The main body ECU (multiplex network body ECU) and windshield wiper motor assembly communicate via LIN communication. The main body ECU (multiplex network body ECU) stores this DTC if communication becomes abnormal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | DTC Output from |
|---|---|---|---|---|---|
| B1245 | Lost Communication with Wiper ECU LIN | Detection condition:
Auxiliary battery voltage is 9.5 V or more Malfunction Status:
A communication malfunction between the main body ECU (multiplex network body ECU) and windshield wiper motor assembly Malfunction Time:
10 seconds or more |
·
Windshield wiper motor assembly ·
Main body ECU (multiplex network body ECU) ·
Harness or connector |
○ | Main Body |
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| Only DTC B1245 is output | A |
| DTC B1245 and B1373 are output | B |
A
B
Disconnect the K51 main body ECU (multiplex network body ECU) connector.
Disconnect the A31 windshield wiper motor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K51-3 (LIN3) - A31-2 (LIN) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K51-3 (LIN3) - A31-3 (LIN) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Main Body ECU (Multiplex Network Body ECU) |
Check for voltage and pulses according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K51-3 (LIN3) - Body ground | Power switch off | Below 1 V |
| Power switch on (IG) | Pulse generation |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A31-4 (+B) - Body ground | Power switch on (IG) | 11 to 14 V |
| Less than approximately 60 seconds after power switch turned off | 11 to 14 V | |
| Approximately 60 seconds after power switch turned off | Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A31-1 (+B) - Body ground | Power switch on (IG) | 11 to 14 V |
| Less than approximately 60 seconds after power switch turned off | 11 to 14 V | |
| Approximately 60 seconds after power switch turned off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A31-1 (GND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A31-4 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG