Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System) › 2017.09–2017.12
RM33C0E _59 Vehicle Exterior _065472 LIGHTING (EXT) _0331112 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B243D  Left Low Beam Fan Malfunction  B243E  Right Low Beam Fan Malfunction  


DESCRIPTION

The headlight ECU sub-assembly operates the low beam fan to cool the headlight LED unit in order to prevent the headlight LED unit from overheating.

Illuminates the low beam headlights and continuously operates the low beam fan.

The headlight ECU sub-assembly monitors the pulse signals from the FANP terminal when the low beam fans are operating.

HINT:

If B243D or B243E is output, the headlight ECU sub-assembly performs low beam headlight dimming control.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B243D Left Low Beam Fan Malfunction
Detection condition:

All of the following conditions are met:

-

Power switch on (IG)

-

Low beam headlights on



Malfunction status:

Fan speed signals from the low beam fan of less than 1600 rpm are continuously detected


Malfunction duration:

120 seconds or more


·

Headlight unit LH

·

Headlight unit assembly LH

·

Headlight ECU sub-assembly LH


Headlight ECU sub-assembly LH
B243E Right Low Beam Fan Malfunction
Detection condition:

All of the following conditions are met:

-

Power switch on (IG)

-

Low beam headlights on



Malfunction status:

Fan speed signals from the low beam fan of less than 1600 rpm are continuously detected


Malfunction duration:

120 seconds or more


·

Headlight unit RH

·

Headlight unit assembly RH

·

Headlight ECU sub-assembly RH


Headlight ECU sub-assembly RH

WIRING DIAGRAM

E335162E38
0.208,3.333 2.167,3.646 1.958,0.313 10 false Headlight ECU Sub-assembly 3.104,2.948 4.792,3.354 1.688,0.406 10 false Headlight Unit Assembly 5.76,1.49 6.781,1.719 1.021,0.229 10 false Headlight Fan 1.583,1.24 1.823,1.469 0.24,0.229 10 false 6 1.542,1.448 1.896,1.656 0.354,0.208 10 false 15 1.542,1.677 1.844,1.927 0.302,0.25 10 false 14 4.396,1.24 4.615,1.396 0.219,0.156 10 false 12 4.438,1.677 4.604,1.896 0.167,0.219 10 false 4 4.396,1.458 4.625,1.635 0.229,0.177 10 false 11 0.219,3.188 0.406,3.354 0.188,0.167 10 false B 5.094,2.292 5.25,2.49 0.156,0.198 10 false C 5.073,2.438 6.635,2.688 1.563,0.25 10 false Headlight Unit 1.094,1.313 1.5,1.521 0.406,0.208 10 false FANB 1.094,1.542 1.5,1.75 0.406,0.208 10 false FANP 1.083,1.771 1.49,1.979 0.406,0.208 10 false FANG

CAUTION / NOTICE / HINT

NOTICE:

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System)>INITIALIZATION


PROCEDURE

1.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.


e.

Clear the DTCs.

Body Electrical > HL AutoLeveling > Clear DTCs
50002 361
Body Electrical > HL AutoLeveling (Sub) > Clear DTCs
50002 414

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Operate the light control switch to turn on the low beam headlights and wait 120 seconds or more.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.


f.

Check for DTCs.

Body Electrical > HL AutoLeveling > Trouble Codes
50001 361
Body Electrical > HL AutoLeveling (Sub) > Trouble Codes
50001 414
OK:

DTC B243D and B243E are not output.



Result:
Result Proceed to
OK A
NG (DTC B243D is output) B
NG (DTC B243E is output) C



A

B

3.INSPECT HEADLIGHT UNIT ASSEMBLY LH

C

5.INSPECT HEADLIGHT UNIT ASSEMBLY RH
3.INSPECT HEADLIGHT UNIT ASSEMBLY LH
E371562C05
1.833,0.354 2.198,0.656 0.365,0.302 4.896,0.375 5.26,0.677 0.365,0.302 2.521,2.094 2.083,1.417 false 1.521,2.073 1.75,1.563 false 2.083,2.063 1.927,1.563 false 0.615,0.438 0.927,0.635 0.313,0.198 10 false *a 4.115,0.469 4.427,0.667 0.313,0.198 10 false *b 1.969,0.417 2.281,0.615 0.313,0.198 10 false B 5.031,0.458 5.344,0.656 0.313,0.198 10 false C 1.333,2.115 2.01,2.333 0.677,0.219 10 false FANG 2.427,2.115 3.104,2.333 0.677,0.219 10 false FANB 1.958,2.115 2.635,2.333 0.677,0.219 10 false FANP
*a Component without harness connected
(to Headlight ECU Sub-assembly LH)
*b Component without harness connected
(to Headlight Unit LH)




c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-6 (FANB) - C-12 Always Below 1 Ω
B-15 (FANP) - C-11 Always Below 1 Ω
B-14 (FANG) - C-4 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT HEADLIGHT ECU SUB-ASSEMBLY LH

NG

4.INSPECT HEADLIGHT ECU SUB-ASSEMBLY LH
E371100C02
1.5,0.771 1.885,1.042 0.385,0.271 0.49,0.49 0.802,0.688 0.313,0.198 10 false *a 1.656,0.823 1.969,1.021 0.313,0.198 10 false C
*a Component without harness connected
(to Headlight Unit LH)


a.

Connect the B headlight ECU sub-assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C-12 - C-4 Low beam headlights on 4.75 to 5.25 V
C-11 - C-4 Low beam headlights on 4.75 to 5.25 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

5.INSPECT HEADLIGHT UNIT ASSEMBLY RH
E371562C05
1.833,0.354 2.198,0.656 0.365,0.302 4.896,0.375 5.26,0.677 0.365,0.302 2.521,2.094 2.083,1.417 false 1.521,2.073 1.75,1.563 false 2.083,2.063 1.927,1.563 false 0.615,0.438 0.927,0.635 0.313,0.198 10 false *a 4.115,0.469 4.427,0.667 0.313,0.198 10 false *b 1.969,0.417 2.281,0.615 0.313,0.198 10 false B 5.031,0.458 5.344,0.656 0.313,0.198 10 false C 1.333,2.115 2.01,2.333 0.677,0.219 10 false FANG 2.427,2.115 3.104,2.333 0.677,0.219 10 false FANB 1.958,2.115 2.635,2.333 0.677,0.219 10 false FANP
*a Component without harness connected
(to Headlight ECU Sub-assembly RH)
*b Component without harness connected
(to Headlight Unit RH)




c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-6 (FANB) - C-12 Always Below 1 Ω
B-15 (FANP) - C-11 Always Below 1 Ω
B-14 (FANG) - C-4 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH

NG

6.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH
E371100C02
1.5,0.771 1.885,1.042 0.385,0.271 0.49,0.49 0.802,0.688 0.313,0.198 10 false *a 1.656,0.823 1.969,1.021 0.313,0.198 10 false C
*a Component without harness connected
(to Headlight Unit RH)


a.

Connect the B headlight ECU sub-assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C-12 - C-4 Low beam headlights on 4.75 to 5.25 V
C-11 - C-4 Low beam headlights on 4.75 to 5.25 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH