Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM
RM33C0E _58 Vehicle Interior _065460 SUPPLEMENTAL RESTRAINT SYSTEMS _0331858 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1771  Passenger Side Buckle Switch Circuit Malfunction  


DESCRIPTION

The front passenger side buckle switch circuit consists of the occupant detection ECU and front passenger side buckle switch (front seat inner belt assembly RH).

DTC B1771 is stored when a malfunction is detected in the front passenger side buckle switch circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1771 Passenger Side Buckle Switch Circuit Malfunction
·

The occupant detection ECU detects a line short, short to ground or B+, or an open in the front passenger side buckle switch circuit.

·

Front passenger side buckle switch malfunction

·

Occupant detection ECU malfunction


·

Front seat wire RH

·

Front passenger side buckle switch (Front seat inner belt assembly RH)

·

Occupant detection ECU



WIRING DIAGRAM

B474759E08
5.01,3.083 6.76,3.531 1.75,0.448 10 false Occupant Detection ECU 5,2.917 6.323,3.365 1.323,0.448 10 false a6 5.052,1.083 6.375,1.531 1.323,0.448 10 false BSW 5.052,1.99 6.375,2.438 1.323,0.448 10 false BGND 4.865,1.083 6.188,1.531 1.323,0.448 10 false 7 4.865,1.99 6.188,2.438 1.323,0.448 10 false 9 2.292,1.083 3.615,1.531 1.323,0.448 10 false 1 2.292,1.979 3.615,2.427 1.323,0.448 10 false 2 0.708,2.531 2.031,2.979 1.323,0.448 10 false a3 0.708,2.708 3,3.396 2.292,0.688 10 false Front Passenger Side Buckle Switch (Front Seat Inner Belt Assembly RH) 5.854,0.406 6.344,0.802 0.49,0.396 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

When DTC B1650 is stored as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant detection ECU. When DTC B1771 is output, perform troubleshooting for this DTC first.

·

If it is difficult to perform troubleshooting (wire harness inspection), remove the front passenger seat installation bolts to see under the seat cushion.

·

In the above case, lift and hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.



PROCEDURE

1.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Check that the connectors are properly connected to the occupant detection ECU and front seat inner belt assembly RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the occupant detection ECU and front seat inner belt assembly RH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK FRONT SEAT WIRE RH

NG

REPLACE FRONT SEAT WIRE RH

2.CHECK FRONT SEAT WIRE RH
a.
C290337C16
0.375,3.458 0.708,3.688 0.333,0.229 0.958,0.635 1.281,0.865 0.323,0.229 1.917,0.823 1.583,1.365 false 1.417,1.927 1.583,1.927 1.583,1.927 1.583,2.344 false 1.719,4.167 2.135,4.167 false 2.167,0.823 2.51,1.354 false 0.667,2.323 1.063,2.646 0.396,0.323 10 false *1 2.479,2.177 2.875,2.5 0.396,0.323 10 false *2 1.271,1.854 1.583,2.104 0.313,0.25 10 false *3 2.156,4.094 2.552,4.344 0.396,0.25 10 false *4 0.823,0.177 1.24,0.677 0.417,0.5 10 false *a 0.167,3.01 0.5,3.333 0.333,0.323 10 false *b 2.146,2.344 2.542,2.667 0.396,0.323 10 false A 1.865,2.344 2.26,2.667 0.396,0.323 10 false B 1.24,2.344 1.635,2.667 0.396,0.323 10 false C 0.958,2.333 1.354,2.656 0.396,0.323 10 false D 1.417,1.365 1.833,1.865 0.417,0.5 10 false BSW 0.469,3.49 0.865,3.74 0.396,0.25 10 false a3 1.052,0.667 1.448,0.917 0.396,0.25 10 false a6 2.323,1.365 2.823,1.844 0.5,0.479 10 false BGND
*1 Front Seat Inner Belt Assembly RH
*2 Occupant Detection ECU
*3 Front Seat Wire RH
*4 Service Wire
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Front view of wire harness connector
(to Front Seat Inner Belt Assembly RH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
a6-7 (BSW) - Body ground Power switch on (IG) Below 1 V
a6-9 (BGND) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.


f.

Using a service wire, connect terminals 1 and 2 of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a6-7 (BSW) - a6-9 (BGND) Always Below 1 Ω



h.

Disconnect the service wire from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a6-7 (BSW) - a6-9 (BGND) Always 1 MΩ or higher
a6-7 (BSW) - Body ground Always 1 MΩ or higher
a6-9 (BGND) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK DTC

NG

REPLACE FRONT SEAT WIRE RH

3.CHECK DTC
a.

Connect the connectors to the occupant detection ECU and front seat inner belt assembly RH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG), and wait for at least 60 seconds.


d.

Clear the DTCs stored in the occupant detection ECU.

Body Electrical > Occupant Detection > Clear DTCs
50002 394

e.

Clear the DTCs stored in the airbag sensor assembly.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 10 seconds.


h.

Check for DTCs.

Body Electrical > Occupant Detection > Trouble Codes
50001 394
OK:

DTC B1771 is not output.


HINT:

Codes other than DTC B1771 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

NG

4.CHECK FRONT SEAT INNER BELT ASSEMBLY RH
4.CHECK FRONT SEAT INNER BELT ASSEMBLY RH
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Replace the front seat inner belt assembly RH with a known good one.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL

HINT:

Perform the following inspection using known good parts from another vehicle if possible.



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG), and wait for at least 60 seconds.


e.

Clear the DTCs stored in the occupant detection ECU.

Body Electrical > Occupant Detection > Clear DTCs
50002 394

f.

Clear the DTCs stored in the airbag sensor assembly.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

g.

Turn the power switch off.


h.

Turn the power switch on (IG), and wait for at least 10 seconds.


i.

Check for DTCs.

Body Electrical > Occupant Detection > Trouble Codes
50001 394
OK:

DTC B1771 is not output.


HINT:

Codes other than DTC B1771 may be output at this time, but they are not related to this check.



j.

Turn the power switch off.


k.

Disconnect the cable from the negative (-) auxiliary battery terminal.


l.

Restore the front seat inner belt assembly RH that was installed for testing to its original location.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL


Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

NG

5.REPLACE OCCUPANT DETECTION ECU
5.REPLACE OCCUPANT DETECTION ECU
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Replace the occupant detection ECU with a new one.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL


d.

Connect the cable to the negative (-) auxiliary battery terminal.


Result:
Proceed to
NEXT



NEXT

6.PERFORM ZERO POINT CALIBRATION
6.PERFORM ZERO POINT CALIBRATION
a.

Result:
Proceed to
NEXT



NEXT

END