Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module) › 2017.09–2018.08
RM33C0E _51 Engine / Hybrid System _065419 A25A-FXS ENGINE CONTROL _0332275 SFI SYSTEM(w/ Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P012800  Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)  


DESCRIPTION

The ECM uses the engine coolant temperature sensor, installed to the water outlet, and the No. 2 engine coolant temperature sensor, installed to the radiator pipe assembly, to monitor the operation of the thermostat.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P012800 Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) Either of the following conditions is met (2 trip detection logic):
·

All of the following conditions are met for 5 seconds or more:

(a)

The engine is started cold and then warmed up.

(b)

When the estimated engine coolant temperature is 75°C (167°F) or higher, the actual engine coolant temperature is less than 75°C (167°F).


·

All of the following conditions are met for certain period of time:

(a)

Cold start.

(b)

The engine is running and the engine coolant temperature is increasing.

(c)

The temperature detected by the No. 2 engine coolant temperature sensor is higher than the threshold temperature calculated based on the engine coolant temperature sensor value.



·

Water inlet with thermostat sub-assembly (thermostat)

·

Cooling system

·

Engine coolant temperature sensor

·

No. 2 engine coolant temperature sensor

·

ECM


Comes on DTC stored SAE Code: P0128

MONITOR DESCRIPTION

Engine Coolant Temperature Sensor Output Judgment by Simulated Engine Coolant Temperature
A121605E47
4.917,2.323 5.302,2.594 false 3.833,2.083 3.719,0.885 3.719,0.885 3.583,0.885 false 4.656,2.615 6.302,2.958 1.646,0.344 10 false Indicated Engine Coolant Temperature Reading 3.104,3.719 5.344,3.927 2.24,0.208 10 false DTC Stored (after 2 Driving Cycles) 2.229,0.792 3.563,1.188 1.333,0.396 10 false Estimated Engine Coolant Temperature 0.708,1.698 1.833,1.896 1.125,0.198 10 false Threshold (75°C) 4.323,1.073 5.219,1.417 0.896,0.344 10 false 5 seconds 1.104,2.74 2.125,3.094 1.021,0.354 10 false Engine Coolant Temperature 2.26,3.354 2.604,3.563 0.344,0.208 10 false Time

The ECM estimates the engine coolant temperature based on the starting temperature, engine load, and engine speed. The ECM then compares the estimated temperature with the actual engine coolant temperature. When the estimated engine coolant temperature reaches 75°C (167°F), the ECM checks the actual engine coolant temperature. If the actual engine coolant temperature is less than 75°C (167°F), the ECM interprets this as a malfunction of the thermostat or in the engine cooling system, illuminate the MIL and stores this DTC.


Stuck Open Detection with No. 2 Engine Coolant Temperature Sensor
A375761E01
3.406,3.698 3.698,3.698 3.698,3.698 3.948,2.917 true 5.646,2.125 5.448,2.125 5.448,2.125 5.313,1.781 true 3.625,0.25 3.938,0.25 3.938,0.25 3.698,1.646 true 5.219,0.448 5.021,0.448 5.021,0.448 5.281,1.365 true 0.896,0.844 1.854,1.448 0.958,0.604 10 false Engine Coolant Temperature 5.594,3.323 6.552,3.927 0.958,0.604 10 false Time 4.021,3.75 7.031,4.323 3.01,0.573 10 false DTC Stored (after 2 Driving Cycles) ([A] and [B] is [Judgment timer x 0.7] seconds or more) 2.938,1.104 3.281,1.448 0.344,0.344 10 false [A] 4.625,1.125 4.969,1.469 0.344,0.344 10 false [B] 5.708,2.042 7.125,2.417 1.417,0.375 10 false Threshold Temperature 5.292,0.365 7.042,0.844 1.75,0.479 10 false Engine Coolant Temperature Sensor Value 0.615,0.156 3.594,0.677 2.979,0.521 10 false No. 2 Engine Coolant Temperature Sensor Value (with Stuck Open Thermostat) 0.396,3.604 3.375,4.125 2.979,0.521 10 false No. 2 Engine Coolant Temperature Sensor Value (with Normal Thermostat)

If the temperature detected by the No. 2 engine coolant temperature sensor value is higher than the threshold temperature calculated based on the engine coolant temperature sensor value for (judgment timer x 0.7) seconds or more cumulatively while the engine coolant temperature is increasing, the ECM will determine that the thermostat is stuck open, illuminate the MIL and store this DTC.


MONITOR STRATEGY

Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

A402681E01
0.469,1.24 2.156,1.5 1.688,0.26 10 false 80 km/h [Engine Running] 0.802,2.552 2.25,2.854 1.448,0.302 10 false Power Switch on (IG) 1.729,2.24 2.271,2.479 0.542,0.24 10 false Idling 3.99,3.135 4.958,3.417 0.969,0.281 10 false 15 minutes 2.479,2.427 3.021,2.667 0.542,0.24 10 false [A] 4.229,1.115 4.771,1.354 0.542,0.24 10 false [B] 5.281,3.406 5.823,3.646 0.542,0.24 10 false [C] 2.625,0.031 6.604,0.26 3.979,0.229 10 false - Engine coolant temperature when engine started: 56°C or less 2.635,0.354 6.167,0.573 3.531,0.219 10 false - Intake air temperature when engine started: 0 to 35°C 2.635,0.698 7.156,0.896 4.521,0.198 10 false - Heater control set to MAX HOT with fresh air mode selected and A/C off

1.

Turn the power switch off and leave the vehicle for several hours.

2.

Connect the GTS to the DLC3.

3.

Turn the power switch on (IG) [A].

4.

Turn the GTS on.

5.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature and Intake Air Temperature.

6.

Check that the value of the Data List item Coolant Temperature is 56°C (133°F) or less and the value of the Data List item Intake Air Temperature is between 0 and 35°C (32 and 95°F).

7.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

8.

Start the engine.

9.

Set the heater control to MAX HOT with fresh air mode selected and turn the A/C off.

10.

With the engine running, drive the vehicle at 80 km/h (50 mph) for 15 minutes [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


11.

After the value of the Data List item Coolant Temperature stabilizes, check that it is 75°C (167°F) or higher.

HINT:

If the value of the Data List item Coolant Temperature is less than 75°C (167°F) while driving the vehicle at 80 km/h (50 mph), inspect the cooling system and thermostat.


12.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

15.

Input the DTC: P012800.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, let the engine cool down (engine coolant temperature is 56°C (133°F) or less), and then perform steps [A] through [C].




CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY



HINT:
·

When this DTC is output, check the engine coolant temperature using the GTS. Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature. If the value of Coolant Temperature is lower than the actual engine coolant temperature, the engine coolant temperature sensor circuit may be malfunctioning. In this case, check the wire harnesses and connectors (and their connection condition) between the ECM and the engine coolant temperature sensor first.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P012800)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P012800 is output A
DTC P012800 and other DTCs are output B


HINT:

If any DTCs other than P012800 are output, troubleshoot those DTCs first.




A

2.CHECK ENGINE COOLING SYSTEM

B

2.CHECK ENGINE COOLING SYSTEM
a.

Check for defects in the engine cooling system that might cause the system to be excessively cold, such as abnormal cooling fan operation or any modifications.


Result:
Proceed to
OK
NG



OK

3.INSPECT WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

NG

REPAIR OR REPLACE ENGINE COOLING SYSTEM

3.INSPECT WATER INLET WITH THERMOSTAT SUB-ASSEMBLY
a.

Inspect the water inlet with thermostat sub-assembly (thermostat opening temperature).

Click hereEngine / Hybrid System>A25A-FXS (COOLING)>THERMOSTAT>INSPECTION


Result:
Proceed to
OK
NG



OK

4.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

NG

REPLACE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

4.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION


Result:
Proceed to
OK
NG



OK

5.INSPECT NO. 2 ENGINE COOLANT TEMPERATURE SENSOR

NG

5.INSPECT NO. 2 ENGINE COOLANT TEMPERATURE SENSOR
a.

Inspect the No. 2 engine coolant temperature sensor.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE NO. 2 ENGINE COOLANT TEMPERATURE SENSOR