Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2017.09–2017.12
RM33C0E _58 Vehicle Interior _065458 METER / GAUGE / DISPLAY _0330016 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B150718  Turn Signal Light Circuit Current Below Threshold  


DESCRIPTION

This DTC is stored when the combination meter assembly detects an open in a front turn signal light circuit or rear turn signal light circuit.

HINT:
·

If there is an open in a front turn signal light circuit or rear turn signal light circuit, the turn signal lights on the side with the open circuit will blink faster than usual.

·

If there is an open in a side turn signal light circuit, DTC B150718 will not be stored.



DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B150718 Turn Signal Light Circuit Current Below Threshold Diagnosis Condition:

Auxiliary battery voltage is 10 V or more


Malfunction Status:
·

Open in front turn signal light circuit

·

Open in rear turn signal light circuit


·

Headlight ECU sub-assembly

·

Head light unit assembly

·

Headlight lens

·

Rear combination light assembly*1

·

Rear combination light cord*1

·

Rear combination light socket and wire*2

·

Harness or connector

·

Combination meter assembly


DTC stored -

*1: for LED Type Back-up Light

*2: for Bulb Type Back-up Light


WIRING DIAGRAM

LH side



E380800E01
5.344,0.417 5.656,0.615 0.313,0.198 10 false 11 5.615,0.417 5.927,0.615 0.313,0.198 10 false LL 2.031,0.417 2.188,0.615 0.156,0.198 10 false 9 1.969,0.771 2.281,0.969 0.313,0.198 10 false 13 3.74,0.417 4.052,0.615 0.313,0.198 10 false 11 3.74,0.771 4.052,0.969 0.313,0.198 10 false 12 2.24,0.417 3.01,0.615 0.771,0.198 10 false TURN+ 2.24,0.771 3.01,0.969 0.771,0.198 10 false TURN- 3.344,0.417 3.802,0.615 0.458,0.198 10 false TNS 3.313,0.771 3.771,0.969 0.458,0.198 10 false GND 6.167,2 6.854,2.542 0.688,0.542 10 false FLASHER IC 0.573,1.125 3.177,1.323 2.604,0.198 10 false Headlight Lens LH 0.313,1.573 1.208,2.219 0.896,0.646 10 false Headlight Unit Assembly LH 1.573,1.635 1.729,1.833 0.156,0.198 10 false B 1.573,1.781 6.01,1.979 4.438,0.198 10 false Headlight ECU Sub-assembly LH 1.146,2.438 1.604,2.635 0.458,0.198 10 false A10 1.552,2.438 4.76,2.635 3.208,0.198 10 false Headlight Assembly LH 5.333,3.104 5.646,3.302 0.313,0.198 10 false 10 5.615,3.104 6.229,3.302 0.615,0.198 10 false TRNL 4.917,3.104 5.229,3.302 0.313,0.198 10 false *1 4.896,4.875 5.208,5.073 0.313,0.198 10 false *2 3.229,3.104 3.385,3.302 0.156,0.198 10 false 3 3.229,4.875 3.385,5.073 0.156,0.198 10 false 3 3.24,5.229 3.396,5.427 0.156,0.198 10 false 4 3.24,3.458 3.396,3.656 0.156,0.198 10 false 4 3.01,3.448 3.167,3.646 0.156,0.198 10 false E 3.01,5.229 3.167,5.427 0.156,0.198 10 false E 3.01,3.104 3.167,3.302 0.156,0.198 10 false B 3.01,4.875 3.167,5.073 0.156,0.198 10 false B 1.083,3.813 5.667,4.01 4.583,0.198 10 false Rear Combination Light Cord LH 0.417,4.281 0.875,4.479 0.458,0.198 10 false W13 0.802,4.271 6,4.469 5.198,0.198 10 false Rear Combination Light Assembly LH 0.365,5.573 6.635,5.771 6.271,0.198 10 false Rear Combination Light Socket and Wire LH 0.406,6.052 0.865,6.25 0.458,0.198 10 false W13 0.781,6.052 5.979,6.25 5.198,0.198 10 false Rear Combination Light Assembly LH 5.49,4.698 5.948,4.896 0.458,0.198 10 false K20 5.813,4.698 7,5.271 1.188,0.573 10 false Combination Meter Assembly 4.698,6.01 7.021,6.479 2.323,0.469 10 false *1: for LED Type Back-up Light 4.698,6.396 6.854,6.833 2.156,0.438 10 false *2: for Bulb Type Back-up Light

