Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System) › 2017.09–2017.12
RM33C0E _59 Vehicle Exterior _065472 LIGHTING (EXT) _0331112 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B2439  Headlight LH Circuit  B243A  Headlight RH Circuit  


DESCRIPTION

The headlight ECU sub-assembly LH and headlight ECU sub-assembly RH internally boost the power supply voltage to ensure a constant supplied current for the lo/hi beam LED of their respective headlight.

By monitoring the LED power supply voltage, abnormal current and malfunctions can be detected.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B2439 Headlight LH Circuit
Detection condition:

All of the following conditions are met:

-

Power switch on (IG)

-

Low beam headlights on



Malfunction status:
·

Headlight unit malfunction

·

Open/short in Lo/Hi beam circuit


Malfunction duration:

10 seconds or more


·

Headlight unit LH

·

Headlight unit assembly LH

·

Headlight ECU sub-assembly LH


Headlight ECU sub-assembly LH
B243A Headlight RH Circuit
Detection condition:

All of the following conditions are met:

-

Power switch on (IG)

-

Low beam headlights on



Malfunction status:
·

Headlight unit malfunction

·

Open/short in Lo/Hi beam circuit


Malfunction duration:

10 seconds or more


·

Headlight unit RH

·

Headlight unit assembly RH

·

Headlight ECU sub-assembly RH


Headlight ECU sub-assembly RH

WIRING DIAGRAM

E333074E33
0.229,3.271 2.271,3.583 2.042,0.313 10 false Headlight ECU Sub-assembly 3.094,2.938 4.74,3.375 1.646,0.438 10 false Headlight Unit Assembly 5.031,2.458 6.667,2.688 1.635,0.229 10 false Headlight Unit 5.49,1.469 6.573,1.76 1.083,0.292 10 false Lo/Hi Beam 1.552,1.219 1.771,1.417 0.219,0.198 10 false 4 1.552,1.615 1.771,1.833 0.219,0.219 10 false 5 4.448,1.219 4.604,1.417 0.156,0.198 10 false 5 4.448,1.625 4.604,1.823 0.156,0.198 10 false 6 5.021,2.292 5.177,2.49 0.156,0.198 10 false C 0.219,3.125 0.375,3.323 0.156,0.198 10 false B 0.927,1.313 1.615,1.542 0.688,0.229 10 false LOLED2 0.927,1.719 1.615,1.948 0.688,0.229 10 false LOLED1

CAUTION / NOTICE / HINT

NOTICE:

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System)>INITIALIZATION


PROCEDURE

1.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.


e.

Clear the DTCs.

Body Electrical > HL AutoLeveling > Clear DTCs
50002 361
Body Electrical > HL AutoLeveling (Sub) > Clear DTCs
50002 414

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Operate the light control switch to turn on the low beam headlights and wait 10 seconds or more.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.


f.

Check for DTCs.

Body Electrical > HL AutoLeveling > Trouble Codes
50001 361
Body Electrical > HL AutoLeveling (Sub) > Trouble Codes
50001 414
OK:

DTC B2439 and B243A are not output.



Result:
Result Proceed to
OK A
NG (DTC B2439 is output) B
NG (DTC B243A is output) C



A

B

3.CHECK HEADLIGHT UNIT ASSEMBLY LH

C

7.CHECK HEADLIGHT UNIT ASSEMBLY RH
3.CHECK HEADLIGHT UNIT ASSEMBLY LH
a.

Interchange the headlight unit assembly LH with RH and connect the connectors.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.


e.

Clear the DTCs.

Body Electrical > HL AutoLeveling > Clear DTCs
50002 361
Body Electrical > HL AutoLeveling (Sub) > Clear DTCs
50002 414

Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Operate the light control switch to turn on the low beam headlights and wait 10 seconds or more.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.


f.

Check for DTCs.

Body Electrical > HL AutoLeveling > Trouble Codes
50001 361
Body Electrical > HL AutoLeveling (Sub) > Trouble Codes
50001 414

Result:
Result Proceed to
DTC B2439 is output A
DTC B243A is output B



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

B

6.INSPECT HEADLIGHT UNIT ASSEMBLY LH
6.INSPECT HEADLIGHT UNIT ASSEMBLY LH
E371562C04
1.833,0.354 2.198,0.656 0.365,0.302 4.896,0.375 5.26,0.677 0.365,0.302 1.354,2.083 1.76,1.406 false 2.042,2.094 1.917,1.396 false 0.615,0.438 0.927,0.635 0.313,0.198 10 false *a 4.115,0.469 4.427,0.667 0.313,0.198 10 false *b 1.969,0.417 2.281,0.615 0.313,0.198 10 false B 5.031,0.458 5.344,0.656 0.313,0.198 10 false C 1.115,2.125 1.792,2.344 0.677,0.219 10 false LOLED2 1.865,2.125 2.542,2.344 0.677,0.219 10 false LOLED1
*a Component without harness connected
(to Headlight ECU Sub-assembly LH)
*b Component without harness connected
(to Headlight Unit LH)




c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-4 (LOLED2) - C-5 Always Below 1 Ω
B-5 (LOLED1) - C-6 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

7.CHECK HEADLIGHT UNIT ASSEMBLY RH
a.

Interchange the headlight unit assembly RH with LH and connect the connectors.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC
8.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.


e.

Clear the DTCs.

Body Electrical > HL AutoLeveling > Clear DTCs
50002 361
Body Electrical > HL AutoLeveling (Sub) > Clear DTCs
50002 414

Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Operate the light control switch to turn on the low beam headlights and wait 10 seconds or more.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.


f.

Check for DTCs.

Body Electrical > HL AutoLeveling > Trouble Codes
50001 361
Body Electrical > HL AutoLeveling (Sub) > Trouble Codes
50001 414

Result:
Result Proceed to
DTC B243A is output A
DTC B2439 is output B



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

B

10.INSPECT HEADLIGHT UNIT ASSEMBLY RH
10.INSPECT HEADLIGHT UNIT ASSEMBLY RH
E371562C04
1.833,0.354 2.198,0.656 0.365,0.302 4.896,0.375 5.26,0.677 0.365,0.302 1.354,2.083 1.76,1.406 false 2.042,2.094 1.917,1.396 false 0.615,0.438 0.927,0.635 0.313,0.198 10 false *a 4.115,0.469 4.427,0.667 0.313,0.198 10 false *b 1.969,0.417 2.281,0.615 0.313,0.198 10 false B 5.031,0.458 5.344,0.656 0.313,0.198 10 false C 1.115,2.125 1.792,2.344 0.677,0.219 10 false LOLED2 1.865,2.125 2.542,2.344 0.677,0.219 10 false LOLED1
*a Component without harness connected
(to Headlight ECU Sub-assembly RH)
*b Component without harness connected
(to Headlight Unit RH)




c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-4 (LOLED2) - C-5 Always Below 1 Ω
B-5 (LOLED1) - C-6 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG