Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM33C0E _54 Brake _065442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0328411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1407  Open or Short in Rear Speed Sensor RH Circuit  C1408  Open or Short in Rear Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1415 and C1416.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1415

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1407 Open or Short in Rear Speed Sensor RH Circuit 523
526
528
·

INF Code: 523

-

An open in the speed sensor signal circuit continues for 0.5 seconds or more.


·

INF Code: 526

-

The speed sensor power source voltage is low for 0.5 seconds or more.


·

INF Code: 528

-

The speed sensor power source voltage is low for 0.2 seconds, and does not return to normal for 60 seconds or more.



·

Skid control sensor wire RH (NO. 1 parking brake wire assembly)

·

Rear speed sensor RH (rear axle hub and bearing assembly RH)

·

Wire harness or connector

·

Skid control ECU (brake booster with master cylinder assembly)


ABS DTC
C1408 Open or Short in Rear Speed Sensor LH Circuit 533
536
538
·

INF Code: 533

-

An open in the speed sensor signal circuit continues for 0.5 seconds or more.


·

INF Code: 536

-

The speed sensor power source voltage is low for 0.5 seconds or more.


·

INF Code: 538

-

The speed sensor power source voltage is low for 0.2 seconds, and does not return to normal for 60 seconds or more.



·

Skid control sensor wire LH (NO. 2 parking brake wire assembly)

·

Rear speed sensor LH (rear axle hub and bearing assembly LH)

·

Wire harness or connector

·

Skid control ECU (brake booster with master cylinder assembly)


ABS DTC

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION

·

Disassembly of the rear speed sensor from the rear axle hub and bearing assembly is prohibited.



PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1407 is output. A
DTC C1408 is output. B



A

2.READ VALUE USING GTS (MOMENTARY INTERRUPTION)

B

8.READ VALUE USING GTS (MOMENTARY INTERRUPTION)
2.READ VALUE USING GTS (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Speed Open Rear speed sensor RH open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Speed Open
50003 105 202

b.

Check for any momentary interruptions in the wire harness and connectors.


OK:

There are no momentary interruptions.


NOTICE:

Perform the above inspection before removing the sensor and connector.


Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (REAR SPEED SENSOR RH)

NG

5.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY
3.READ VALUE USING GTS (REAR SPEED SENSOR RH)
a.

Select the Data List on the GTS.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear speed sensor RH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
50003 105 3

b.

Check the rear speed sensor RH output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

5.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY
4.RECONFIRM DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (READY).


d.

Perform a road test.


e.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1407 is not output. A
DTC C1407 is output. B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

5.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY
a.
C251359C50
0.76,0.906 1.156,1.146 0.396,0.24 2.26,0.917 2.656,1.156 0.396,0.24 0.833,1.979 0.563,2.76 true 1.094,1.979 1.417,2.75 true 2.344,2.052 2.188,2.531 true 2.573,2.052 2.76,2.531 true 0.188,0.177 0.646,0.469 0.458,0.292 10 false *a 0.875,1.219 1.375,1.51 0.5,0.292 10 false *b 2.385,1.219 2.906,1.531 0.521,0.313 10 false *c 0.896,0.948 1.24,1.188 0.344,0.24 10 false u2 2.333,0.948 2.76,1.156 0.427,0.208 10 false uR1 0.438,2.781 1.021,3.021 0.583,0.24 10 false RA- 1.375,2.781 1.969,3.021 0.594,0.24 10 false RA+ 2.073,2.552 2.646,2.771 0.573,0.219 10 false RR+ 2.719,2.552 3.365,2.729 0.646,0.177 10 false RR-
*a Front view of skid control sensor wire RH (NO. 1 parking brake wire assembly)
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Remove the skid control sensor wire RH (NO. 1 parking brake wire assembly).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
u2-2 (RA+) - uR1-1 (RR+) Always Below 1 Ω
u2-2 (RA+) - uR1-2 (RR-) Always 10 kΩ or higher
u2-2 (RA+) or uR1-1 (RR+) - Body ground Always 10 kΩ or higher
u2-1 (RA-) - uR1-2 (RR-) Always Below 1 Ω
u2-1 (RA-) - uR1-1 (RR+) Always 10 kΩ or higher
u2-1 (RA-) or uR1-2 (RR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - NO. 1 PARKING BRAKE WIRE ASSEMBLY)

NG

REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - NO. 1 PARKING BRAKE WIRE ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-7 (RR+) - uR1-1 (RR+) Always Below 1 Ω
A40-7 (RR+) or uR1-1 (RR+) - Body ground Always 10 kΩ or higher
A40-8 (RR-) - uR1-2 (RR-) Always Below 1 Ω
A40-8 (RR-) or uR1-2 (RR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)
a.
C380198C11
1.49,0.844 1.906,1.146 0.417,0.302 2.219,2.677 1.875,2.01 true 0.385,0.354 0.698,0.552 0.313,0.198 10 false *a 1.583,0.917 1.896,1.115 0.313,0.198 10 false uR1 2.125,2.719 2.552,2.938 0.427,0.219 10 false RR+
*a Front view of wire harness connector
(to Skid Control Sensor Wire RH (NO. 1 Parking Brake Wire Assembly))


Reconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
uR1-1 (RR+) - Body ground Power switch on (IG) 8 to 14 V


NOTICE:

Check the rear speed sensor RH signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE


HINT:

The rear speed sensor RH and rear speed sensor rotor RH are incorporated into the rear axle hub and bearing assembly RH.

If the rear speed sensor RH and rear speed sensor rotor RH need to be replaced, replace the rear axle hub and bearing assembly RH.



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

8.READ VALUE USING GTS (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Speed Open Rear speed sensor LH open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
RL Speed Open
50003 105 203

b.

Check for any momentary interruptions in the wire harness and connectors.


OK:

There are no momentary interruptions.


NOTICE:

Perform the above inspection before removing the sensor and connector.


Result:
Proceed to
OK
NG



OK

9.READ VALUE USING GTS (REAR SPEED SENSOR LH)

NG

11.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
9.READ VALUE USING GTS (REAR SPEED SENSOR LH)
a.

Select the Data List on the GTS.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Wheel Speed Rear speed sensor LH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
RL Wheel Speed
50003 105 4

b.

Check the rear speed sensor LH output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

10.RECONFIRM DTC

NG

11.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
10.RECONFIRM DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (READY).


d.

Perform a road test.


e.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1408 is not output. A
DTC C1408 is output. B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

11.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
a.
C251359C51
0.76,0.906 1.156,1.146 0.396,0.24 2.26,0.917 2.656,1.156 0.396,0.24 0.833,1.979 0.563,2.76 true 1.094,1.979 1.417,2.75 true 2.344,2.052 2.188,2.531 true 2.573,2.052 2.76,2.531 true 0.188,0.177 0.646,0.469 0.458,0.292 10 false *a 0.875,1.219 1.375,1.51 0.5,0.292 10 false *b 2.385,1.219 2.906,1.531 0.521,0.313 10 false *c 0.906,0.948 1.219,1.146 0.313,0.198 10 false v2 2.354,0.958 2.813,1.156 0.458,0.198 10 false vR1 2.708,2.552 3.354,2.729 0.646,0.177 10 false RL- 2.073,2.563 2.646,2.781 0.573,0.219 10 false RL+ 1.365,2.781 1.958,3.021 0.594,0.24 10 false LA+ 0.438,2.792 1.031,3.031 0.594,0.24 10 false LA-
*a Front view of skid control sensor wire LH (NO. 2 parking brake wire assembly)
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Remove the skid control sensor wire LH (NO. 2 parking brake wire assembly).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
v2-2 (LA+) - vR1-1 (RL+) Always Below 1 Ω
v2-2 (LA+) - vR1-2 (RL-) Always 10 kΩ or higher
v2-2 (LA+) or vR1-1 (RL+) - Body ground Always 10 kΩ or higher
v2-1 (LA-) - vR1-2 (RL-) Always Below 1 Ω
v2-1 (LA-) - vR1-1 (RL+) Always 10 kΩ or higher
v2-1 (LA-) or vR1-2 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - NO. 2 PARKING BRAKE WIRE ASSEMBLY)

NG

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

12.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - NO. 2 PARKING BRAKE WIRE ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-34 (RL+) - vR1-1 (RL+) Always Below 1 Ω
A40-34 (RL+) or vR1-1 (RL+) - Body ground Always 10 kΩ or higher
A40-35 (RL-) - vR1-2 (RL-) Always Below 1 Ω
A40-35 (RL-) or vR1-2 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)
a.
C380198C12
1.49,0.844 1.906,1.146 0.417,0.302 2.219,2.677 1.875,2.01 true 0.385,0.354 0.698,0.552 0.313,0.198 10 false *a 1.583,0.906 1.896,1.104 0.313,0.198 10 false vR1 2.125,2.719 2.552,2.938 0.427,0.219 10 false RL+
*a Front view of wire harness connector
(to Skid Control Sensor Wire LH (NO. 2 Parking Brake Wire Assembly))


Reconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
vR1-1 (RL+) - Body ground Power switch on (IG) 8 to 14 V


NOTICE:

Check the rear speed sensor LH signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE


HINT:

The rear speed sensor LH and rear speed sensor rotor LH are incorporated into the rear axle hub and bearing assembly LH.

If the rear speed sensor LH and rear speed sensor rotor LH need to be replaced, replace the rear axle hub and bearing assembly LH.



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY