Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV BATTERY THERMISTOR › 2017.09–2019.02
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0328990 HV BATTERY THERMISTOR A

HYBRID / BATTERY CONTROL  HV BATTERY THERMISTOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during hybrid battery thermistor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ steering control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide G920NB 2.REMOVE UPPER HV BATTERY COVER SUB-ASSEMBLY

Hide G920R 4.REMOVE NO. 2 HYBRID BATTERY SHIELD SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A406100

Remove the 5 nuts.


b.
A406101C01
0.656,1.875 0.906,1.875 0.906,1.875 1.115,1.677 true 1.99,1.49 2.26,1.948 2.26,1.948 2.458,1.948 true 0.5,1.781 0.813,1.938 0.313,0.156 10 false *1 2.479,1.854 2.792,2.01 0.313,0.156 10 false *2
*1 Rear No. 1 HV Battery Shield
*2 No. 2 Hybrid Battery Shield Sub-assembly
V113147

Pull Back


Pull back the rear No. 1 HV battery shield and remove the No. 2 hybrid battery shield sub-assembly from the HV battery.

HINT:

Pull back the rear No. 1 HV battery shield until it is separated from the stud bolt of the No. 2 hybrid battery shield sub-assembly.



Hide G92E1A 5.REMOVE NO. 1 HV BATTERY INTAKE DUCT LH

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A406102

Remove the clip to disconnect the No. 1 HV battery intake duct LH from the HV battery.


b.

Disengage the claw of hybrid battery thermistor (sensor portion) and remove the No. 1 HV battery intake duct LH.


Hide G9282 6.REMOVE HYBRID BATTERY THERMISTOR

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A406103

Disengage the clamp.


b.
A406104

Disengage the 2 claws and remove the No. 1 hybrid battery packing from the HV battery.


c.
A406105

Disengage the clamp.


d.

Disconnect the battery voltage sensor connector.


e.
A406106

Disengage the 4 clamps.


f.
A406117

Disengage the 3 claws of the hybrid battery thermistor (sensor portions) and remove the hybrid battery thermistor from the HV battery.