Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM
RM33C0E _59 Vehicle Exterior _065468 SLIDING ROOF / CONVERTIBLE _0332024 SLIDING ROOF SYSTEM J

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  Sliding Roof does not Move by Operating Sliding Roof Control Switch  


DESCRIPTION

The sliding roof ECU (sliding roof drive gear sub-assembly) receives slide and tilt signals and operates its built-in motor when the sliding roof switch (roof console box sub-assembly) is operated.

WIRING DIAGRAM

B454519E05
0.396,4.823 3.76,5.208 3.365,0.385 10 false Sliding Roof Switch (Roof Console Box Sub-assembly) 4.635,4.792 6.573,5.25 1.938,0.458 10 true Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly) 1.208,1.104 2.719,1.354 1.51,0.25 10 false from IG1-NO. 1 Relay 2.156,2.771 3.667,3.021 1.51,0.25 10 false UP 1.906,3.146 3.417,3.396 1.51,0.25 10 false DOWN 3.177,1.292 4.688,1.542 1.51,0.25 10 false ECU-IG1 NO. 3 4.438,1.021 4.698,1.292 0.26,0.271 10 false IG 4.427,2.01 5.938,2.26 1.51,0.25 10 false OPN 4.458,2.396 5.969,2.646 1.51,0.25 10 false CLS 4.438,2.781 5.948,3.031 1.51,0.25 10 false OPN 4.438,3.156 5.948,3.406 1.51,0.25 10 false CLS 4.438,3.521 4.958,3.896 0.521,0.375 10 false E 2.042,2.01 3.552,2.26 1.51,0.25 10 false OPN 2.052,2.396 3.563,2.646 1.51,0.25 10 false CLS 2.031,3.531 3.542,3.781 1.51,0.25 10 false GND 0.406,4.656 1.917,4.906 1.51,0.25 10 false V14 4.677,4.625 6.188,4.875 1.51,0.25 10 false V2 4.24,1.01 4.5,1.281 0.26,0.271 10 false 6 4.188,2.01 4.448,2.281 0.26,0.271 10 false 10 4.26,2.375 4.521,2.646 0.26,0.271 10 false 8 4.26,2.74 4.521,3.01 0.26,0.271 10 false 5 4.26,3.125 4.521,3.396 0.26,0.271 10 false 9 4.271,3.521 4.531,3.792 0.26,0.271 10 false 2 2.448,1.979 2.708,2.25 0.26,0.271 10 false 5 2.438,2.385 2.698,2.656 0.26,0.271 10 false 4 2.427,2.76 2.688,3.031 0.26,0.271 10 false 3 2.417,3.146 2.677,3.417 0.26,0.271 10 false 18 2.417,3.531 2.677,3.802 0.26,0.271 10 false 15

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the sliding roof ECU (sliding roof drive gear sub-assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear sub-assembly) must be initialized.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION

·

If a sliding roof ECU (sliding roof drive gear sub-assembly) DTC is output, first perform troubleshooting for the sliding roof ECU (sliding roof drive gear sub-assembly) DTC.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SLIDING ROOF)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Sliding Roof / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Sliding Roof > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Slide Roof Operate sliding roof motor OFF / Opn/Dwn / Clos/Up -
Body Electrical > Sliding Roof > Active Test
Tester Display
Slide Roof
50004 147 1
OK:

Slide roof is operated using GTS.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS

NG

5.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) - IG POWER SUPPLY AND BODY GROUND)
2.READ VALUE USING GTS
a.

Enter the following menus: Body Electrical / Sliding Roof / Data List.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Sliding Roof > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Open Switch OPEN switch signal OFF or ON OFF: OPEN switch not pressed
ON: OPEN switch pressed
-
Close Switch CLOSE switch signal OFF or ON OFF: CLOSE switch not pressed
ON: CLOSE switch pressed
-
Up Switch UP switch signal OFF or ON OFF: UP switch not pressed
ON: UP switch pressed
-
Down Switch DOWN switch signal OFF or ON OFF: DOWN switch not pressed
ON: DOWN switch pressed
-
Body Electrical > Sliding Roof > Data List
Tester Display
Open Switch
Close Switch
Up Switch
Down Switch
50003 147 1,4,7,10
OK:

The GTS display changes according to the operation of each switch as shown in the table.



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

NG

3.INSPECT SLIDING ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY)
3.INSPECT SLIDING ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY)
a.

Remove the sliding roof switch (roof console box sub-assembly).

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>REMOVAL


b.

Inspect the sliding roof switch (roof console box sub-assembly).

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) - SLIDING ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY) AND BODY GROUND)

NG

REPLACE SLIDING ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) - SLIDING ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY) AND BODY GROUND)
a.

Disconnect the V14 sliding roof switch (roof console box sub-assembly) connector.


b.

Disconnect the V2 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V2-8 (CLS) - V14-4 (CLS) Always Below 1 Ω
V2-8 (CLS) or V14-4 (CLS) - Body ground Always 10 kΩ or higher
V2-10 (OPN) - V14-5 (OPN) Always Below 1 Ω
V2-10 (OPN) or V14-5 (OPN) - Body ground Always 10 kΩ or higher
V2-9 (CLS) - V14-18 (DOWN) Always Below 1 Ω
V2-9 (CLS) or V14-18 (DOWN) - Body ground Always 10 kΩ or higher
V2-5 (OPN) - V14-3 (UP) Always Below 1 Ω
V2-5 (OPN) or V14-3 (UP) - Body ground Always 10 kΩ or higher
V14-15 (GND) - Body ground Always Below 1 Ω
V2-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) - IG POWER SUPPLY AND BODY GROUND)
a.
B425565C17
1.469,0.167 1.917,0.385 0.448,0.219 2.479,1.802 1.958,1.354 false 2.479,0.979 1.969,1.094 false 1.604,0.177 1.917,0.375 0.313,0.198 10 false V2 2.552,1.802 2.875,2.042 0.323,0.24 10 false IG 0.146,0.104 0.531,0.427 0.385,0.323 10 false *a 2.573,0.896 2.896,1.135 0.323,0.24 10 false E
*a Front view of wire harness connector
(to Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly))


Disconnect the V2 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
V2-6 (IG) - Body ground Power switch on (IG) 11 to 14 V
V2-6 (IG) - Body ground Power switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V2-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR