Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0331295 HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY) J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY)  Pattern Select Switch Sport Mode Circuit  


DESCRIPTION

When selecting SPORT mode, the switch operation signal is sent to the hybrid vehicle control ECU assembly. Following this, the system enters SPORT mode and the vehicle will be driven using SPORT mode. This signal is then transmitted from the hybrid vehicle control ECU assembly via CAN to the combination meter assembly to illuminate the SPORT mode indicator.

WIRING DIAGRAM

A378433E12
3.677,1.125 4.104,1.406 0.427,0.281 10 false ECM 0.917,1.115 2.781,1.427 1.865,0.313 10 false Combination Meter Assembly 1.604,3.792 4.427,4.188 2.823,0.396 10 false SPORT Mode Switch (Electric Parking Brake Switch Assembly) 0.906,4.323 2.771,4.635 1.865,0.313 10 false : CAN Communication Line 5.188,3.792 6.594,4.292 1.406,0.5 10 false Hybrid Vehicle Control ECU Assembly 5.073,3.125 5.385,3.323 0.313,0.198 10 false K69 5.083,2.344 5.396,2.542 0.313,0.198 10 false K70 5.115,2.927 5.531,3.177 0.417,0.25 10 false 10 5.146,2.156 5.458,2.323 0.313,0.167 10 false 6 4.219,2 4.594,2.167 0.375,0.167 10 false 12*1 4.219,2.771 4.615,2.938 0.396,0.167 10 false 13*1 3.99,2.219 4.302,2.385 0.313,0.167 10 false P 3.979,2.99 4.292,3.156 0.313,0.167 10 false B 1.604,3.635 1.917,3.833 0.313,0.198 10 false K37 1.813,3 2.281,3.25 0.469,0.25 10 false GND1 0.063,3.458 0.865,3.688 0.802,0.229 10 false *1: for LHD 2.531,2.771 4.146,3 1.615,0.229 10 false NORMAL 2.552,2.052 3.594,2.271 1.042,0.219 10 false SPORT 5.427,2.344 5.979,2.542 0.552,0.198 10 false SPRT 5.458,3.104 6.01,3.302 0.552,0.198 10 false NORM 4.219,2.198 4.594,2.365 0.375,0.167 10 false 13*2 4.219,2.958 4.615,3.125 0.396,0.167 10 false 12*2 1.479,2.969 1.927,3.146 0.448,0.177 10 false 9*2 1.406,2.781 1.854,2.958 0.448,0.177 10 false 16*1 0.063,3.75 0.865,3.979 0.802,0.229 10 false *2: for RHD

PROCEDURE

1.READ VALUE USING GTS (CAN BUS CHECK)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>Pattern Select Switch EV Mode Circuit

Result:
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed B



A

2.CHECK DTC OUTPUT (HEALTH CHECK)

B

2.CHECK DTC OUTPUT (HEALTH CHECK)

A

3.READ VALUE USING GTS (SPORT MODE SWITCH, NORMAL MODE SWITCH)

B

GO TO DTC CHART

3.READ VALUE USING GTS (SPORT MODE SWITCH, NORMAL MODE SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Sport Mode Switch, Normal Mode Switch.

Powertrain > Hybrid Control > Data List
Tester Display
Sport Mode Switch
Normal Mode Switch
50003 397 508,509

d.

Read the value displayed on the GTS.

Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition
Sport Mode Switch SPORT mode switch condition ON or OFF SPORT mode switch being pushed and held:
ON
SPORT mode switch not operated:
OFF
Normal Mode Switch NORMAL mode switch condition ON or OFF NORMAL mode switch being pushed and held:
ON
NORMAL mode switch not operated:
OFF
Result:
Result Proceed to
The GTS display changes according to the electric parking brake switch assembly operation. A
The GTS display does not change according to the electric parking brake switch assembly operation. B



e.

Turn the power switch off.



A

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

B

4.INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY (SPORT MODE, NORMAL MODE)
4.INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY (SPORT MODE, NORMAL MODE)

OK

5.CHECK HARNESS AND CONNECTOR (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY - BODY GROUND)

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the K37 electric parking brake switch assembly connector.


b.
A406713C06
0.292,0.917 0.719,1.208 0.427,0.292 2.771,1.625 2.396,1.292 true 0.844,1.656 1.156,1.302 true 0.385,0.99 0.844,1.188 0.458,0.198 10 false K37 2.646,1.677 3.208,1.99 0.563,0.313 10 false GND1*A 0.25,0.24 0.563,0.396 0.313,0.156 10 false *a 0.469,1.688 1.083,1.938 0.615,0.25 10 false GND1*B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Electric Parking Brake Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
K37-16 (GND1) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
K37-9 (GND1) - Body ground Always Below 1 Ω



c.

Reconnect the K37 electric parking brake switch assembly connector.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
a.

Disconnect the K69 and K70 hybrid vehicle control ECU assembly connectors.


b.

Disconnect the K37 electric parking brake switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

A406715C03
1.948,0.104 2.385,0.354 0.438,0.25 2.479,0.104 2.917,0.354 0.438,0.25 4.167,1.281 4.604,1.531 0.438,0.25 1.792,2.25 2.219,1.792 true 3.302,2.26 2.698,1.729 true 5.594,2.146 5.417,1.583 true 5.083,2.125 5.281,1.594 true 2.063,0.167 2.521,0.365 0.458,0.198 10 false K69 2.583,0.156 3.042,0.354 0.458,0.198 10 false K70 4.271,1.333 4.729,1.531 0.458,0.198 10 false K37 0.354,0.323 0.667,0.479 0.313,0.156 10 false *a 4.323,0.646 4.635,0.802 0.313,0.156 10 false *b 1.542,2.313 2.156,2.51 0.615,0.198 10 false NORM 5.563,2.198 5.885,2.396 0.323,0.198 10 false B*A 3.135,2.313 3.75,2.51 0.615,0.198 10 false SPRT 5.031,2.198 5.365,2.406 0.333,0.208 10 false P*A 5.031,2.365 5.365,2.573 0.333,0.208 10 false B*B 5.573,2.375 5.896,2.573 0.323,0.198 10 false P*B
*A for LHD *B for RHD
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)
*b Front view of wire harness connector
(to Electric Parking Brake Switch Assembly)


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
K70-6 (SPRT) - K37-12 (P) Always Below 1 Ω
K70-6 (SPRT) or K37-12 (P) - Body ground Always 10 kΩ or higher
K69-10 (NORM) - K37-13 (B) Always Below 1 Ω
K69-10 (NORM) or K37-13 (B) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
K70-6 (SPRT) - K37-13 (P) Always Below 1 Ω
K70-6 (SPRT) or K37-13 (P) - Body ground Always 10 kΩ or higher
K69-10 (NORM) - K37-12 (B) Always Below 1 Ω
K69-10 (NORM) or K37-12 (B) - Body ground Always 10 kΩ or higher



d.

Reconnect the K37 electric parking brake switch assembly.


e.

Reconnect the K69 and K70 hybrid vehicle control ECU assembly connectors.


Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR