The ABS motor relay is built into the brake booster with master cylinder assembly.
During ABS, TRC, VSC, brake hold, secondary collision brake or brake assist operation, the skid control ECU (brake booster with master cylinder assembly) turns on the ABS motor relay to run the pump motor in the brake actuator assembly.
When any DTC related to the ABS motor is stored, the IC built into the skid control ECU (brake booster with master cylinder assembly) operates in fail-safe mode.
When the supplied voltage to the BM terminal of the ABS motor relay is excessively low due to an auxiliary battery or charging circuit malfunction, DTC C146C and/or C146D is stored.
| DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|---|
| C146C | Open Circuit in ABS Motor Relay Circuit | 612 | When operation of the ABS motor is requested, the ABS motor voltage is less than 7.6 V for 0.2 seconds or more. | ·
Wire harness or connector ·
Skid control ECU (brake booster with master cylinder assembly) ·
Brake actuator assembly |
ABS DTC |
| C146D | Short Circuit in ABS Motor Relay Circuit | 613 | A short in the ABS motor relay drive circuit is detected for 4 seconds or more. | ·
Wire harness or connector ·
Skid control ECU (brake booster with master cylinder assembly) ·
Brake actuator assembly |
ABS DTC |
Refer to DTC C1427.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1427
After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION
Inspect the fuses for circuits related to this system before performing the following procedure.
When DTCs C1241 and/or C1417 are output together with C146C and/or C146D, inspect and repair the trouble areas indicated by C1241 and/or C1417 first.
for C1241: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1241
for C1417: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1417
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A40-41 (BM) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A44 brake actuator assembly connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A40-40 (+BM) - A44-10 (+BM) | Always | Below 1 Ω |
| A40-40 (+BM) or A44-10 (+BM) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Brake Actuator Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A44-1 (MGND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.
Reconnect the A44 brake actuator assembly connector.
Clear the DTCs.
Turn the power switch off.
Turn the power switch on (READY).
Perform a road test.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| DTCs C146C and C146D are not output. | A |
| DTCs C146C and/or C146D are output. | B |
If a speed signal of 20 km/h (12 mph) or more is sent to the skid control ECU (brake booster with master cylinder assembly) with the power switch on (IG) and the stop light switch assembly off, the ECU performs self-diagnosis of the motor and solenoid circuits.
If the normal system code is output (no DTCs are output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake booster with master cylinder assembly).
If any DTCs are output while jiggling a connector or wire harness from the skid control ECU (brake booster with master cylinder assembly), inspect and repair the connector or wire harness.
The DTCs were probably output due to a bad connection of the connector terminal.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL