Refer to the description for DTC P0C7396.
The inverter water pump assembly sends the inverter water pump speed (measured value) signal to the hybrid vehicle control ECU assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P314A31 | Motor Electronics Coolant Pump "A" No Signal | The inverter water pump speed signal is not sent to the hybrid vehicle control ECU assembly when the power switch is turned on (READY).*
(1 trip detection logic) |
·
Wire harness or connector ·
Hybrid vehicle control ECU assembly ·
Inverter water pump assembly ·
INV W/PMP fuse ·
IGCT relay ·
IGCT fuse |
Comes on | Master Warning Light:
Comes on |
A malfunction (open, short to +B or short to ground) in the speed signal line from the inverter water pump assembly to the hybrid vehicle control ECU assembly is detected.
A malfunction in the +B line is detected.
A malfunction in the inverter water pump assembly power source circuit is detected.
A malfunction in hybrid vehicle control ECU assembly power source circuit is detected.
| DTC No. | Data List |
|---|---|
| P314A31 | ·
Inverter Water Pump Revolution ·
Inverter Water Pump Duty Ratio ·
Ready Signal |
| DTC No. | Active Test |
|---|---|
| P314A31 | Activate the Inverter Water Pump |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
Turn the power switch on (READY) and wait for 2 minutes or more.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
Refer to the wiring diagram for DTC P0C7396.
| Proceed to |
|---|
| NEXT |
NEXT
Make sure that the HV coolant level is above the low line of the inverter reserve tank.
Be sure to perform the inspection with the auxiliary battery voltage at 12 V or more.
When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.
When the inverter water pump assembly signal line (SWP - IWP) is open or its connection is faulty, the inverter water pump assembly is operated forcibly.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Inverter Water Pump.
| Tester Display |
|---|
| Activate the Inverter Water Pump |
Perform the "Activate the Inverter Water Pump" Active Test.
Touch the inverter water pump assembly and check that it is operating (vibrating).
The inverter water pump is operating (vibrating).
Perform the Active Test with the inverter coolant temperature between -15 and 65°C (5 to 149°F).
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A28 hybrid vehicle control ECU assembly connector.
Disconnect the w1 inverter water pump assembly connector.
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU assembly) |
| *b | Front view of wire harness connector
(to Inverter Water Pump Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A28-14 (NIWP) - w1-2 (NWP) | Power switch off | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A28-14 (NIWP) or w1-2 (NWP) -Body ground and other terminals | Power switch off | 10 kΩ or higher |
Check the condition (looseness, deterioration, etc.) of the wire to body ground for the inverter water pump assembly.
Reconnect the w1 inverter water pump assembly connector.
Reconnect the A28 hybrid vehicle control ECU assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the w1 inverter water pump assembly connector.
Turn the power switch on (IG).
| *a | Component with harness connected
(Hybrid Vehicle Control ECU Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A28-14 (NIWP) - K69-6 (E1) | Power switch on (IG) | 11 to 14 V |
Turn the power switch off.
Reconnect the w1 inverter water pump assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| NEXT |
NEXT
Be sure to perform the inspection with the auxiliary battery voltage at 12 V or more.
When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Inverter Water Pump.
| Tester Display |
|---|
| Activate the Inverter Water Pump |
Perform the "Activate the Inverter Water Pump" Active Test.
| *a | Component with harness connected
(Hybrid Vehicle Control ECU Assembly) |
Connect an oscilloscope between the hybrid vehicle control ECU assembly terminals specified in the table below, and measure the waveform.
| Item | Content |
|---|---|
| Terminal | A28-14 (NIWP) - K69-6 (E1) |
| Equipment Setting | 5 V/DIV., 5 ms./DIV. |
| Condition | Power switch on (IG), during Active Test |
The period of the wavelength is 13 msec or less.
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the IGCT relay from the No. 6 relay block.
Disconnect the w1 inverter water pump assembly connector.
Measure the resistance according to the value(s) in the table below.
| *A | for LHD | *B | for RHD |
| *1 | No. 6 Relay Block | *2 | IGCT Relay |
| *a | Front view of wire harness connector
(to Inverter Water Pump Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| w1-4 (+BWP) - 5 (IGCT relay) | Power switch off | Below 1 Ω |
Do not apply excessive force when using the probes of the tester to perform the inspection. If excessive force is used, the terminals will be damaged.
| *a | Example |
| *b | Shake Slightly |
| *c | Vibrate Slightly |
Connectors
Slightly shake the connector vertically and horizontally.
Wire Harness
Slightly shake the wire harness vertically and horizontally.
The connector joint and fulcrum of the vibration are the major areas that should be checked thoroughly.
No. 6 Relay Block
Apply slight vibration with a finger to the No. 6 relay block and check whether a malfunction occurs.
INV W/PMP fuse
Apply slight vibration with a finger to the INV W/PMP fuse and check whether a malfunction occurs.
IGCT relay
Apply slight vibration with a finger to the IGCT relay and check whether a malfunction occurs.
Reconnect the w1 inverter water pump assembly connector.
Install the IGCT relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the w1 inverter water pump assembly connector.
| *a | Front view of wire harness connector
(to Inverter Water Pump Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| w1-1 (GND) - Body ground | Power switch off | Below 1 Ω |
Reconnect the w1 inverter water pump assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>WATER PUMP WITH MOTOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
After replacing the inverter water pump assembly, add HV coolant and perform air bleeding.
Click hereGeneral>MAINTENANCE>COOLANT(for Inverter)>REPLACEMENT
| Proceed to |
|---|
| NEXT |
NEXT
| *1 | No. 4 Relay Block |
| *2 | INV W/PMP Fuse |
Remove the INV W/PMP fuse from the No. 4 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| INV W/PMP fuse | Always | Below 1 Ω |
Install the INV W/PMP fuse.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check installation condition of the INV W/PMP fuse.
INV W/PMP fuse is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the INV W/PMP fuse from No. 4 relay block.
Remove the IGCT relay from the No. 6 relay block.
Disconnect the w1 inverter water pump assembly connector.
Measure the resistance according to the value(s) in the table below.
| *A | for LHD | *B | for RHD |
| *1 | No. 6 Relay Block | *2 | IGCT Relay |
| *3 | No. 4 Relay Block | *4 | INV W/PMP Fuse |
| *a | Front view of wire harness connector
(to Inverter Water Pump Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (INV W/PMP fuse) - w1-4 (+BWP) | Power switch off | Below 1 Ω |
| 1 (INV W/PMP fuse) - 5 (IGCT relay) | Power switch off | Below 1 Ω |
| 2 (INV W/PMP fuse) or w1-4 (+BWP) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
Do not apply excessive force when using the probes of the tester to perform the inspection. If excessive force is used, the terminals will be damaged.
Reconnect the w1 inverter water pump assembly connector.
Install the IGCT relay.
Install the INV W/PMP fuse.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 4 Relay Block |
| *2 | INV W/PMP Fuse |
Remove the INV W/PMP fuse from the No. 4 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| INV W/PMP fuse | Always | Below 1 Ω |
Install the INV W/PMP fuse.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the inverter water pump assembly connector securely.
| Proceed to |
|---|
| NEXT |
NEXT
Check the terminals of the INV W/PMP fuse holder.
The terminals of the INV W/PMP fuse holder are not bent, loose or corroded.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 4 Relay Block |
| *2 | INV W/PMP Fuse |
Remove the INV W/PMP fuse from the No. 4 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| INV W/PMP fuse | Always | Below 1 Ω |
Install the INV W/PMP fuse.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 4 Relay Block |
| *2 | INV W/PMP Fuse |
Remove the INV W/PMP fuse from the No. 4 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| INV W/PMP fuse | Always | Below 1 Ω |
Install the INV W/PMP fuse.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the w1 inverter water pump assembly connector.
| *a | Front view of wire harness connector
(to Inverter Water Pump Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| w1-1 (GND) - Body ground | Power switch off | Below 1 Ω |
Reconnect the w1 inverter water pump assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the terminals of the INV W/PMP fuse holder.
The terminals of the INV W/PMP fuse holder are not bent, loose or corroded.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>WATER PUMP WITH MOTOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
After replacing the inverter water pump with motor assembly, add HV coolant and perform air bleeding.
Click hereGeneral>MAINTENANCE>COOLANT(for Inverter)>REPLACEMENT
| Proceed to |
|---|
| NEXT |
NEXT
| *1 | No. 4 relay block |
| *2 | INV W/PMP Fuse |
Remove the INV W/PMP fuse from the No. 4 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| INV W/PMP fuse | Always | Below 1 Ω |
Install the INV W/PMP fuse.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the terminals of the INV W/PMP fuse holder.
| Proceed to |
|---|
| NEXT |
NEXT