip and rotor are free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the front speed sensor RH, clean the front speed sensor RH and then check the front speed sensor rotor RH.

·

If the front speed sensor RH is damaged, replace the front speed sensor RH with a new one.

·

Check the front speed sensor RH signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - FRONT SPEED SENSOR RH)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR RH AND FRONT SPEED SENSOR ROTOR RH

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - FRONT SPEED SENSOR RH)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Disconnect the A35 front speed sensor RH connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-3 (FR+) - A35-1 (FR+) Always Below 1 Ω
A40-3 (FR+) or A35-1 (FR+) - Body ground Always 10 kΩ or higher
A40-4 (FR-) - A35-2 (FR-) Always Below 1 Ω
A40-4 (FR-) or A35-2 (FR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)
a.
C380194C08
1.5,0.688 1.896,0.979 0.396,0.292 2.24,2.688 1.865,1.625 true 0.354,0.323 0.667,0.521 0.313,0.198 10 false *a 1.583,0.75 1.896,0.948 0.313,0.198 10 false A35 2.156,2.719 2.563,2.958 0.406,0.24 10 false FR+
*a Front view of wire harness connector
(to Front Speed Sensor RH)


Reconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A35-1 (FR+) - Body ground Power switch on (IG) 8 to 14 V


NOTICE:

Check the front speed sensor RH signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

9.READ VALUE USING GTS (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FL Speed Sensor Voltage Open Front speed sensor LH voltage open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
FL Speed Sensor Voltage Open
50003 105 295

b.

Check for any momentary interruptions in the wire harness and connectors.

OK:

There are no momentary interruptions.


NOTICE:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

10.READ VALUE USING GTS (FRONT SPEED SENSOR LH)

NG

12.CHECK FRONT SPEED SENSOR LH INSTALLATION
10.READ VALUE USING GTS (FRONT SPEED SENSOR LH)
a.

Select the Data List on the GTS.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FL Wheel Speed Front speed sensor LH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
FL Wheel Speed
50003 105 2

b.

Check the front speed sensor LH output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

11.RECONFIRM DTC

NG

12.CHECK FRONT SPEED SENSOR LH INSTALLATION
11.RECONFIRM DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (READY).


d.

Perform a road test.


e.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1414 is not output. A
DTC C1414 is output. B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

12.CHECK FRONT SPEED SENSOR LH INSTALLATION
a.
C168336C29
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Front Speed Sensor LH
*a OK
*b NG
*c 8.5 N*m (87 kgf*cm, 75 in.*lbf)
*d No Clearance


Turn the power switch off.


b.

Check the front speed sensor LH installation.

OK:

There is no clearance between the sensor and the front steering knuckle.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Result:
Proceed to
OK
NG



OK

13.CHECK FRONT SPEED SENSOR LH AND FRONT SPEED SENSOR ROTOR LH (CHECK FOR FOREIGN MATTER)

NG

REINSTALL OR REPLACE FRONT SPEED SENSOR LH

13.CHECK FRONT SPEED SENSOR LH AND FRONT SPEED SENSOR ROTOR LH (CHECK FOR FOREIGN MATTER)
a.

Remove the front speed sensor LH and the component with the front speed sensor rotor LH.

for Front Speed Sensor LH: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL

for Front Speed Sensor Rotor LH: Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL


b.

Check the front speed sensor tip LH and front speed sensor rotor LH.

OK:

The sensor tip and rotor are free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the front speed sensor LH, clean the front speed sensor LH and then check the front speed sensor rotor LH.

·

If the front speed sensor LH is damaged, replace the front speed sensor LH with a new one.

·

Check the front speed sensor LH signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - FRONT SPEED SENSOR LH)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR LH AND FRONT SPEED SENSOR ROTOR LH

14.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - FRONT SPEED SENSOR LH)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Disconnect the A36 front speed sensor LH connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-31 (FL+) - A36-1 (FL+) Always Below 1 Ω
A40-31 (FL+) or A36-1 (FL+) - Body ground Always 10 kΩ or higher
A40-32 (FL-) - A36-2 (FL-) Always Below 1 Ω
A40-32 (FL-) or A36-2 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)
a.
C380194C09
1.5,0.688 1.896,0.979 0.396,0.292 2.24,2.688 1.865,1.625 true 0.354,0.323 0.667,0.521 0.313,0.198 10 false *a 1.583,0.75 1.896,0.948 0.313,0.198 10 false A36 2.156,2.719 2.563,2.958 0.406,0.24 10 false FL+
*a Front view of wire harness connector
(to Front Speed Sensor LH)


Reconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A36-1 (FL+) - Body ground Power switch on (IG) 8 to 14 V


NOTICE:

Check the front speed sensor LH signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY