Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0331295 HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY)  P0A9B11  Hybrid/EV Battery Temperature Sensor "A" Circuit Short to Ground  P0A9B15  Hybrid/EV Battery Temperature Sensor "A" Circuit Short to Auxiliary Battery or Open  P0AC511  Hybrid/EV Battery Temperature Sensor "B" Circuit Short to Ground  P0AC515  Hybrid/EV Battery Temperature Sensor "B" Circuit Short to Auxiliary Battery or Open  P0ACA11  Hybrid/EV Battery Temperature Sensor "C" Circuit Short to Ground  P0ACA15  Hybrid/EV Battery Temperature Sensor "C" Circuit Short to Auxiliary Battery or Open  


DESCRIPTION

The battery temperature sensors are provided at 3 locations of the HV battery. The resistance of the thermistor, which is built into each battery temperature sensor, varies in accordance with changes in the HV battery temperature. The lower the battery temperature, the higher the thermistor resistance. Conversely, the higher the temperature, the lower the resistance. The battery voltage sensor uses the battery temperature sensors to detect the HV battery temperature, and sends the detected value to the hybrid vehicle control ECU assembly. Based on the results of this detection, the hybrid vehicle control ECU assembly controls the blower fan. (The blower fan starts when the HV battery temperature rises above a predetermined level.)

Temperature Sensor Identification Cross Reference Table:
DTC Title Sensor Battery Temperature Sensor GTS Display
A 0 1
B 1 2
C 2 3


HINT:

Use the reference table above to determine which battery temperature sensor each DTC corresponds to. For example, sensor A in the DTC title column is battery temperature sensor 0. This sensor is displayed as Hybrid Battery Temperature 1 in the Data List.


A171806E05
1.896,0.031 2.635,0.188 0.74,0.156 10 false Reference: 2.167,0.354 2.427,0.5 0.26,0.146 10 false 250 2.167,0.677 2.427,0.823 0.26,0.146 10 false 200 2.167,0.979 2.427,1.125 0.26,0.146 10 false 150 2.177,1.271 2.438,1.417 0.26,0.146 10 false 100 2.25,1.583 2.438,1.729 0.188,0.146 10 false 50 2.333,1.896 2.438,2.042 0.104,0.146 10 false 0 3.271,2.25 3.375,2.396 0.104,0.146 10 false 0 2.573,2.25 2.802,2.417 0.229,0.167 10 false -40 2.917,2.25 3.146,2.417 0.229,0.167 10 false -20 3.521,2.25 3.698,2.417 0.177,0.167 10 false 20 3.813,2.25 3.99,2.417 0.177,0.167 10 false 40 4.094,2.25 4.271,2.417 0.177,0.167 10 false 60 4.396,2.25 4.573,2.417 0.177,0.167 10 false 80 4.646,2.25 4.906,2.417 0.26,0.167 10 false 100 3.177,2.458 3.448,2.604 0.271,0.146 10 false (32) 2.531,2.448 2.865,2.615 0.333,0.167 10 false (-40) 2.906,2.448 3.167,2.615 0.26,0.167 10 false (-4) 3.458,2.448 3.729,2.615 0.271,0.167 10 false (68) 3.708,2.448 4.073,2.615 0.365,0.167 10 false (104) 4.031,2.448 4.375,2.615 0.344,0.167 10 false (140) 4.354,2.448 4.708,2.615 0.354,0.167 10 false (176) 4.677,2.448 5.021,2.615 0.344,0.167 10 false (212) 5.094,2.24 5.365,2.438 0.271,0.198 10 false (°C) 5.094,2.448 5.427,2.646 0.333,0.198 10 false (°F) 1.823,0.375 2.115,0.573 0.292,0.198 10 false (kΩ) 1.24,1.146 1.969,1.333 0.729,0.188 10 false Resistance 5.531,2.24 6.875,2.427 1.344,0.188 10 false Battery Temperature 2.604,0.042 5.698,0.219 3.094,0.177 10 false Battery Temperature Sensor Characteristic Graph

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A9B11 Hybrid/EV Battery Temperature Sensor "A" Circuit Short to Ground The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic)
·

Battery voltage sensor

·

Hybrid battery thermistor (battery temperature sensor)

·

Wire harness or connector


Comes on Master Warning Light:
Comes on
P0A9B15 Hybrid/EV Battery Temperature Sensor "A" Circuit Short to Auxiliary Battery or Open The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic)
·

Battery voltage sensor

·

Hybrid battery thermistor (battery temperature sensor)

·

Wire harness or connector


Comes on Master Warning Light:
Comes on
P0AC511 Hybrid/EV Battery Temperature Sensor "B" Circuit Short to Ground The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic)
·

Battery voltage sensor

·

Hybrid battery thermistor (battery temperature sensor)

·

Wire harness or connector


Comes on Master Warning Light:
Comes on
P0AC515 Hybrid/EV Battery Temperature Sensor "B" Circuit Short to Auxiliary Battery or Open The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic)
·

Battery voltage sensor

·

Hybrid battery thermistor (battery temperature sensor)

·

Wire harness or connector


Comes on Master Warning Light:
Comes on
P0ACA11 Hybrid/EV Battery Temperature Sensor "C" Circuit Short to Ground The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic)
·

Battery voltage sensor

·

Hybrid battery thermistor (battery temperature sensor)

·

Wire harness or connector


Comes on Master Warning Light:
Comes on
P0ACA15 Hybrid/EV Battery Temperature Sensor "C" Circuit Short to Auxiliary Battery or Open The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic)
·

Battery voltage sensor

·

Hybrid battery thermistor (battery temperature sensor)

·

Wire harness or connector


Comes on Master Warning Light:
Comes on

Related Data List
DTC No. Data List
P0A9B11 Hybrid Battery Temperature 1 to 3
P0A9B15
P0AC511
P0AC515
P0ACA11
P0ACA15

HINT:
·

After checking for the above DTCs, check the hybrid system Data List item "Hybrid Battery Temperature" using the GTS.

Temperature Displayed Malfunction
Below -45°C (-49°F) Open or +B short circuit
95°C (203°F) or more GND short circuit

·

If the vehicle as is left as is for 24 hours, the value of "Hybrid Battery Temperature" will be almost the same as the ambient temperature.



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 5 seconds or more.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
"P0AFC00, P0AFC96 or P308A12" is not output. A
"P0AFC00, P0AFC96 or P308A12" is also output. B


e.

Turn the power switch off.



A

2.READ VALUE USING GTS (HYBRID BATTERY TEMPERATURE)

B

2.READ VALUE USING GTS (HYBRID BATTERY TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Temperature 1 to 3.


d.

Read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Reference Value Diagnostic Note
Hybrid Battery Temperature 1 HV battery temperature sensor output. -50 to 205.9°C (-58 to 402.6°F) Same as ambient temperature (left as is for 24 hours)
·

Battery temperature sensor

·

Battery voltage sensor


Hybrid Battery Temperature 2 HV battery temperature sensor output. -50 to 205.9°C (-58 to 402.6°F) Same as ambient temperature (left as is for 24 hours)
·

Battery temperature sensor

·

Battery voltage sensor


Hybrid Battery Temperature 3 HV battery temperature sensor output. -50 to 205.9°C (-58 to 402.6°F) Same as ambient temperature (left as is for 24 hours)
·

Battery temperature sensor

·

Battery voltage sensor


Powertrain > Hybrid Control > Data List
Tester Display
Hybrid Battery Temperature 1
Hybrid Battery Temperature 2
Hybrid Battery Temperature 3
50003 397 198,199,200

HINT:

A malfunctioning sensor (battery temperature sensor 0, 1 or 2) can be determined by comparing the output temperature of the 3 battery temperature sensors.


e.

Turn the power switch off.


Result:
Proceed to
NEXT



NEXT

3.CHECK CONNECTOR CONNECTION CONDITION (BATTERY VOLTAGE SENSOR CONNECTION CONDITION)
3.CHECK CONNECTOR CONNECTION CONDITION (BATTERY VOLTAGE SENSOR CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A408933N01
1.594,0.74 2.031,1.042 0.438,0.302 1.635,0.771 2,1 0.365,0.229 10 true z17

Check the connections of the z17 battery voltage sensor connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

The connector is connected securely and there are no contact problems.


Result:
Proceed to
OK
NG



d.

Install the No. 1 hybrid battery exhaust duct.



OK

4.CHECK HYBRID BATTERY THERMISTOR (BATTERY TEMPERATURE SENSOR)

NG

CONNECT SECURELY

4.CHECK HYBRID BATTERY THERMISTOR (BATTERY TEMPERATURE SENSOR)

OK

NG

5.CHECK HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR)
5.CHECK HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper HV battery cover sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL


c.

Check the wire harness and connectors of the battery temperature sensors for abnormalities by sight and touch.

Specified Condition:

There are no open or short circuits in the wire harness and connectors. There are no short circuits to other wire harnesses.



d.

Install the upper HV battery cover sub-assembly.


Result:
Proceed to
OK
NG



OK

NG

REPAIR HARNESS OR CONNECTOR (BATTERY TEMPERATURE SENSOR)