Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › 2017.09–2021.02
RM33C0E _54 Brake _065446 PARKING BRAKE _0329402 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C13A1  Short Circuit in Power Source Circuit  


DESCRIPTION

The following DTCs are stored when a malfunction occurs in the parking brake ECU (brake actuator assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C13A1 Short Circuit in Power Source Circuit Both of following conditions are met:
1.

Power switch on (IG) or electric parking brake switch (electric parking brake switch assembly) pulled to lock side with power switch off.

2.

Parking brake ECU (brake actuator assembly) power source relay shorted for approximately 60 seconds.


·

Wire harness or connector

·

Electric parking brake switch (electric parking brake switch assembly)

·

Parking brake ECU (brake actuator assembly)


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Power switch on (IG) ○ -
Electric parking brake switch (electric parking brake switch assembly) pulled to lock side with power switch off - ○
Malfunction Status Parking brake ECU (brake actuator assembly) power source relay is shorted ○ ○
Detection Time Approximately 60 seconds Approximately 60 seconds
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C385552E03
1.396,1.063 2.771,1.26 1.375,0.198 10 false EPB NO. 1 1.25,1.698 3.083,1.896 1.833,0.198 10 false ECU-IG1 NO. 3 4.958,0.792 5.115,0.99 0.156,0.198 10 false 9 5.188,0.896 5.802,1.094 0.615,0.198 10 false BEPB 4.885,1.417 5.198,1.615 0.313,0.198 10 false 26 5.198,1.542 5.51,1.74 0.313,0.198 10 false IG 3.063,2.51 3.677,2.708 0.615,0.198 10 false SWI1 2.99,2.813 3.604,3.01 0.615,0.198 10 false SWO1 5.188,3.229 5.802,3.427 0.615,0.198 10 false SWI2 2.979,3.698 3.594,3.896 0.615,0.198 10 false SWO2 3.531,2.521 4.24,2.781 0.708,0.26 10 false 9*1, 16*2 3.521,2.802 4.229,3.021 0.708,0.219 10 false 10*1, 15*2 3.531,3.104 4.292,3.365 0.76,0.26 10 false 1*1, 8*2 3.531,3.698 4.292,3.896 0.76,0.198 10 false 2*1, 7*2 4.885,2.51 5.198,2.708 0.313,0.198 10 false 14 4.885,2.813 5.198,3.01 0.313,0.198 10 false 20 4.885,3.104 5.198,3.302 0.313,0.198 10 false 24 4.885,3.698 5.198,3.896 0.313,0.198 10 false 22 1.135,4.219 1.594,4.417 0.458,0.198 10 false K37 1.135,4.365 3.521,5.167 2.385,0.802 10 false Electric Parking Brake Switch (Electric Parking Brake Switch Assembly) 4.865,4.75 5.323,4.948 0.458,0.198 10 false A44 4.865,4.896 6.531,5.563 1.667,0.667 10 false Parking Brake ECU (Brake Actuator Assembly) 5.188,2.625 5.802,2.823 0.615,0.198 10 false SWI1 5.188,2.927 5.802,3.125 0.615,0.198 10 false SWO1 5.188,3.813 5.802,4.01 0.615,0.198 10 false SWO2 3.052,3.104 3.667,3.302 0.615,0.198 10 false SWI2 0.375,5.156 2.063,5.354 1.688,0.198 10 false *1: for LHD 0.375,5.427 2.063,5.625 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.

·

The parking brake indicator light blinks (red) when the power switch is turned on (IG) after replacing the parking brake ECU (brake actuator assembly). Operate the electric parking brake switch (electric parking brake switch assembly) to turn off the parking brake indicator light (red).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BEPB CIRCUIT)
a.

Turn the power switch off.


b.

Disconnect the A44 parking brake ECU (brake actuator assembly) connector.


c.
C379767C17
1.542,0.771 1.958,1.01 0.417,0.24 2.385,2.667 2.385,1.74 true 0.177,0.146 0.49,0.344 0.313,0.198 10 false *a 1.625,0.802 1.938,1 0.313,0.198 10 false A44 2.25,2.708 2.75,2.948 0.5,0.24 10 false BEPB
*a Front view of wire harness connector
(to Parking Brake ECU (Brake Actuator Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A44-9 (BEPB) - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - IG POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - IG POWER SOURCE CIRCUIT)
a.
C379767C13
1.479,0.74 1.927,0.99 0.448,0.25 2.021,2.771 2.021,2.021 false 0.125,0.146 0.438,0.344 0.313,0.198 10 false *a 1.573,0.781 1.885,0.979 0.313,0.198 10 false A44 1.979,2.792 2.292,2.99 0.313,0.198 10 false IG
*a Front view of wire harness connector
(to Parking Brake ECU (Brake Actuator Assembly))


Turn the power switch off.


b.

Disconnect the A44 parking brake ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A44-26 (IG) - Body ground Power switch off Below 2.5 V


Result:
Proceed to
OK
NG




OK

3.INSPECT ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
a.

Inspect the electric parking brake switch (electric parking brake switch assembly).

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))
a.

Disconnect the K37 electric parking brake switch (electric parking brake switch assembly) connector.


b.
C379767C19
1.5,0.74 1.958,1.01 0.458,0.271 2.5,2.667 2.031,1.875 true 0.833,2.667 1.417,2 true 2,2.667 1.823,1.969 true 1.417,2.667 1.625,2 true 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 1.625,0.802 1.938,1 0.313,0.198 10 false A44 0.583,2.677 1.281,2.938 0.698,0.26 10 false SWO1 1.208,2.688 1.667,2.99 0.458,0.302 10 false SWO2 1.833,2.688 2.24,2.969 0.406,0.281 10 false SWI2 2.406,2.688 2.833,2.99 0.427,0.302 10 false SWI1
*a Front view of wire harness connector
(to Parking Brake ECU (Brake Actuator Assembly))


Disconnect the A44 parking brake ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A44-14 (SWI1) - Body ground Always 10 kΩ or higher
A44-20 (SWO1) - Body ground Always 10 kΩ or higher
A44-24 (SWI2) - Body ground Always 10 kΩ or higher
A44-22 (SWO2) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR