Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) › 2017.09–2018.04
RM33C0E _58 Vehicle Interior _065462 SEAT _0333598 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2651  Reclining Sensor Malfunction  


DESCRIPTION

When the position control ECU assembly (driver seat) does not receive a reclining motor position sensor signal despite the seat having been moved forward or rearward by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2651 Reclining Sensor Malfunction Reclining motor position sensor signal not received when power seat moved forward or rearward
·

Position control ECU assembly (driver seat)

·

Reclining motor (Front seatback frame sub-assembly (driver seat))

·

Wire harness or connector



WIRING DIAGRAM

E360044E63
4.802,0.552 5.115,0.75 0.313,0.198 10 false a29 4.823,0.313 5.135,0.51 0.313,0.198 10 false 10 4.802,1.073 5.115,1.271 0.313,0.198 10 false a30 4.885,0.833 5.198,1.031 0.313,0.198 10 false 6 4.802,1.573 5.115,1.771 0.313,0.198 10 false a31 4.854,1.354 5.167,1.552 0.313,0.198 10 false 11 4.813,2.094 5.125,2.292 0.313,0.198 10 false a31 4.854,1.875 5.167,2.073 0.313,0.198 10 false 12 5.25,0.563 5.75,0.76 0.5,0.198 10 false RCL+ 5.25,1.063 5.75,1.26 0.5,0.198 10 false RCL- 5.25,1.573 5.75,1.771 0.5,0.198 10 false SSRR 5.25,2.104 5.75,2.302 0.5,0.198 10 false SENG 2.208,0.448 2.708,0.646 0.5,0.198 10 false 1 2.219,0.969 2.719,1.167 0.5,0.198 10 false 4 2.219,1.479 2.719,1.677 0.5,0.198 10 false 2 2.219,1.99 2.719,2.188 0.5,0.198 10 false 3 1.313,2.458 1.813,2.656 0.5,0.198 10 false q1 1.313,2.615 2.417,2.885 1.104,0.271 10 false Reclining Motor 0.271,3.083 3.469,3.417 3.198,0.333 10 false Front Seatback Frame Sub-assembly (Driver Seat) 4.792,2.594 6.75,2.99 1.958,0.396 10 false Position Control ECU Assembly (Driver Seat)

PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2651 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.PERFORM ACTIVE TEST USING GTS (SEAT RECLINING OPERATION)
3.PERFORM ACTIVE TEST USING GTS (SEAT RECLINING OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Seat Reclining Seat reclining operation OFF/Rear/Front -
Body Electrical > Driver Seat > Active Test
Tester Display
Seat Reclining
50004 162 1
OK:

Reclining motor operates normally.



Result:
Proceed to
OK
NG



OK

4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (RECLINING MOTOR CIRCUIT)

NG

7.INSPECT RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT))
4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (RECLINING MOTOR CIRCUIT)
a.

Disconnect the q1 reclining motor (front seatback frame sub-assembly (driver seat)) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
q1-2 - q1-3 Reclining switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

5.CHECK RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT))

NG

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT)))
5.CHECK RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT))
a.
B343020C54
1.5,0.167 1.917,0.417 0.417,0.25 0.156,0.146 0.396,0.396 0.24,0.25 10 false *a 1.625,0.198 2,0.469 0.375,0.271 10 false q1
*a Component with harness connected
(Reclining Motor (Front Seatback Frame Sub-assembly (Driver Seat)))


Reconnect the q1 reclining motor (front seatback frame sub-assembly (driver seat)) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
q1-2 - Body ground Reclining motor operating 4.5 to 4.8 V



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPLACE RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT))

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT)))
a.

Disconnect the a31 position control ECU assembly (driver seat) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a31-11 (SSRR) - q1-2 Always Below 1 Ω
a31-11 (SSRR) or q1-2 - Body ground Always 10 kΩ or higher
a31-12 (SENG) - q1-3 Always Below 1 Ω
a31-12 (SENG) or q1-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT))
a.

Remove the reclining motor (front seatback frame sub-assembly (driver seat)).

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY


b.

Inspect the reclining motor (front seatback frame sub-assembly (driver seat)).

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT)))

NG

REPLACE RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT))

8.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT)))
a.

Disconnect the a29 and a30 position control ECU assembly (driver seat) connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a29-10 (RCL+) - q1-1 Always Below 1 Ω
a29-10 (RCL+) or q1-1 - Body ground Always 10 kΩ or higher
a30-6 (RCL-) - q1-4 Always Below 1 Ω
a30-6 (RCL-) or q1-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR