Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System) › 2017.09–2017.12
RM33C0E _59 Vehicle Exterior _065472 LIGHTING (EXT) _0331112 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Headlight Beam Level Control Actuator Circuit  


DESCRIPTION

The headlight ECU sub-assemblies operate the headlight leveling motors according to the vehicle conditions.

WIRING DIAGRAM

E371119E04
0.646,3.385 2.99,3.677 2.344,0.292 10 false Headlight ECU Sub-assembly LH 0.531,7 2.875,7.292 2.344,0.292 10 false Headlight ECU Sub-assembly RH 4.427,2.24 6.771,2.531 2.344,0.292 10 false Headlight Leveling Motor LH 4.406,5.833 6.75,6.125 2.344,0.292 10 false Headlight Leveling Motor RH 3.521,3.073 5.354,3.438 1.833,0.365 10 false Headlight Unit Assembly LH 3.49,6.708 5.354,7.052 1.865,0.344 10 false Headlight Unit Assembly RH 1.823,1.146 2.406,1.406 0.583,0.26 10 false ACTBI 1.833,4.76 2.417,5.021 0.583,0.26 10 false ACTBI 1.823,1.417 2.406,1.677 0.583,0.26 10 false ACTSI 1.833,5.031 2.417,5.292 0.583,0.26 10 false ACTSI 1.823,1.677 2.406,1.938 0.583,0.26 10 false ACTGI 1.833,5.313 2.417,5.573 0.583,0.26 10 false ACTGI 2.375,1.052 2.563,1.25 0.188,0.198 10 false 7 2.375,1.323 2.563,1.521 0.188,0.198 10 false 8 2.344,1.594 2.531,1.792 0.188,0.198 10 false 17 2.385,4.656 2.573,4.854 0.188,0.198 10 false 7 2.385,4.917 2.573,5.115 0.188,0.198 10 false 8 2.354,5.208 2.542,5.406 0.188,0.198 10 false 17 0.646,3.24 0.833,3.438 0.188,0.198 10 false B 0.531,6.854 0.719,7.052 0.188,0.198 10 false B 4.438,2.094 4.625,2.292 0.188,0.198 10 false D 4.417,5.698 4.604,5.896 0.188,0.198 10 false D 4.208,1.063 4.396,1.26 0.188,0.198 10 false 1 4.208,1.323 4.396,1.521 0.188,0.198 10 false 2 4.208,1.583 4.396,1.781 0.188,0.198 10 false 3 4.198,4.677 4.385,4.875 0.188,0.198 10 false 1 4.198,4.948 4.385,5.146 0.188,0.198 10 false 2 4.198,5.208 4.385,5.406 0.188,0.198 10 false 3 1.177,7.469 3.177,7.688 2,0.219 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System)>INITIALIZATION


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > HL AutoLeveling > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Drive The Leveling Motor Headlight leveling motor upward or downward operation Stop, Down or Up Perform the Active Test with the power switch is on (READY) and vehicle stopped
Body Electrical > HL AutoLeveling > Active Test
Tester Display
Drive The Leveling Motor
50004 361 3
OK:

Headlight leveling motors operate normally.



Result:
Result Proceed to
OK A
NG (for LH Side) B
NG (for RH Side) C



A

B

2.CHECK HEADLIGHT UNIT ASSEMBLY LH

C

5.CHECK HEADLIGHT UNIT ASSEMBLY RH
2.CHECK HEADLIGHT UNIT ASSEMBLY LH
a.

Interchange the headlight unit assembly LH with RH and connect the connectors.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

3.CHECK OPERATION (AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM)
3.CHECK OPERATION (AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM)
a.

Check that the headlight leveling motor LH operate normally.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System)>OPERATION CHECK

OK:

Headlight leveling motor LH operate normally.



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

4.INSPECT HEADLIGHT UNIT ASSEMBLY LH
4.INSPECT HEADLIGHT UNIT ASSEMBLY LH
E371566C02
1.802,0.448 2.167,0.698 0.365,0.25 4.885,0.458 5.25,0.708 0.365,0.25 1.552,2.031 2.198,1.396 false 2.885,2.063 2.396,1.385 false 2.208,2.063 2.219,1.573 false 0.729,0.573 1.042,0.771 0.313,0.198 10 false *a 4.031,0.583 4.344,0.781 0.313,0.198 10 false *b 1.948,0.51 2.26,0.708 0.313,0.198 10 false B 5.031,0.51 5.344,0.708 0.313,0.198 10 false D 1.344,2.073 1.917,2.313 0.573,0.24 10 false ACTBI 2.698,2.073 3.271,2.313 0.573,0.24 10 false ACTSI 2.031,2.083 2.604,2.323 0.573,0.24 10 false ACTGI
*a Component without harness connected
(to Headlight ECU Sub-assembly LH)
*b Component without harness connected
(to Headlight Leveling Motor LH)




c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-7 (ACTBI) - D-1 Always Below 1 Ω
B-8 (ACTSI) - D-2 Always Below 1 Ω
B-17 (ACTGI) - D-3 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HEADLIGHT UNIT ASSEMBLY RH
a.

Interchange the headlight unit assembly RH with LH and connect the connectors.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

6.CHECK OPERATION (AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM)
6.CHECK OPERATION (AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM)
a.

Check that the headlight leveling motor RH operate normally.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System)>OPERATION CHECK

OK:

Headlight leveling motor RH operate normally.



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

NG

7.INSPECT HEADLIGHT UNIT ASSEMBLY RH
7.INSPECT HEADLIGHT UNIT ASSEMBLY RH
E371566C02
1.802,0.448 2.167,0.698 0.365,0.25 4.885,0.458 5.25,0.708 0.365,0.25 1.552,2.031 2.198,1.396 false 2.885,2.063 2.396,1.385 false 2.208,2.063 2.219,1.573 false 0.729,0.573 1.042,0.771 0.313,0.198 10 false *a 4.031,0.583 4.344,0.781 0.313,0.198 10 false *b 1.948,0.51 2.26,0.708 0.313,0.198 10 false B 5.031,0.51 5.344,0.708 0.313,0.198 10 false D 1.344,2.073 1.917,2.313 0.573,0.24 10 false ACTBI 2.698,2.073 3.271,2.313 0.573,0.24 10 false ACTSI 2.031,2.083 2.604,2.323 0.573,0.24 10 false ACTGI
*a Component without harness connected
(to Headlight ECU Sub-assembly RH)
*b Component without harness connected
(to Headlight Leveling Motor RH)




c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-7 (ACTBI) - D-1 Always Below 1 Ω
B-8 (ACTSI) - D-2 Always Below 1 Ω
B-17 (ACTGI) - D-3 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG