Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) › 2017.09–2018.04
RM33C0E _58 Vehicle Interior _065462 SEAT _0333598 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2652  Front Vertical Sensor Malfunction  


DESCRIPTION

When the position control ECU assembly (driver seat) does not receive a front vertical motor position sensor signal despite the seat having been moved upward or downward by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2652 Front Vertical Sensor Malfunction Front vertical motor position sensor signal not received when power seat moved upward or downward
·

Position control ECU assembly (driver seat)

·

Power seat tilt motor assembly (driver seat)

·

Wire harness or connector



WIRING DIAGRAM

B493362E03
2.198,0.438 2.604,0.667 0.406,0.229 10 false 1 2.208,0.969 2.615,1.198 0.406,0.229 10 false 4 2.208,1.458 2.615,1.688 0.406,0.229 10 false 2 2.208,1.979 2.615,2.208 0.406,0.229 10 false 3 0.823,2.385 1.229,2.615 0.406,0.229 10 false a33 0.813,2.563 2.813,2.99 2,0.427 10 false Power Seat Tilt Motor Assembly (Driver Seat) 0.458,3.333 3.323,3.604 2.865,0.271 10 false Front Seat Adjuster Assembly (Driver Seat) 4.75,2.594 6.698,3.115 1.948,0.521 10 false Position Control ECU Assembly (Driver Seat) 5.219,2.094 5.76,2.313 0.542,0.219 10 false SENG 5.25,1.573 5.802,1.823 0.552,0.25 10 false SSFV 5.229,0.552 5.719,0.781 0.49,0.229 10 false FRV+ 4.802,0.531 5.208,0.76 0.406,0.229 10 false a29 4.813,1.052 5.219,1.281 0.406,0.229 10 false a30 4.844,0.302 5.25,0.531 0.406,0.229 10 false 7 4.865,0.823 5.271,1.052 0.406,0.229 10 false 4 4.823,1.333 5.229,1.563 0.406,0.229 10 false 10 4.823,1.844 5.229,2.073 0.406,0.229 10 false 12 4.813,1.563 5.219,1.792 0.406,0.229 10 false a31 4.802,2.094 5.208,2.323 0.406,0.229 10 false a31 5.24,1.083 5.729,1.313 0.49,0.229 10 false FRV-

PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2652 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.PERFORM ACTIVE TEST USING GTS (SEAT FRONT VERTICAL OPERATION)
3.PERFORM ACTIVE TEST USING GTS (SEAT FRONT VERTICAL OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Front Vertical Operation Seat front vertical operation OFF/Down/Up -
Body Electrical > Driver Seat > Active Test
Tester Display
Front Vertical Operation
50004 162 3
OK:

Front vertical motor operates normally.



Result:
Proceed to
OK
NG



OK

4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (FRONT VERTICAL MOTOR CIRCUIT)

NG

7.INSPECT POWER SEAT TILT MOTOR ASSEMBLY (DRIVER SEAT)
4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (FRONT VERTICAL MOTOR CIRCUIT)
a.

Disconnect the a33 power seat tilt motor assembly (driver seat) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
a33-2 - a33-3 Front vertical switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

5.CHECK POWER SEAT TILT MOTOR ASSEMBLY (DRIVER SEAT)

NG

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - POWER SEAT TILT MOTOR ASSEMBLY (DRIVER SEAT))
5.CHECK POWER SEAT TILT MOTOR ASSEMBLY (DRIVER SEAT)
a.
B343020C55
1.5,0.198 1.917,0.448 0.417,0.25 0.156,0.146 0.396,0.396 0.24,0.25 10 false *a 1.583,0.24 1.958,0.51 0.375,0.271 10 false a33
*a Component with harness connected
(Power Seat Tilt Motor Assembly (Driver Seat))


Reconnect the a33 power seat tilt motor assembly (driver seat) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
a33-2 - Body ground Front vertical motor operating 4.5 to 4.8 V



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPLACE POWER SEAT TILT MOTOR ASSEMBLY (DRIVER SEAT)

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - POWER SEAT TILT MOTOR ASSEMBLY (DRIVER SEAT))
a.

Disconnect the a31 position control ECU assembly (driver seat) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a31-10 (SSFV) - a33-2 Always Below 1 Ω
a31-10 (SSFV) or a33-2 - Body ground Always 10 kΩ or higher
a31-12 (SENG) - a33-3 Always Below 1 Ω
a31-12 (SENG) or a33-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT POWER SEAT TILT MOTOR ASSEMBLY (DRIVER SEAT)
a.

Remove the power seat tilt motor assembly (driver seat).

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY


b.

Inspect the power seat tilt motor assembly (driver seat).

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - POWER SEAT TILT MOTOR ASSEMBLY (DRIVER SEAT))

NG

REPLACE POWER SEAT TILT MOTOR ASSEMBLY (DRIVER SEAT)

8.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - POWER SEAT TILT MOTOR ASSEMBLY (DRIVER SEAT))
a.

Disconnect the a29 and a30 position control ECU assembly (driver seat) connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a29-7 (FRV+) - a33-1 Always Below 1 Ω
a29-7 (FRV+) or a33-1 - Body ground Always 10 kΩ or higher
a30-4 (FRV-) - a33-4 Always Below 1 Ω
a30-4 (FRV-) or a33-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR