Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM33C0E _55 Steering _065447 POWER ASSIST SYSTEMS _0329532 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1567  Error in Matching of ECUs  


DESCRIPTION

The power steering ECU (rack and pinion power steering gear assembly) determines whether an incompatible hybrid vehicle control ECU assembly, main body ECU (multiplex network body ECU) or skid control ECU (brake booster with master cylinder assembly) is installed based on the identification information.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition Note
C1567 Error in Matching of ECUs
·

An incompatible hybrid vehicle control ECU assembly is detected

·

An incompatible main body ECU (multiplex network body ECU) is detected

·

An incompatible skid control ECU (brake booster with master cylinder assembly) is detected


·

Incorrect hybrid vehicle control ECU assembly

·

Incorrect main body ECU (multiplex network body ECU)

·

Incorrect skid control ECU (brake booster with master cylinder assembly)

·

Rack and pinion power steering gear assembly


EPS warning light: Comes on The ECU judges the system has returned to normal or the power switch is turned on (IG) again -

CAUTION / NOTICE / HINT

NOTICE:

If the rack and pinion power steering gear assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION


PROCEDURE

1.CHECK RELATED PART
a.

Confirm if the related part has the correct part number.

Related Part Hybrid vehicle control ECU assembly
Main body ECU (Multiplex network body ECU)
Skid control ECU (Brake booster with master cylinder assembly)

NOTICE:

When removing the related part to check it, be sure to follow the appropriate procedures and precautions.

·

Main body ECU (Multiplex network body ECU)

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

·

Skid control ECU (Brake booster with master cylinder assembly)

for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL




Result:
Result Proceed to
The related part has the correct part number. A
The related part has an incorrect part number. B



A

2.CHECK FOR DTC

B

3.REPLACE RELATED PART WITH PART THAT HAS CORRECT PART NUMBER
2.CHECK FOR DTC
a.

Select Health Check on the GTS screen and check if system DTCs of the related part are output.

HINT:

If system DTCs of the related part are stored, assist map writing to the power steering ECU (rack and pinion power steering gear assembly) may not be performed properly.



Result:
Result Proceed to
System DTCs of the related part are output. A
System DTCs of the related part are not output. B



A

GO TO DIAGNOSTIC PROCEDURE INDICATED BY OUTPUT DTC

B

REPLACE RACK AND PINION POWER STEERING GEAR ASSEMBLY

3.REPLACE RELATED PART WITH PART THAT HAS CORRECT PART NUMBER
a.

Replace the related part with one that has the correct part number.

·

Main body ECU (Multiplex network body ECU)

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

·

Skid control ECU (Brake booster with master cylinder assembly)

for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL



Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Check for DTCs.

Chassis > EMPS > Trouble Codes
50001 142

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

END

B

REPLACE RACK AND PINION POWER STEERING GEAR ASSEMBLY