RH side


E380800E02
5.344,0.417 5.656,0.615 0.313,0.198 10 false 11 5.615,0.417 5.927,0.615 0.313,0.198 10 false LR 2.031,0.417 2.188,0.615 0.156,0.198 10 false 9 1.969,0.771 2.281,0.969 0.313,0.198 10 false 13 3.74,0.417 4.052,0.615 0.313,0.198 10 false 11 3.74,0.771 4.052,0.969 0.313,0.198 10 false 12 2.24,0.406 3.01,0.604 0.771,0.198 10 false TURN+ 2.24,0.76 3.01,0.958 0.771,0.198 10 false TURN- 3.344,0.406 3.802,0.604 0.458,0.198 10 false TNS 3.313,0.771 3.771,0.969 0.458,0.198 10 false GND 6.167,2 6.854,2.542 0.688,0.542 10 false FLASHER IC 0.573,1.125 3.177,1.323 2.604,0.198 10 false Headlight Lens RH 0.313,1.573 1.208,2.219 0.896,0.646 10 false Headlight Unit Assembly RH 1.552,1.635 1.708,1.833 0.156,0.198 10 false B 1.552,1.781 5.99,1.979 4.438,0.198 10 false Headlight ECU Sub-assembly RH 1.146,2.438 1.604,2.635 0.458,0.198 10 false A11 1.552,2.438 4.76,2.635 3.208,0.198 10 false Headlight Assembly RH 5.333,3.104 5.646,3.302 0.313,0.198 10 false 10 5.615,3.104 6.229,3.302 0.615,0.198 10 false TRNR 4.917,3.104 5.229,3.302 0.313,0.198 10 false *1 4.896,4.885 5.208,5.083 0.313,0.198 10 false *2 3.229,3.104 3.385,3.302 0.156,0.198 10 false 3 3.229,4.875 3.385,5.073 0.156,0.198 10 false 3 3.24,5.229 3.396,5.427 0.156,0.198 10 false 4 3.24,3.458 3.396,3.656 0.156,0.198 10 false 4 3.01,3.448 3.167,3.646 0.156,0.198 10 false E 3.01,5.229 3.167,5.427 0.156,0.198 10 false E 3.01,3.104 3.167,3.302 0.156,0.198 10 false B 3.01,4.875 3.167,5.073 0.156,0.198 10 false B 1.083,3.813 5.667,4.01 4.583,0.198 10 false Rear Combination Light Cord RH 0.417,4.281 0.875,4.479 0.458,0.198 10 false W12 0.802,4.271 6,4.469 5.198,0.198 10 false Rear Combination Light Assembly RH 0.365,5.573 6.635,5.771 6.271,0.198 10 false Rear Combination Light Socket and Wire RH 0.406,6.052 0.865,6.25 0.458,0.198 10 false W12 0.781,6.052 5.979,6.25 5.198,0.198 10 false Rear Combination Light Assembly RH 5.49,4.698 5.948,4.896 0.458,0.198 10 false K20 5.813,4.698 7,5.271 1.188,0.573 10 false Combination Meter Assembly 4.698,6.01 7.021,6.479 2.323,0.469 10 false *1: for LED Type Back-up Light 4.698,6.396 6.854,6.833 2.156,0.438 10 false *2: for Bulb Type Back-up Light


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC maybe stored.

·

Inspect the turn signal light bulbs and sockets before performing the following procedure.



PROCEDURE

1.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.


Result:
Result Proceed to
Front turn signal light LH does not blink A
Rear turn signal light LH does not blink B
Front turn signal light RH does not blink C
Rear turn signal light RH does not blink D



A

2.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

B

6.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

C

11.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

D

15.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the A10 headlight assembly LH connector.


b.

Disconnect the K20 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A10-11 (TNS) - K20-11 (LL) Always Below 1 Ω
A10-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH
E334043C09
2.156,0.219 2.458,0.427 0.302,0.208 5.604,0.323 5.906,0.531 0.302,0.208 1.219,0.302 1.646,0.813 true 3.146,0.865 3.458,0.323 true 5.323,0.979 5.083,0.385 true 6.052,1.104 6.448,0.385 true 0.094,0.115 0.406,0.313 0.313,0.198 10 false *a 2.188,0.229 2.5,0.427 0.313,0.198 10 false A10 5.708,0.333 6.021,0.531 0.313,0.198 10 false B 1.073,0.115 1.385,0.313 0.313,0.198 10 false TNS 3.354,0.146 3.667,0.344 0.313,0.198 10 false GND 4.875,0.198 5.406,0.417 0.531,0.219 10 false TURN+ 6.271,0.198 6.823,0.417 0.552,0.219 10 false TURN-
*a Component without harness connected
(Headlight ECU Sub-assembly LH)
- -


a.

Remove the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-9 (TURN+) - A10-11 (TNS) Always Below 1 Ω
B-13 (TURN-) - A10-12 (GND) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HEADLIGHT UNIT ASSEMBLY LH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

4.CHECK HEADLIGHT UNIT ASSEMBLY LH
a.

Remove each headlight ECU sub-assembly, interchange the headlight unit assembly LH with RH and connect the connectors.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY


b.

Check that the front turn signal light operates normally.

OK:

Front turn signal light blinks.



Result:
Proceed to
OK
NG



OK

5.INSPECT HEADLIGHT LENS LH

NG

REPLACE COMBINATION METER ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the W13 rear combination light assembly LH connector.


b.

Disconnect the K20 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W13-3 (B) - K20-10 (TRNL) Always Below 1 Ω
W13-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CONFIRM MODEL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for LED Type Back-up Light A
for Bulb Type Back-up Light B



A

8.CHECK REAR COMBINATION LIGHT CORD LH

B

10.CHECK REAR COMBINATION LIGHT SOCKET AND WIRE LH
8.CHECK REAR COMBINATION LIGHT CORD LH
a.

Interchange the rear combination light cord LH with RH and connect the connectors.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY


b.

Check that the rear turn signal light operates normally.

OK:

Rear turn signal light blinks.



Result:
Proceed to
OK
NG



OK

REPLACE REAR COMBINATION LIGHT CORD LH

NG

9.INSPECT REAR COMBINATION LIGHT ASSEMBLY LH
9.INSPECT REAR COMBINATION LIGHT ASSEMBLY LH
a.

Remove the rear combination light assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>REMOVAL


b.

Inspect the rear combination light assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE REAR COMBINATION LIGHT ASSEMBLY LH

10.CHECK REAR COMBINATION LIGHT SOCKET AND WIRE LH
a.

Interchange the rear combination light socket and wire LH with RH and connect the connectors.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>REMOVAL


b.

Check that the rear turn signal light operates normally.

OK:

Rear turn signal light blinks.



Result:
Proceed to
OK
NG



OK

REPLACE REAR COMBINATION LIGHT SOCKET AND WIRE LH

NG

REPLACE COMBINATION METER ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the A11 headlight assembly RH connector.


b.

Disconnect the K20 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A11-11 (TNS) - K20-11 (LR) Always Below 1 Ω
A11-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH
E334043C10
2.156,0.219 2.458,0.427 0.302,0.208 5.604,0.323 5.906,0.531 0.302,0.208 1.219,0.302 1.646,0.813 true 3.146,0.865 3.458,0.323 true 5.323,0.979 5.083,0.385 true 6.052,1.104 6.448,0.385 true 0.094,0.115 0.406,0.313 0.313,0.198 10 false *a 2.198,0.25 2.51,0.448 0.313,0.198 10 false A11 5.719,0.344 6.031,0.542 0.313,0.198 10 false B 1.073,0.115 1.385,0.313 0.313,0.198 10 false TNS 3.354,0.135 3.667,0.333 0.313,0.198 10 false GND 4.875,0.188 5.417,0.396 0.542,0.208 10 false TURN+ 6.25,0.198 6.729,0.448 0.479,0.25 10 false TURN-
*a Component without harness connected
(Headlight ECU Sub-assembly RH)
- -


a.

Remove the headlight ECU sub-assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-9 (TURN+) - A11-11 (TNS) Always Below 1 Ω
B-13 (TURN-) - A11-12 (GND) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK HEADLIGHT UNIT ASSEMBLY RH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

13.CHECK HEADLIGHT UNIT ASSEMBLY RH
a.

Remove each headlight ECU sub-assembly, interchange the headlight unit assembly RH with LH and connect the connectors.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY


b.

Check that the front turn signal light operates normally.

OK:

Front turn signal light blinks.



Result:
Proceed to
OK
NG



OK

14.INSPECT HEADLIGHT LENS RH

NG

REPLACE COMBINATION METER ASSEMBLY

15.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the W12 rear combination light assembly RH connector.


b.

Disconnect the K20 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W12-3 (B) - K20-10 (TRNR) Always Below 1 Ω
W12-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

16.CONFIRM MODEL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for LED Type Back-up Light A
for Bulb Type Back-up Light B



A

17.CHECK REAR COMBINATION LIGHT CORD RH

B

19.CHECK REAR COMBINATION LIGHT SOCKET AND WIRE RH
17.CHECK REAR COMBINATION LIGHT CORD RH
a.

Interchange the rear combination light cord RH with LH and connect the connectors.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY


b.

Check that the rear turn signal light operates normally.

OK:

Rear turn signal light blinks.



Result:
Proceed to
OK
NG



OK

REPLACE REAR COMBINATION LIGHT CORD RH

NG

18.INSPECT REAR COMBINATION LIGHT ASSEMBLY RH
18.INSPECT REAR COMBINATION LIGHT ASSEMBLY RH
a.

Remove the rear combination light assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>INSPECTION


b.

Inspect the rear combination light assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE REAR COMBINATION LIGHT ASSEMBLY RH

19.CHECK REAR COMBINATION LIGHT SOCKET AND WIRE RH
a.

Interchange the rear combination light socket and wire RH with LH and connect the connectors.


b.

Check that the rear turn signal light operates normally.

OK:

Rear turn signal light blinks.



Result:
Proceed to
OK
NG



OK

REPLACE REAR COMBINATION LIGHT SOCKET AND WIRE RH

NG

REPLACE COMBINATION METER ASSEMBLY