Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM33C0E _54 Brake _065442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0328411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1405  Open or Short in Front Speed Sensor RH Circuit  C1406  Open or Short in Front Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1413 and C1414.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1413

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1405 Open or Short in Front Speed Sensor RH Circuit 503
506
508
·

INF Code: 503

-

An open in the speed sensor signal circuit continues for 0.5 seconds or more.


·

INF Code: 506

-

The speed sensor power source voltage is low for 0.5 seconds or more.


·

INF Code: 508

-

The speed sensor power source voltage is low for 0.2 seconds, and does not return to normal for 60 seconds or more.



·

Front speed sensor RH

·

Wire harness or connector

·

Skid control ECU (brake booster with master cylinder assembly)


ABS DTC
C1406 Open or Short in Front Speed Sensor LH Circuit 513
516
518
·

INF Code: 513

-

An open in the speed sensor signal circuit continues for 0.5 seconds or more.


·

INF Code: 516

-

The speed sensor power source voltage is low for 0.5 seconds or more.


·

INF Code: 518

-

The speed sensor power source voltage is low for 0.2 seconds, and does not return to normal for 60 seconds or more.



·

Front speed sensor LH

·

Wire harness or connector

·

Skid control ECU (brake booster with master cylinder assembly)


ABS DTC

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1405 is output. A
DTC C1406 is output. B



A

2.READ VALUE USING GTS (MOMENTARY INTERRUPTION)

B

7.READ VALUE USING GTS (MOMENTARY INTERRUPTION)
2.READ VALUE USING GTS (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Speed Open Front speed sensor RH open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Speed Open
50003 105 200

b.

Check for any momentary interruptions in the wire harness and connectors.

OK:

There are no momentary interruptions.


NOTICE:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (FRONT SPEED SENSOR RH)

NG

5.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - FRONT SPEED SENSOR RH)
3.READ VALUE USING GTS (FRONT SPEED SENSOR RH)
a.

Select the Data List on the GTS.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front speed sensor RH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
50003 105 1

b.

Check the front speed sensor RH output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

5.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - FRONT SPEED SENSOR RH)
4.RECONFIRM DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (READY).


d.

Perform a road test.


e.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1405 is not output. A
DTC C1405 is output. B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - FRONT SPEED SENSOR RH)
a.

Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Disconnect the A35 front speed sensor RH connector.


e.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-3 (FR+) - A35-1 (FR+) Always Below 1 Ω
A40-3 (FR+) or A35-1 (FR+) - Body ground Always 10 kΩ or higher
A40-4 (FR-) - A35-2 (FR-) Always Below 1 Ω
A40-4 (FR-) or A35-2 (FR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)
a.
C380194C08
1.5,0.688 1.896,0.979 0.396,0.292 2.24,2.688 1.865,1.625 true 0.354,0.323 0.667,0.521 0.313,0.198 10 false *a 1.583,0.75 1.896,0.948 0.313,0.198 10 false A35 2.156,2.719 2.563,2.958 0.406,0.24 10 false FR+
*a Front view of wire harness connector
(to Front Speed Sensor RH)


Reconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A35-1 (FR+) - Body ground Power switch on (IG) 8 to 14 V


NOTICE:

Check the front speed sensor RH signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

7.READ VALUE USING GTS (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FL Speed Open Front speed sensor LH open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
FL Speed Open
50003 105 201

b.

Check for any momentary interruptions in the wire harness and connectors.

OK:

There are no momentary interruptions.


NOTICE:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

8.READ VALUE USING GTS (FRONT SPEED SENSOR LH)

NG

10.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - FRONT SPEED SENSOR LH)
8.READ VALUE USING GTS (FRONT SPEED SENSOR LH)
a.

Select the Data List on the GTS.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FL Wheel Speed Front speed sensor LH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
FL Wheel Speed
50003 105 2

b.

Check the front speed sensor LH output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

9.RECONFIRM DTC

NG

10.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - FRONT SPEED SENSOR LH)
9.RECONFIRM DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (READY).


d.

Perform a road test.


e.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1406 is not output. A
DTC C1406 is output. B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - FRONT SPEED SENSOR LH)
a.

Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Disconnect the A36 front speed sensor LH connector.


e.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-31 (FL+) - A36-1 (FL+) Always Below 1 Ω
A40-31 (FL+) or A36-1 (FL+) - Body ground Always 10 kΩ or higher
A40-32 (FL-) - A36-2 (FL-) Always Below 1 Ω
A40-32 (FL-) or A36-2 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)
a.
C380194C09
1.5,0.688 1.896,0.979 0.396,0.292 2.24,2.688 1.865,1.625 true 0.354,0.323 0.667,0.521 0.313,0.198 10 false *a 1.583,0.75 1.896,0.948 0.313,0.198 10 false A36 2.156,2.719 2.563,2.958 0.406,0.24 10 false FL+
*a Front view of wire harness connector
(to Front Speed Sensor LH)


Reconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A36-1 (FL+) - Body ground Power switch on (IG) 8 to 14 V


NOTICE:

Check the front speed sensor LH signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY