Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System) › 2017.09–2017.12
RM33C0E _59 Vehicle Exterior _065472 LIGHTING (EXT) _0331112 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  High Beam Headlight Circuit  


DESCRIPTION

The headlight ECU sub-assembly controls the high beam headlights.

WIRING DIAGRAM

E371004E05
0.198,3.333 2.354,3.573 2.156,0.24 10 false Headlight ECU Sub-assembly 0.208,3.198 0.479,3.458 0.271,0.26 10 false B 1.25,1.333 1.521,1.594 0.271,0.26 10 false HI+ 1.25,1.604 1.521,1.865 0.271,0.26 10 false HI- 3,2.948 5.156,3.188 2.156,0.24 10 false Headlight Unit Assembly 4.99,2.396 5.99,2.74 1,0.344 10 false Headlight Unit 4.854,1.906 6.5,2.208 1.646,0.302 10 false Lo/Hi Beam Shade 1.542,1.24 1.813,1.5 0.271,0.26 10 false 10 1.583,1.51 1.854,1.771 0.271,0.26 10 false 1 4.99,2.25 5.26,2.51 0.271,0.26 10 false C 4.385,1.25 4.656,1.51 0.271,0.26 10 false 10 4.427,1.51 4.698,1.771 0.271,0.26 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System)>INITIALIZATION


PROCEDURE

1.CHECK LIGHTS
a.

Check the illumination of each high beam lights.


Result:
Result Proceed to
LH side high beam light does not illuminate A
RH side high beam light does not illuminate B



A

2.PERFORM ACTIVE TEST USING GTS

B

6.PERFORM ACTIVE TEST USING GTS
2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > HL AutoLeveling > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Headlight High Beam High beam headlights OFF or ON -
Body Electrical > HL AutoLeveling > Active Test
Tester Display
Headlight High Beam
50004 361 19
OK:

High beam headlight turn on.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HEADLIGHT UNIT ASSEMBLY LH
3.CHECK HEADLIGHT UNIT ASSEMBLY LH
a.

Interchange the headlight unit assembly LH with RH and connect the connectors.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

4.CHECK OPERATION (HIGH BEAM HEADLIGHT)
4.CHECK OPERATION (HIGH BEAM HEADLIGHT)
a.

Check that the high beam headlight operates normally.

OK:

High beam headlight operates normally.



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

5.INSPECT HEADLIGHT UNIT ASSEMBLY LH
5.INSPECT HEADLIGHT UNIT ASSEMBLY LH
E371562C06
1.833,0.354 2.198,0.656 0.365,0.302 4.896,0.375 5.26,0.677 0.365,0.302 1.354,2.083 1.281,1.385 false 2.521,2.094 2.688,1.396 false 0.615,0.438 0.927,0.635 0.313,0.198 10 false *a 4.115,0.469 4.427,0.667 0.313,0.198 10 false *b 1.969,0.417 2.281,0.615 0.313,0.198 10 false B 5.031,0.458 5.344,0.656 0.313,0.198 10 false C 1.302,2.125 1.979,2.344 0.677,0.219 10 false HI- 2.427,2.125 3.104,2.344 0.677,0.219 10 false HI+
*a Component without harness connected
(to Headlight ECU Sub-assembly LH)
*b Component without harness connected
(to Headlight Unit LH)




c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-10 (HI+) - C-10 Always Below 1 Ω
B-1 (HI-) - C-4 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

6.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling (Sub) / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > HL AutoLeveling (Sub) > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Headlight High Beam High beam headlights OFF or ON -
Body Electrical > HL AutoLeveling (Sub) > Active Test
Tester Display
Headlight High Beam
50004 414 4
OK:

High beam headlight turn on.



Result:
Proceed to
OK
NG



OK

NG

7.CHECK HEADLIGHT UNIT ASSEMBLY RH
7.CHECK HEADLIGHT UNIT ASSEMBLY RH
a.

Interchange the headlight unit assembly RH with LH and connect the connectors.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

8.CHECK OPERATION (HIGH BEAM HEADLIGHT)
8.CHECK OPERATION (HIGH BEAM HEADLIGHT)
a.

Check that the high beam headlight operates normally.

OK:

High beam headlight operates normally.



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

NG

9.INSPECT HEADLIGHT UNIT ASSEMBLY RH
9.INSPECT HEADLIGHT UNIT ASSEMBLY RH
E371562C07
1.833,0.354 2.198,0.656 0.365,0.302 4.896,0.375 5.26,0.677 0.365,0.302 1.354,2.083 1.281,1.385 false 2.521,2.094 2.688,1.396 false 0.615,0.438 0.927,0.635 0.313,0.198 10 false *a 4.115,0.469 4.427,0.667 0.313,0.198 10 false *b 1.969,0.417 2.281,0.615 0.313,0.198 10 false B 5.031,0.458 5.344,0.656 0.313,0.198 10 false C 1.302,2.125 1.979,2.344 0.677,0.219 10 false HI- 2.427,2.125 3.104,2.344 0.677,0.219 10 false HI+
*a Component without harness connected
(to Headlight ECU Sub-assembly RH)
*b Component without harness connected
(to Headlight Unit RH)




c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-10 (HI+) - C-10 Always Below 1 Ω
B-1 (HI-) - C-4 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG