Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0331295 HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY)  P0ABF00  Hybrid/EV Battery Current Sensor "A" Circuit Range/Performance  


DESCRIPTION

A battery current sensor is installed to the positive (+) terminal side of the HV battery and detects current flowing from the HV battery. The battery current sensor outputs voltage, which changes between 0 and 5 V according to the detected amperage, to the IB terminal of the battery voltage sensor. The battery voltage sensor sends signals to the hybrid vehicle control ECU assembly. The hybrid vehicle control ECU assembly determines the charging and discharging amount of the HV battery based on the received signals and calculates the SOC of the HV battery through the accumulated amperage.

A304993E14
0.052,0.073 0.625,0.521 0.573,0.448 10 false Charging Current 0.719,0.083 1.479,0.552 0.76,0.469 10 false Discharging Current 0.875,1.01 2.563,1.25 1.688,0.24 10 false Battery Current Sensor 2.094,2.677 3.688,2.948 1.594,0.271 10 false Battery Voltage Sensor 2.406,1.26 2.865,1.458 0.458,0.198 10 false VIB 2.438,1.563 2.75,1.76 0.313,0.198 10 false IB 2.406,1.865 2.865,2.063 0.458,0.198 10 false GIB 3.177,0.104 6,0.323 2.823,0.219 10 false Battery Current Sensor Output Voltage 3.969,0.469 4.427,0.667 0.458,0.198 10 false (V) 3.958,0.865 4.417,1.063 0.458,0.198 10 false 4.5 3.969,1.594 4.427,1.792 0.458,0.198 10 false 2.5 3.969,2.323 4.427,2.521 0.458,0.198 10 false 0.5 4.25,2.625 4.865,2.823 0.615,0.198 10 false -200 5.594,2.625 5.75,2.823 0.156,0.198 10 false 0 6.729,2.625 7.063,2.823 0.333,0.198 10 false 200 4.229,3.083 4.865,3.271 0.635,0.188 10 false Charge 6.49,3.083 7.146,3.302 0.656,0.219 10 false Discharge 4.948,3.198 6.25,3.427 1.302,0.229 10 false HV Battery Current 6.188,3.188 6.531,3.417 0.344,0.229 10 false (A)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0ABF00 Hybrid/EV Battery Current Sensor "A" Circuit Range/Performance Abnormal battery current sensor characteristics:
(based on hybrid system consumption and HV battery output).
(1 trip detection logic)
·

HV battery junction block assembly

·

Battery voltage sensor

·

Hybrid battery thermistor (wire harness or connector)


Comes on Master Warning Light:
Comes on

Related Data List
DTC No. Data List
P0ABF00 -

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Drive the vehicle for approximately 10 minutes according to the freeze frame data items "Vehicle Speed", "Accelerator Position", "Hybrid Battery Current", "Motor Torque" and "Generator Torque".

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
One of the following applies:
·

Only P0ABF00 is output.

·

One or more DTCs other than P0AFC00 and P0AFC96 are also output.


A
P0AFC00 or P0AFC96 is also output. B


e.

Turn the power switch off.



A

2.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - HV BATTERY JUNCTION BLOCK ASSEMBLY)

B

2.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - HV BATTERY JUNCTION BLOCK ASSEMBLY)

OK

3.REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

NG

3.REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

NEXT

4.CLEAR DTC
5.PERFORM ROAD TEST
a.

Drive the vehicle for approximately 10 minutes according to the freeze frame data items "Vehicle Speed", "Accelerator Position", "Hybrid Battery Current", "Motor Torque" and "Generator Torque".

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT (HYBRID CONTROL)
6.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P0ABF00 is not output. A
P0ABF00 is output again. B



e.

Turn the power switch off.



A

COMPLETED

B