Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV BATTERY (for NICKEL METAL HYDRIDE BATTERY) › 2017.09–2019.02
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0328989 HV BATTERY A

HYBRID / BATTERY CONTROL  HV BATTERY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the HV battery removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ steering control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of HV battery Battery status info update HV battery status information cannot be updated (Click here)
Replacement of hybrid battery terminal block Perform high voltage fuse accumulated load history reset DTCs are stored (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When the cable is disconnected from the negative (-) auxiliary battery terminal, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

If the HV battery has been struck or dropped, replace it.

·

When connecting a connector to the HV battery, confirm that the connector is securely connected through the following:

- Push the connector until a click sound is heard.

- Visually check and confirm that the connector is securely connected by pulling on it.

·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·

When performing repairs around the HV battery, such as using a tap, do not allow metal shavings to enter the HV battery.

·

Do not touch any high voltage wire harnesses, connectors or parts with bare hands.

·
A406064

Hold the areas shown in the illustration and lift the HV battery.

·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts or nuts of the HV battery.

·
A406065C01
1.115,0.896 0.938,0.406 0.938,0.406 0.625,0.406 true 0.448,0.302 0.76,0.458 0.313,0.156 10 false *a
*a Opening


Do not put your hands into the openings of the HV battery.

·

When removing/installing/moving the HV battery, make sure not to tilt it more than 80°.

·

Do not climb on top of or stand on the HV battery.

·

Do not allow any foreign matter or water to enter the HV battery.

·

If any bolts, nuts or clips are dropped into the HV battery, make sure to remove them.



HINT:

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.


PROCEDURE

Hide 82111 2.DISCONNECT ENGINE ROOM MAIN WIRE

Hide 5.INSTALL CONNECTOR COVER ASSEMBLY

CAUTION:

Be sure to wear insulated gloves.


a.
A406068C03
2.104,1.427 2.323,1.615 0.219,0.188 10 true *a 1.896,0.417 2.115,0.583 0.219,0.167 10 true *b
*a Bolt (A)
*b Bolt (B)


Using a T25 "TORX" socket wrench, install the connector cover assembly to the inverter with converter assembly with the bolt (A).

Torque:
4.5 N*m (46 kgf*cm, 40 in.*lbf)

NOTICE:

Do not touch the waterproof seal of the connector cover assembly.



b.

Install the bolt (B).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 82111 6.CONNECT ENGINE ROOM MAIN WIRE

Hide G9230 7.REMOVE BATTERY COOLING BLOWER ASSEMBLY

Hide G92N4A 8.REMOVE NO. 1 HV BATTERY COVER PANEL RH

CAUTION:

Be sure to wear insulated gloves.


a.
A406073C01
1.271,1.24 1.573,1.24 false 1.302,0.219 1.604,0.219 false 1.167,1.094 1.333,0.906 1.333,0.906 1.51,0.906 true 0.781,0.896 0.958,0.896 0.958,0.896 1.073,0.74 false 1.625,0.125 1.938,0.281 0.313,0.156 10 false *1 1.594,1.146 1.906,1.302 0.313,0.156 10 false *2 0.625,0.792 0.938,0.948 0.313,0.156 10 false *a 0.5,0.521 0.813,0.677 0.313,0.156 10 false *b 1.542,0.802 1.854,0.958 0.313,0.156 10 false *c
*1 Service Plug Grip
*2 Battery Cover Lock Striker
*a Projection
*b Turn
*c Button


Using the service plug grip, remove the battery cover lock striker.

HINT:

Insert the projection of the service plug grip and turn the button of the battery cover lock striker counterclockwise to release the lock.



b.

Remove the 3 bolts, 3 nuts and No. 1 HV battery cover panel RH from the HV battery.


Hide 821H1 9.DISCONNECT HV FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
A406074C01
1.875,1.25 2.396,1.25 true 2.396,1.146 2.594,1.344 0.198,0.198 10 true *a
*a Shield Ground


Disconnect the 2 HV battery junction block assembly connectors.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



b.

Disconnect the shield ground from the HV battery.


c.
A406076

Disconnect the floor wire connector.


Hide 82161 10.DISCONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
A406075

Disengage the clamp.


b.

Disconnect the electric vehicle battery plug assembly connector.


c.

Disconnect the HV battery junction block assembly connector.


Hide 899A0 11.REMOVE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY

Hide 82161 12.DISCONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
A406077

Disengage the 2 clamps to disconnect the floor wire.


Hide G92F1 13.REMOVE NO. 1 HYBRID BATTERY EXHAUST DUCT

CAUTION:

Be sure to wear insulated gloves.


a.
A406078

Remove the clip.


b.

Disengage the claw to remove the No. 1 hybrid battery exhaust duct from the HV battery.


Hide 82161 14.DISCONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
A406079

Disengage the clamp.


b.

Disconnect the battery voltage sensor connector.


Hide G9510 15.REMOVE HV BATTERY

CAUTION:

Be sure to wear insulated gloves.


a.
A406080

Remove the 5 bolts and HV battery from the vehicle body.

NOTICE:
·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the HV battery.

·

To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.

·

Use cardboard or another similar material to protect the HV battery and vehicle body from damage.

·

Since the HV battery is very heavy, 2 people are needed to remove it. When removing the HV battery, be careful not to damage the parts around it.

·

When removing the HV battery from the vehicle, do not allow it to contact the vehicle.

·

When removing/installing/moving the HV battery, make sure not to tilt it more than 80°.

·

Insulate the disconnected terminals or connectors with insulating tape.

·

If the HV battery has been struck or dropped, replace it.




Hide G920TA 16.REMOVE NO. 4 HV BATTERY SHIELD SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves.


a.
A406082

Remove the 4 nuts and No. 4 HV battery shield sub-assembly from the HV battery.


Hide G920SA 17.REMOVE NO. 3 HV BATTERY SHIELD SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves.


a.
A406081

Remove the 4 nuts and No. 3 HV battery shield sub-assembly from the HV battery.


Hide G920G 18.REMOVE NO. 4 HV BATTERY END PLATE SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves.


a.
A406083C01
0.354,1.677 0.573,1.875 0.219,0.198 10 true *a 3.094,1.677 3.313,1.875 0.219,0.198 10 true *a 1.313,0.948 1.5,1.125 0.188,0.177 10 true *b 1.813,0.948 2,1.125 0.188,0.177 10 true *b
*a Bolt
*b Nut


Remove the 2 bolts, 2 nuts and No. 4 HV battery end plate sub-assembly from the HV battery.


Hide G920K 19.REMOVE NO. 5 HV BATTERY END PLATE SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves.


a.
A406084

Remove the 12 nuts and No. 5 HV battery end plate sub-assembly from the HV battery.


Hide G920NB 20.REMOVE UPPER HV BATTERY COVER SUB-ASSEMBLY

Hide G92Q1 21.REMOVE NO. 1 HV BATTERY SHIELD PANEL

Hide 89892A 22.REMOVE BATTERY VOLTAGE SENSOR

Hide G92Z2 23.REMOVE HYBRID BATTERY TERMINAL BLOCK

Hide G920R 25.REMOVE NO. 2 HYBRID BATTERY SHIELD SUB-ASSEMBLY

Hide G92E1A 26.REMOVE NO. 1 HV BATTERY INTAKE DUCT LH