Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM
RM33C0E _56 Audio / Visual / Telematics _065452 PARK ASSIST / MONITORING _0329721 PARKING ASSIST MONITOR SYSTEM C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  C1621  Back Camera Power Supply Failure  


DESCRIPTION

This DTC is stored if the rear television camera assembly judges as a result of its self check that the signals or signal lines between the rear television camera assembly and radio and display assembly are not normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1621 Back Camera Power Supply Failure Rear television camera assembly power supply failure
·

Harness or connector

·

Rear television camera assembly

·

Radio and display receiver assembly



WIRING DIAGRAM

E378706E03
1.615,0.688 2.104,0.906 0.49,0.219 10 false CA+ 1.479,1.177 1.969,1.396 0.49,0.219 10 false CGND 1.99,0.583 2.479,0.802 0.49,0.219 10 false 30 1.99,1.052 2.479,1.271 0.49,0.219 10 false 27 5.094,1.063 5.583,1.281 0.49,0.219 10 false 5 5.094,0.583 5.583,0.802 0.49,0.219 10 false 6 4.969,1.698 5.458,1.917 0.49,0.219 10 false m3 4.969,1.865 6.427,2.271 1.458,0.406 10 false Rear Television Camera Assembly 0.75,1.708 1.24,1.927 0.49,0.219 10 false K2 0.74,1.875 2.427,2.271 1.688,0.396 10 false Radio and Display Receiver Assembly 5.281,0.708 5.771,0.927 0.49,0.219 10 false CB+ 5.281,1.188 5.771,1.406 0.49,0.219 10 false CGND

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the K2 radio and display receiver assembly connector.


b.

Disconnect the m3 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-30 (CA+) - m3-6 (CB+) Always Below 1 Ω
K2-27 (CGND) - m3-5 (CGND) Always Below 1 Ω
K2-30 (CA+) or m3-6 (CB+) - Body ground Always 10 kΩ or higher
K2-27 (CGND) or m3-5 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Reconnect the K2 radio and display receiver assembly connector.


b.
E366062C05
1.427,0.198 1.917,0.479 0.49,0.281 0.542,1.073 1.042,1.344 true 1.333,1.875 1.438,1.375 true 1.583,0.25 1.896,0.448 0.313,0.198 10 false K2 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a 0.24,0.958 0.698,1.156 0.458,0.198 10 false CA+ 1.156,1.896 1.771,2.094 0.615,0.198 10 false CGND
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-27 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K2-30 (CA+) - K2-27 (CGND) Power switch on (ACC) 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY