Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › 2017.09–2019.02
RM33C0E _54 Brake _065446 PARKING BRAKE _0329402 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C13A6  Open or Short Circuit in Motor  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C13A6 Open or Short Circuit in Motor Both of following conditions are met:
1.

Power switch on (IG) or electric parking brake switch (electric parking brake switch assembly) pulled to lock side with power switch off.

2.

Power supply voltage and +B voltage are normal, but parking brake motor circuit is malfunctioning for approximately 1 to 2 seconds.


·

Parking brake actuator assembly

·

Wire harness or connector

·

Parking brake ECU (brake actuator assembly)


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Power switch on (IG) ○ -
Electric parking brake switch (electric parking brake switch assembly) pulled to lock side with power switch off - ○
Malfunction Status Voltage of power supplied to ECU is normal but malfunction exists in parking brake motor circuit ○ ○
Detection Time Approximately 1 to 2 seconds Approximately 1 to 2 seconds
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C320708E23
1.333,0.729 1.75,0.917 0.417,0.188 10 false MRR- 1.292,1.313 1.813,1.552 0.521,0.24 10 false MRR+ 1.313,3.875 1.729,4.063 0.417,0.188 10 false MRL+ 1.333,3.292 1.75,3.479 0.417,0.188 10 false MRL- 3.979,0.719 4.396,0.906 0.417,0.188 10 false MRR- 5.354,0.719 5.896,0.969 0.542,0.25 10 false RE- 3.979,1.302 4.396,1.49 0.417,0.188 10 false MRR+ 5.354,1.302 5.927,1.625 0.573,0.323 10 false RE+ 3.969,3.292 4.385,3.479 0.417,0.188 10 false MRL- 5.344,3.292 5.76,3.479 0.417,0.188 10 false LE- 3.958,3.896 4.375,4.083 0.417,0.188 10 false MRL+ 5.344,3.885 5.76,4.073 0.417,0.188 10 false LE+ 3.604,0.719 4.021,0.906 0.417,0.188 10 false uR2 3.604,1.313 4.021,1.5 0.417,0.188 10 false uR2 3.615,3.292 4.031,3.479 0.417,0.188 10 false vR2 3.625,3.885 4.042,4.073 0.417,0.188 10 false vR2 5.01,0.708 5.292,0.896 0.281,0.188 10 false u1 5.01,1.302 5.292,1.49 0.281,0.188 10 false u1 5.021,3.292 5.302,3.479 0.281,0.188 10 false v1 5.021,3.885 5.302,4.073 0.281,0.188 10 false v1 1.802,0.604 1.99,0.802 0.188,0.198 10 false 3 1.802,1.198 1.99,1.396 0.188,0.198 10 false 4 1.813,3.177 2,3.375 0.188,0.198 10 false 8 1.813,3.771 2,3.969 0.188,0.198 10 false 7 0.375,4.417 0.792,4.604 0.417,0.188 10 false A44 0.375,4.573 2.594,5.042 2.219,0.469 10 false Parking Brake ECU (Brake Actuator Assembly) 3.74,4.427 5.042,4.979 1.302,0.552 10 false NO. 2 Parking Brake Wire Assembly 5.115,4.417 6.552,4.927 1.438,0.51 10 false Parking Brake Actuator Assembly LH 3.677,1.833 4.979,2.302 1.302,0.469 10 false NO. 1 Parking Brake Wire Assembly 5.094,1.844 6.604,2.375 1.51,0.531 10 false Parking Brake Actuator Assembly RH 4.583,3.896 5,4.083 0.417,0.188 10 false LE+ 4.583,3.292 5,3.479 0.417,0.188 10 false LE- 4.573,1.302 4.99,1.49 0.417,0.188 10 false RE+ 4.604,0.719 5.021,0.906 0.417,0.188 10 false RE- 3.688,1.083 3.844,1.281 0.156,0.198 10 false 2 5.052,0.51 5.208,0.708 0.156,0.198 10 false 1 5.052,1.104 5.208,1.302 0.156,0.198 10 false 2 3.688,0.5 3.844,0.698 0.156,0.198 10 false 1 3.677,3.688 3.833,3.885 0.156,0.198 10 false 2 5.052,3.094 5.208,3.292 0.156,0.198 10 false 1 5.052,3.688 5.208,3.885 0.156,0.198 10 false 2 3.667,3.073 3.823,3.271 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.

·

The parking brake indicator light blinks (red) when the power switch is turned on (IG) after replacing the parking brake ECU (brake actuator assembly). Operate the electric parking brake switch (electric parking brake switch assembly) to turn off the parking brake indicator light (red).



PROCEDURE

1.READ VALUE USING GTS (PERMISSION OF RH INTERLOCKING PKB LOCK / PERMISSION OF LH INTERLOCKING PKB LOCK)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Electric Parking Brake / Data List.


f.

Read the Data List according to the display on the GTS.

Chassis > Electric Parking Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Permission of RH Interlocking PKB Lock Parking brake actuator assembly RH parking brake lock control permission status OK or NG OK -
Permission of LH Interlocking PKB Lock Parking brake actuator assembly RH parking brake lock control permission status OK or NG OK -
Chassis > Electric Parking Brake > Data List
Tester Display
Permission of RH Interlocking PKB Lock
Permission of LH Interlocking PKB Lock
50003 184 632,636
Result:
Proceed to
NEXT




NEXT

2.INSPECT PARKING BRAKE WIRE ASSEMBLY
2.INSPECT PARKING BRAKE WIRE ASSEMBLY
C360728C15
1.813,0.25 2.229,0.5 0.417,0.25 1.813,0.583 2.229,0.833 0.417,0.25 4.958,0.188 5.375,0.438 0.417,0.25 4.958,0.521 5.375,0.771 0.417,0.25 1.417,2.083 1.875,1.625 true 2.167,1.625 2.583,2.083 true 4.583,2.083 5,1.583 true 5.313,1.583 5.75,2.083 true 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 1.917,2.094 2.229,2.25 0.313,0.156 10 false *b 5.083,2.094 5.396,2.25 0.313,0.156 10 false *c 1.906,0.302 2.302,0.5 0.396,0.198 10 false uR2 1.917,0.635 2.375,0.833 0.458,0.198 10 false vR2 0.833,2.083 1.219,2.281 0.385,0.198 10 false MRR- 0.833,2.292 1.198,2.479 0.365,0.188 10 false MRL- 2.583,2.281 2.99,2.469 0.406,0.188 10 false MRL+ 2.583,2.083 3,2.302 0.417,0.219 10 false MRR+ 4.083,2.083 4.604,2.333 0.521,0.25 10 false RE- 4.083,2.292 4.604,2.542 0.521,0.25 10 false LE- 5.781,2.083 6.281,2.281 0.5,0.198 10 false RE+ 5.781,2.292 6.198,2.479 0.417,0.188 10 false LE+ 1.208,2.083 1.49,2.281 0.281,0.198 12 false *A 1.208,2.292 1.51,2.521 0.302,0.229 12 false *B 3,2.083 3.26,2.281 0.26,0.198 12 false *A 4.365,2.083 4.625,2.333 0.26,0.25 12 false *A 6.083,2.083 6.479,2.302 0.396,0.219 12 false *A 3,2.281 3.26,2.49 0.26,0.208 12 false *B 4.365,2.292 4.688,2.594 0.323,0.302 12 false *B 6.083,2.292 6.51,2.542 0.427,0.25 12 false *B 5.104,0.229 5.5,0.427 0.396,0.198 10 false u1 5.125,0.563 5.583,0.76 0.458,0.198 10 false v1 2.281,0.292 2.615,0.542 0.333,0.25 12 false *A 2.281,0.625 2.531,0.875 0.25,0.25 12 false *B 5.438,0.219 5.771,0.469 0.333,0.25 12 false *A 5.438,0.563 5.688,0.813 0.25,0.25 12 false *B
*A RH *B LH
*a Front view of Parking Brake Wire Assembly *b (to wire harness connector)
*c (to Parking Brake Actuator Assembly) - -


a.

Remove the parking brake wire assembly.


b.

Check the parking brake wire assembly for damage.

OK:

No damage.


HINT:

If damaged, there may be a short in the wire harness or a short to ground.



c.

Inspect the parking brake wire assembly.

Standard Resistance:
RH
Tester Connection Condition Specified Condition
uR2-1 (MRR-) - u1-1 (RE-) Always Below 1 Ω
uR2-1 (MRR-) - u1-2 (RE+) Always 10 kΩ or higher
uR2-1 (MRR-) or u1-1 (RE-) - Body ground Always 10 kΩ or higher
uR2-2 (MRR+) - u1-2 (RE+) Always Below 1 Ω
uR2-2 (MRR+) - u1-1 (RE-) Always 10 kΩ or higher
uR2-2 (MRR+) or u1-2 (RE+) - Body ground Always 10 kΩ or higher

LH
Tester Connection Condition Specified Condition
vR2-1 (MRL-) - v1-1 (LE-) Always Below 1 Ω
vR2-1 (MRL-) - v1-2 (LE+) Always 10 kΩ or higher
vR2-1 (MRL-) or v1-1 (LE-) - Body ground Always 10 kΩ or higher
vR2-2 (MRL+) - v1-2 (LE+) Always Below 1 Ω
vR2-2 (MRL+) - v1-1 (LE-) Always 10 kΩ or higher
vR2-2 (MRL+) or v1-2 (LE+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE PARKING BRAKE WIRE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY)
a.

Turn the power switch off.


b.

Make sure the parking brake wire assembly is securely installed.


c.

Disconnect the A44 parking brake ECU (brake actuator assembly) connector.


d.

Disconnect the u1 or v1 parking brake actuator assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
RH
Tester Connection Condition Specified Condition
A44-4 (MRR+) - u1-2 (RE+) Always Below 1 Ω
A44-3 (MRR-) - u1-1 (RE-) Always Below 1 Ω
A44-4 (MRR+) or u1-2 (RE+) - Body ground Always 10 kΩ or higher
A44-3 (MRR-) or u1-1 (RE-) - Body ground Always 10 kΩ or higher

LH
Tester Connection Condition Specified Condition
A44-7 (MRL+) - v1-2 (LE+) Always Below 1 Ω
A44-8 (MRL-) - v1-1 (LE-) Always Below 1 Ω
A44-7 (MRL+) or v1-2 (LE+) - Body ground Always 10 kΩ or higher
A44-8 (MRL-) or v1-1 (LE-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY
a.

Inspect the parking brake actuator assembly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY