Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY) › 2017.09–2020.08
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0331295 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Transmission Control Switch Circuit  


DESCRIPTION

When the shift lever is in S, different ranges can be chosen using the floor shift sequential gate.

WIRING DIAGRAM

Refer to the wiring diagram for the shift paddle switch circuit. (w/ Shift paddle switch)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>Shift Paddle Switch Circuit

A409119E02
2.01,3.427 2.469,3.625 0.458,0.198 10 false K29 2,3.604 4.146,4.208 2.146,0.604 10 false Transmission Control Switch (Shift Lock Control Unit Assembly) 1.99,2.01 2.448,2.208 0.458,0.198 10 false 2 2.24,2.01 2.698,2.208 0.458,0.198 10 false E 2.24,1.333 2.698,1.531 0.458,0.198 10 false IG 2.01,1.344 2.469,1.542 0.458,0.198 10 false 4 0.26,1.427 1.198,2.031 0.938,0.604 10 false from ECU-ACC Fuse 2.563,0.344 3.49,0.781 0.927,0.438 10 false to Spiral Cable Sub-assembly 3.51,1.344 3.969,1.542 0.458,0.198 10 false S 3.771,1.344 4.229,1.542 0.458,0.198 10 false 5 3.781,1.854 4.24,2.052 0.458,0.198 10 false 3*2 3.292,2 3.75,2.198 0.458,0.198 10 false SFTU 3.292,2.677 3.75,2.875 0.458,0.198 10 false SFTD 3.781,2.5 4.24,2.698 0.458,0.198 10 false 1*2 5.292,2.698 5.75,2.896 0.458,0.198 10 false 8 5.26,2.031 5.719,2.229 0.458,0.198 10 false 9 5.26,1.333 5.719,1.531 0.458,0.198 10 false 1 5.521,1.438 5.979,1.635 0.458,0.198 10 false M 5.51,2.115 5.969,2.313 0.458,0.198 10 false SFTU 5.51,2.781 6.031,3.021 0.521,0.24 10 false SFTD 4.99,3.813 5.448,4.01 0.458,0.198 10 false K70 5,3.979 6.719,4.542 1.719,0.563 10 false Hybrid Vehicle Control ECU Assembly 4.25,0.927 4.708,1.125 0.458,0.198 10 false *1 4.688,0.917 5.146,1.115 0.458,0.198 10 false *1 0.167,4.156 2.135,4.354 1.969,0.198 10 false *2: for LHD 0.156,4.458 2.125,4.656 1.969,0.198 10 false *3: for RHD 0.167,3.844 2.135,4.042 1.969,0.198 10 false *1: w/ Shift Paddle Switch 3.781,2.031 4.24,2.229 0.458,0.198 10 false 1*3 3.792,2.688 4.25,2.885 0.458,0.198 10 false 3*3

PROCEDURE

1.READ VALUE USING GTS (SPORTS SHIFT POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Sports Shift Position.

Powertrain > Hybrid Control > Data List
Tester Display
Sports Shift Position
50003 397 233

d.

Read the value displayed on the GTS.

Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition
Sports Shift Position Sports shift position 0 to 255 Shift lever in S, "+" or "-": 1 to 6
Shift lever in any position other than S, "+" and "-": 255
Result:
Result Proceed to
The GTS display changes according to the shift lever operation A
The GTS display does not change according to the shift lever operation B



e.

Turn the power switch off.



A

2.READ VALUE USING GTS (SPORTS SHIFT UP SIGNAL, SPORTS SHIFT DOWN SIGNAL)

B

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
2.READ VALUE USING GTS (SPORTS SHIFT UP SIGNAL, SPORTS SHIFT DOWN SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Sports Shift UP Signal, Sports Shift DOWN Signal.

Powertrain > Hybrid Control > Data List
Tester Display
Sports Shift UP Signal
Sports Shift DOWN Signal
50003 397 83,82

d.

Read the value displayed on the GTS.

Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition
Sports Shift UP Signal Operation of "+" transmission control switch. ON or OFF Shift lever held in "+" operated: ON
Shift lever in S: OFF
Sports Shift DOWN Signal Operation of "-" transmission control switch. ON or OFF Shift lever held in "-" operated: ON
Shift lever in S: OFF
Result:
Result Proceed to
The GTS display changes according to the transmission control switch (shift lock control unit assembly) operation A
The GTS display does not change according to the transmission control switch (shift lock control unit assembly) operation B



e.

Turn the power switch off.



A

3.CHECK FOR INTERMITTENT PROBLEMS

B

7.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)
3.CHECK FOR INTERMITTENT PROBLEMS

OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the K29 transmission control switch (shift lock control unit assembly) connector.


b.

Turn the power switch on (IG).


c.
C251979C75
0.781,1.073 1.125,1.281 0.344,0.208 1.188,1.708 1.604,1.292 true 2.24,1.708 1.854,1.292 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 0.844,1.104 1.156,1.26 0.313,0.156 10 false K29 1.083,1.677 1.396,1.833 0.313,0.156 10 false E 2.292,1.646 2.604,1.802 0.313,0.156 10 false IG
*a Front view of wire harness connector
(to Transmission Control Switch (Shift Lock Control Unit Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K29-4 (IG) - Body ground Power switch on (IG) 11 to 14 V



d.

Turn the power switch off.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K29-4 (IG) - Body ground Power switch off Below 1 V



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K29-2 (E) - Body ground Power switch off Below 1 Ω



g.

Reconnect the K29 transmission control switch (shift lock control unit assembly) connector.


Result:
Proceed to
OK
NG



OK

5.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)

NG

CHECK POWER SOURCE CIRCUIT

5.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.

Disconnect the K29 transmission control switch (shift lock control unit assembly) connector.


b.
C251980C89
1.552,0.458 1.865,0.656 0.313,0.198 0.844,1.583 1.302,1.271 true 1.135,1.708 1.51,1.271 true 1.781,1.729 1.719,1.271 true 2.406,1.729 1.938,1.281 true 2.708,1.604 2.156,1.271 true 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a 1.604,0.479 1.917,0.635 0.313,0.156 10 false K29 0.729,1.552 1.042,1.708 0.313,0.156 10 false S 0.979,1.667 1.281,1.854 0.302,0.188 10 false IG 2.75,1.74 3.417,1.927 0.667,0.188 10 false SFTU*B 2.448,1.667 2.646,1.875 0.198,0.208 10 false E 2.75,1.552 3.365,1.771 0.615,0.219 10 false SFTD*A 1.615,1.958 2.281,2.146 0.667,0.188 10 false SFTD*B 1.625,1.76 2.292,1.948 0.667,0.188 10 false SFTU*A
*A for LHD
*B for RHD
*a Component without harness connected
(Transmission Control Switch (Shift Lock Control Unit Assembly))


Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
K29-4 (IG) - K29-5 (S) Shift lever in S
Shift lever held in "+" or "-"
Below 13 Ω
K29-4 (IG) - K29-5 (S) Shift lever in any position except S 10 kΩ or higher
K29-3 (SFTU) - K29-2 (E) Shift lever held in "+" Below 13 Ω
K29-3 (SFTU) - K29-2 (E) Shift lever in S 10 kΩ or higher
K29-1 (SFTD) - K29-2 (E) Shift lever held in "-" Below 13 Ω
K29-1 (SFTD) - K29-2 (E) Shift lever in S 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
K29-4 (IG) - K29-5 (S) Shift lever in S
Shift lever held in "+" or "-"
Below 13 Ω
K29-4 (IG) - K29-5 (S) Shift lever in any position except S 10 kΩ or higher
K29-1 (SFTU) - K29-2 (E) Shift lever held in "+" Below 13 Ω
K29-1 (SFTU) - K29-2 (E) Shift lever in S 10 kΩ or higher
K29-3 (SFTD) - K29-2 (E) Shift lever held in "-" Below 13 Ω
K29-3 (SFTD) - K29-2 (E) Shift lever in S 10 kΩ or higher



c.

Reconnect the K29 transmission control switch (shift lock control unit assembly) connector.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY))

NG

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY))
a.
C264019C59
2.406,2.583 2.823,2.813 0.417,0.229 2.271,2.281 2.75,1.917 true 2.99,2.229 2.792,1.917 true 2.063,2 2.781,1.833 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 2.01,2.323 2.438,2.521 0.427,0.198 10 false SFTU 2.875,2.26 3.302,2.458 0.427,0.198 10 false SFTD 2.49,2.615 2.917,2.813 0.427,0.198 10 false K70 1.917,1.927 2.344,2.125 0.427,0.198 10 false M
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)


Disconnect the K70 hybrid vehicle control ECU assembly connector.


b.

Disconnect the K22 spiral cable sub-assembly connector. (w/ Shift paddle switch)


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

Standard Voltage:
Tester Connection Condition Specified Condition
K70-1 (M) - Body ground Power switch on (IG)
Shift lever in S, "+" or "-"
11 to 14 V
Power switch on (IG)
Except shift lever in S, "+" and "-"
Below 1 V


NOTICE:

If the power switch is turned on (IG) with the hybrid vehicle control ECU assembly connector disconnected, other DTCs will be stored. After performing the inspection, clear the DTCs.



e.

Turn the power switch off.


f.

Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard Resistance:
Tester Connection Condition Specified Condition
K70-9 (SFTU) - Body ground Shift lever held in "+" Below 13 Ω
K70-9 (SFTU) - Body ground Shift lever in S 10 kΩ or higher
K70-8 (SFTD) - Body ground Shift lever held in "-" Below 13 Ω
K70-8 (SFTD) - Body ground Shift lever in S 10 kΩ or higher



g.

Reconnect the K22 spiral cable sub-assembly connector. (w/ Shift paddle switch)


h.

Reconnect the K70 hybrid vehicle control ECU assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.

Disconnect the K29 transmission control switch (shift lock control unit assembly) connector.


b.
C251980C90
1.542,0.458 1.896,0.677 0.354,0.219 1.781,1.719 1.719,1.281 true 2.323,1.698 1.917,1.281 true 2.635,1.531 2.135,1.281 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 1.594,0.479 1.906,0.635 0.313,0.156 10 false K29 1.563,1.74 2.188,1.948 0.625,0.208 10 false SFTU*A 2.375,1.656 2.813,1.844 0.438,0.188 10 false E 2.698,1.667 3.333,1.854 0.635,0.188 10 false SFTU*B 1.563,1.917 2.188,2.125 0.625,0.208 10 false SFTD*B 2.688,1.479 3.323,1.667 0.635,0.188 10 false SFTD*A
*A for LHD
*B for RHD
*a Component without harness connected
(to Transmission Control Switch (Shift Lock Control Unit Assembly))


Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
K29-3 (SFTU) - K29-2 (E) Shift lever held in "+" Below 13 Ω
K29-3 (SFTU) - K29-2 (E) Shift lever in S 10 kΩ or higher
K29-1 (SFTD) - K29-2 (E) Shift lever held in "-" Below 13 Ω
K29-1 (SFTD) - K29-2 (E) Shift lever in S 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
K29-1 (SFTU) - K29-2 (E) Shift lever held in "+" Below 13 Ω
K29-1 (SFTU) - K29-2 (E) Shift lever in S 10 kΩ or higher
K29-3 (SFTD) - K29-2 (E) Shift lever held in "-" Below 13 Ω
K29-3 (SFTD) - K29-2 (E) Shift lever in S 10 kΩ or higher



c.

Reconnect the K29 transmission control switch (shift lock control unit assembly) connector.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

NG

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Disconnect the K70 hybrid vehicle control ECU assembly connector.


b.

Disconnect the K22 spiral cable sub-assembly connector. (w/ Shift paddle switch)


c.
C264019C61
2.427,2.563 2.823,2.781 0.396,0.219 2.094,2.25 2.75,1.917 true 3.104,2.25 2.792,1.917 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.885,2.281 2.313,2.479 0.427,0.198 10 false SFTU 2.969,2.271 3.396,2.469 0.427,0.198 10 false SFTD 2.5,2.594 2.927,2.792 0.427,0.198 10 false K70
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)


Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard Resistance:
Tester Connection Condition Specified Condition
K70-9 (SFTU) - Body ground Shift lever held in "+" Below 13 Ω
Shift lever in S 10 kΩ or higher
K70-8 (SFTD) - Body ground Shift lever held in "-" Below 13 Ω
Shift lever in S 10 kΩ or higher



d.

Reconnect the K22 spiral cable sub-assembly connector. (w/ Shift paddle switch)


e.

Reconnect the K70 hybrid vehicle control ECU assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR