Home › Vehicle Interior › SEAT › CLIMATE CONTROL SEAT SYSTEM
RM33C0E _58 Vehicle Interior _065462 SEAT _0333602 CLIMATE CONTROL SEAT SYSTEM J

SEAT  CLIMATE CONTROL SEAT SYSTEM  Climate Control Seat System does not Operate  


DESCRIPTION

When the power switch is on (IG) and the refreshing seat switch is operated, the air conditioning amplifier assembly receives refreshing seat switch position signals and then sends airflow amount signals to each seat cushion climate control blower assembly.

WIRING DIAGRAM

B520545E28
1.198,0.656 1.604,0.865 0.406,0.208 10 false LIN1 1.146,2.438 1.594,2.635 0.448,0.198 10 false ROUT 1.167,6.458 1.615,6.656 0.448,0.198 10 false LOUT 1.625,0.5 1.938,0.698 0.313,0.198 10 false 14 1.583,6.323 1.896,6.521 0.313,0.198 10 false 24 1.594,2.313 1.906,2.51 0.313,0.198 10 false 23 2.688,0.5 2.844,0.698 0.156,0.198 10 false 3 4.125,0.271 4.365,0.49 0.24,0.219 10 false 1 4.135,0.865 4.333,1.073 0.198,0.208 10 false 5 2.698,2.719 2.896,2.927 0.198,0.208 10 false 1 2.698,2.292 2.896,2.5 0.198,0.208 10 false 7 2.74,3.167 2.938,3.375 0.198,0.208 10 false 8 4.104,2.75 4.302,2.958 0.198,0.208 10 false 6 4.104,3.146 4.333,3.396 0.229,0.25 10 false 4 3.667,5.198 4.74,5.417 1.073,0.219 10 false S/HTR MAIN 5.417,0.375 6.854,0.594 1.438,0.219 10 false from IG1 NO. 1 Relay 2.74,1.302 3.198,1.5 0.458,0.198 10 false K49 5.375,7.156 5.833,7.354 0.458,0.198 10 false c3 5.354,3.677 5.813,3.875 0.458,0.198 10 false q2 2.813,7.177 3.271,7.375 0.458,0.198 10 false b18 0.375,7.208 1.021,7.438 0.646,0.229 10 false K54 2.844,3.677 3.302,3.875 0.458,0.198 10 false a34 2.74,1.469 5.26,1.771 2.521,0.302 10 false Refreshing Seat Switch 2.01,3.021 3.156,3.229 1.146,0.208 10 false S/HTR F/R 2.031,6.156 3.115,6.396 1.083,0.24 10 false S/HTR F/L 4.688,5.031 6.646,5.354 1.958,0.323 10 false from Auxiliary Battery 2.896,0.656 3.323,0.958 0.427,0.302 10 false SLIN 3.833,0.385 4.083,0.583 0.25,0.198 10 false IG 3.885,0.969 4.042,1.167 0.156,0.198 10 false E 5.24,2.271 5.438,2.479 0.198,0.208 10 false 1 5.25,2.708 5.448,2.917 0.198,0.208 10 false 3 5.24,3.167 5.438,3.375 0.198,0.208 10 false 4 5.271,5.917 5.469,6.125 0.198,0.208 10 false 1 4.094,2.323 4.292,2.531 0.198,0.208 10 false 5 2.76,6.313 2.917,6.51 0.156,0.198 10 false 7 4.104,6.667 4.26,6.865 0.156,0.198 10 false 4 4.104,6.313 4.26,6.51 0.156,0.198 10 false 6 4.115,5.938 4.271,6.135 0.156,0.198 10 false 5 5.271,6.646 5.521,6.833 0.25,0.188 10 false 4 5.271,6.271 5.427,6.469 0.156,0.198 10 false 3 2.771,6.656 2.927,6.854 0.156,0.198 10 false 8 2.75,5.917 2.906,6.115 0.156,0.198 10 false 1 2.813,7.344 4.667,7.719 1.854,0.375 10 false Seat Cushion Climate Control Blower Assembly LH 2.823,3.854 4.667,4.302 1.844,0.448 10 false Seat Cushion Climate Control Blower Assembly RH 5.375,3.875 6.521,4.24 1.146,0.365 10 false Seatback Climate Control Blower RH 5.375,7.313 6.5,7.76 1.125,0.448 10 false Seatback Climate Control Blower LH 0.333,7.375 1.896,7.792 1.563,0.417 10 false Air Conditioning Amplifier Assembly 0.75,8.427 2.458,8.667 1.708,0.24 10 false : LIN Communication Line 2.917,2.844 3.438,3.146 0.521,0.302 10 false IG 2.927,2.417 3.448,2.719 0.521,0.302 10 false SIGN 2.927,3.292 3.448,3.594 0.521,0.302 10 false GND 3.74,2.417 4.26,2.719 0.521,0.302 10 false CTB 3.719,2.844 4.24,3.146 0.521,0.302 10 false BBS 3.708,3.26 4.229,3.563 0.521,0.302 10 false BFB- 5.417,3.25 5.938,3.552 0.521,0.302 10 false IG 5.396,2.813 5.917,3.115 0.521,0.302 10 false BFB+ 5.385,2.427 5.906,2.729 0.521,0.302 10 false GND 2.917,6.021 3.438,6.323 0.521,0.302 10 false IG 2.896,6.458 3.417,6.76 0.521,0.302 10 false SIGN 2.906,6.802 3.427,7.104 0.521,0.302 10 false GND 3.771,6.042 4.292,6.344 0.521,0.302 10 false CTB 3.75,6.406 4.271,6.708 0.521,0.302 10 false BBS 3.719,6.792 4.24,7.094 0.521,0.302 10 false BFB- 5.417,6.031 5.938,6.333 0.521,0.302 10 false GND 5.417,6.406 5.938,6.708 0.521,0.302 10 false BFB+ 5.427,6.792 5.948,7.094 0.521,0.302 10 false IG 4.708,4.531 6.146,4.75 1.438,0.219 10 false from IG1 NO. 1 Relay 4.208,0.542 5.281,0.76 1.073,0.219 10 false ECU-IG1 NO. 4 3.563,4.719 4.635,4.938 1.073,0.219 10 false ECU-IG1 NO. 4 2.833,5.302 3.979,5.51 1.146,0.208 10 false S/HTR F/R 2.74,4.448 2.896,4.646 0.156,0.198 10 false 2 3.427,4.448 3.583,4.646 0.156,0.198 10 false 1 3.438,4.927 3.594,5.125 0.156,0.198 10 false 5 2.76,4.927 2.917,5.125 0.156,0.198 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The climate control seat system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the climate control seat system after confirming that the communication system is functioning properly.

Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK DTC OUTPUT
a.

Clear DTCs.

Body Electrical > Air Conditioner > Clear DTCs
50002 121

b.

Check for DTCs.

Body Electrical > Air Conditioner > Trouble Codes
50001 121
Result:
Result Proceed to
DTC B14B5 is not output A
DTC B14B5 output B




A

2.CHECK CLIMATE CONTROL SEAT OPERATION

B

2.CHECK CLIMATE CONTROL SEAT OPERATION
a.

Check the climate control seat operation.

Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>ON-VEHICLE INSPECTION

Result:
Result Proceed to
Climate control seat does not operate (for LH) A
Climate control seat does not operate (for RH) B
Both climate control seats do not operate C




A

3.CHECK CLIMATE CONTROL SEAT OPERATION (FRONT LH SEAT)

B

12.CHECK CLIMATE CONTROL SEAT OPERATION (FRONT RH SEAT)

C

21.INSPECT S/HTR F/R RELAY
3.CHECK CLIMATE CONTROL SEAT OPERATION (FRONT LH SEAT)
a.

Check the climate control seat operation.

Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>ON-VEHICLE INSPECTION

Result:
Result Proceed to
Only seatback climate control blower LH does not operate A
Only seat cushion climate control blower assembly LH does not operate B
Both seat blowers do not operate C




A

4.CHECK HARNESS AND CONNECTOR (SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH - SEATBACK CLIMATE CONTROL BLOWER LH)

B

REPLACE SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH

C

7.CHECK HARNESS AND CONNECTOR (IG POWER SUPPLY - SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH - BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH - SEATBACK CLIMATE CONTROL BLOWER LH)
a.

Disconnect the c3 seatback climate control blower LH connector.


b.

Disconnect the b18 seat cushion climate control blower assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
c3-1 (GND) - b18-5 (CTB) Always Below 1 Ω
c3-1 (GND) or b18-5 (CTB) - Body ground Always 10 kΩ or higher
c3-3 (BFB+) - b18-6 (BBS) Always Below 1 Ω
c3-3 (BFB+) or b18-6 (BBS) - Body ground Always 10 kΩ or higher
c3-4 (IG) - b18-4 (BFB-) Always Below 1 Ω
c3-4 (IG) or b18-4 (BFB-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE SEATBACK CLIMATE CONTROL BLOWER LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE SEATBACK CLIMATE CONTROL BLOWER LH
a.

Temporarily replace the seatback climate control blower LH with a new or known good one.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

6.CHECK CLIMATE CONTROL SEAT OPERATION
6.CHECK CLIMATE CONTROL SEAT OPERATION
a.

Check the climate control seat operation.

Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>ON-VEHICLE INSPECTION

OK:

The climate control seat operates normally.



Result:
Proceed to
OK
NG



OK

END (SEATBACK CLIMATE CONTROL BLOWER LH WAS DEFECTIVE)

NG

REPLACE SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH

7.CHECK HARNESS AND CONNECTOR (IG POWER SUPPLY - SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH - BODY GROUND)
a.
B416369C22
1.583,0.25 2,0.5 0.417,0.25 0.99,1.25 1.479,1.25 false 2.698,1.625 2.156,1.469 false 0.24,0.135 0.552,0.333 0.313,0.198 10 false *a 1.667,0.292 1.979,0.49 0.313,0.198 10 false b18 0.771,1.156 1.385,1.354 0.615,0.198 10 false IG 2.75,1.594 3.26,1.802 0.51,0.208 10 false GND
*a Front view of wire harness connector
(to Seat Cushion Climate Control Blower Assembly LH)


Disconnect the b18 seat cushion climate control blower assembly LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
b18-1 (IG) - Body ground Power switch on (IG) 11 to 14 V
b18-1 (IG) - Body ground Power switch off Below 1 V


Standard Resistance:
Tester Connection Condition Specified Condition
b18-8 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the K54 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b18-7 (SIGN) - K54-24 (LOUT) Always Below 1 Ω
b18-7 (SIGN) or K54-24 (LOUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Reconnect the K54 air conditioning amplifier assembly connector.


b.
B416364C09
1.75,0.5 2.167,0.75 0.417,0.25 1.406,1.792 1.823,1.375 true 0.281,0.167 0.594,0.365 0.313,0.198 10 false *a 1.823,0.542 2.135,0.74 0.313,0.198 10 false K54 0.333,3.969 0.792,4.167 0.458,0.198 10 false GND 1.24,1.854 1.854,2.052 0.615,0.198 10 false LOUT
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Reconnect the b18 seat cushion climate control blower assembly LH connector.


c.

Using an oscilloscope, check the input signal waveform.

Measurement Condition
Item Content
Tester Connection K54-24 (LOUT) - Body ground
Tool Setting 1 V/DIV., 0.5 ms/DIV.
Vehicle Condition
·

Power switch on (IG)

·

Refreshing seat switch on

(blower position)



OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH

NG

10.REPLACE REFRESHING SEAT SWITCH
10.REPLACE REFRESHING SEAT SWITCH
a.

Temporarily replace the refreshing seat switch with a new or known good one.

Click hereVehicle Interior>SEAT>SEAT HEATER SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CHECK CLIMATE CONTROL SEAT OPERATION
11.CHECK CLIMATE CONTROL SEAT OPERATION
a.

Check the climate control seat operation.

Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>ON-VEHICLE INSPECTION

OK:

The climate control seat operates normally.



Result:
Proceed to
OK
NG



OK

END (REFRESHING SEAT SWITCH WAS DEFECTIVE)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

12.CHECK CLIMATE CONTROL SEAT OPERATION (FRONT RH SEAT)
a.

Check the climate control seat operation.

Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>ON-VEHICLE INSPECTION

Result:
Result Proceed to
Only seatback climate control blower RH does not operate A
Only seat cushion climate control blower assembly RH does not operate B
Both seat blowers do not operate C




A

13.CHECK HARNESS AND CONNECTOR (SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY RH - SEATBACK CLIMATE CONTROL BLOWER RH)

B

REPLACE SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY RH

C

16.CHECK HARNESS AND CONNECTOR (IG POWER SUPPLY - SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY RH - BODY GROUND)
13.CHECK HARNESS AND CONNECTOR (SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY RH - SEATBACK CLIMATE CONTROL BLOWER RH)
a.

Disconnect the q2 seatback climate control blower RH connector.


b.

Disconnect the a34 seat cushion climate control blower assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a34-5 (CTB) - q2-1 (GND) Always Below 1 Ω
a34-5 (CTB) or q2-1 (GND) - Body ground Always 10 kΩ or higher
a34-6 (BBS) - q2-3 (BFB+) Always Below 1 Ω
a34-6 (BBS) or q2-3 (BFB+) - Body ground Always 10 kΩ or higher
q2-4 (IG) - a34-4 (BFB-) Always Below 1 Ω
q2-4 (IG) or a34-4 (BFB-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.REPLACE SEATBACK CLIMATE CONTROL BLOWER RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.REPLACE SEATBACK CLIMATE CONTROL BLOWER RH
a.

Temporarily replace the seatback climate control blower RH with a new or known good one.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

15.CHECK CLIMATE CONTROL SEAT OPERATION
15.CHECK CLIMATE CONTROL SEAT OPERATION
a.

Check the climate control seat operation.

Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>ON-VEHICLE INSPECTION

OK:

The climate control seat operates normally.



Result:
Proceed to
OK
NG



OK

END (SEATBACK CLIMATE CONTROL BLOWER RH WAS DEFECTIVE)

NG

REPLACE SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY RH

16.CHECK HARNESS AND CONNECTOR (IG POWER SUPPLY - SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY RH - BODY GROUND)
a.
B416369C23
1.563,0.24 1.979,0.49 0.417,0.25 1.021,1.49 1.479,1.25 true 2.156,1.458 2.615,1.667 true 0.24,0.135 0.552,0.333 0.313,0.198 10 false *a 1.646,0.281 1.958,0.479 0.313,0.198 10 false a34 0.885,1.51 1.5,1.708 0.615,0.198 10 false IG 2.583,1.698 3.198,1.896 0.615,0.198 10 false GND
*a Front view of wire harness connector
(to Seat Cushion Climate Control Blower Assembly RH)


Disconnect the a34 seat cushion climate control blower assembly RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
a34-1 (IG) - Body ground Power switch on (IG) 11 to 14 V
a34-1 (IG) - Body ground Power switch off Below 1 V


Standard Resistance:
Tester Connection Condition Specified Condition
a34-8 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY RH - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY RH - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the K54 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
a34-7 (SIGN) - K54-23 (ROUT) Always Below 1 Ω
a34-7 (SIGN) or K54-23 (ROUT) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

18.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Reconnect the K54 air conditioning amplifier assembly connector.


b.
B416364C10
1.75,0.5 2.167,0.75 0.417,0.25 1.604,1.875 1.917,1.385 true 0.281,0.167 0.594,0.365 0.313,0.198 10 false *a 1.844,0.531 2.156,0.729 0.313,0.198 10 false K54 0.323,3.958 0.781,4.156 0.458,0.198 10 false GND 1.448,1.927 2.063,2.125 0.615,0.198 10 false ROUT
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Reconnect the a34 seat cushion climate control blower assembly RH connector.


c.

Using an oscilloscope, check the input signal waveform.

Measurement Condition
Item Content
Tester Connection K54-23 (ROUT) - Body ground
Tool Setting 1 V/DIV., 0.5 ms/DIV.
Vehicle Condition
·

Power switch on (IG)

·

Refreshing seat switch on

(blower position)



OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY RH

NG

19.REPLACE REFRESHING SEAT SWITCH
19.REPLACE REFRESHING SEAT SWITCH
a.

Temporarily replace the refreshing seat switch with a new or known good one.

Click hereVehicle Interior>SEAT>SEAT HEATER SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

20.CHECK CLIMATE CONTROL SEAT OPERATION
20.CHECK CLIMATE CONTROL SEAT OPERATION
a.

Check the climate control seat operation.

Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>ON-VEHICLE INSPECTION

OK:

The climate control seat operates normally.



Result:
Proceed to
OK
NG



OK

END (REFRESHING SEAT SWITCH WAS DEFECTIVE)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

21.INSPECT S/HTR F/R RELAY
a.
B256934C02
2.198,0.917 2.198,0.5 2.198,0.5 2.031,0.5 true 2.031,1.885 2.198,1.885 2.198,1.885 2.198,1.469 true 2.646,1.885 2.479,1.885 2.479,1.885 2.479,1.365 true 2.823,1 2.823,0.5 2.823,0.5 2.656,0.5 true 0.104,0.083 0.417,0.396 0.313,0.313 10 false *1 0.323,1.458 0.573,1.75 0.25,0.292 10 false 5 1.313,0.667 1.594,0.917 0.281,0.25 10 false 2 0.313,0.667 0.51,0.906 0.198,0.24 10 false 1 1.313,1.469 1.563,1.708 0.25,0.24 10 false 3 2.708,1.792 2.927,2.01 0.219,0.219 10 false 5 1.833,1.771 2.063,2 0.229,0.229 10 false 1 1.917,0.417 2.208,0.688 0.292,0.271 10 false 2 2.542,0.417 2.813,0.708 0.271,0.292 10 false 3
*1 S/HTR F/R Relay


Remove the S/HTR F/R relay from the No. 6 relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

22.CHECK HARNESS AND CONNECTOR (POWER SUPPLY - S/HTR F/R RELAY)

NG

REPLACE S/HTR F/R RELAY

22.CHECK HARNESS AND CONNECTOR (POWER SUPPLY - S/HTR F/R RELAY)
a.
B530042C01
0.146,0.125 0.479,0.438 0.333,0.313 10 false *a
*a S/HTR F/R Relay Holder


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
No. 6 relay block S/HTR F/R relay terminal 1 - Body ground Power switch off Below 1 V
No. 6 relay block S/HTR F/R relay terminal 1 - Body ground Power switch on (IG) 11 to 14 V
No. 6 relay block S/HTR F/R relay terminal 5 - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

23.CHECK HARNESS AND CONNECTOR (S/HTR F/R RELAY - SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.CHECK HARNESS AND CONNECTOR (S/HTR F/R RELAY - SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY RH)
a.
B530042C01
0.146,0.125 0.479,0.438 0.333,0.313 10 false *a
*a S/HTR F/R Relay Holder


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 6 relay block S/HTR F/R relay terminal 3 - a34-1 (IG) Always Below 1 Ω
No. 6 relay block S/HTR F/R relay terminal 3 or a34-1 (IG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

24.CHECK HARNESS AND CONNECTOR (S/HTR F/R RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.CHECK HARNESS AND CONNECTOR (S/HTR F/R RELAY - BODY GROUND)
a.
B530042C01
0.146,0.125 0.479,0.438 0.333,0.313 10 false *a
*a S/HTR F/R Relay Holder


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 6 relay block S/HTR F/R relay terminal 2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

25.CHECK HARNESS AND CONNECTOR (IG POWER SUPPLY - REFRESHING SEAT SWITCH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.CHECK HARNESS AND CONNECTOR (IG POWER SUPPLY - REFRESHING SEAT SWITCH - BODY GROUND)
a.

Disconnect the K49 refreshing seat switch connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K49-1 (IG) - Body ground Power switch on (IG) 11 to 14 V
K49-1 (IG) - Body ground Power switch off Below 1 V


Standard Resistance:
Tester Connection Condition Specified Condition
K49-5 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

26.REPLACE REFRESHING SEAT SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.REPLACE REFRESHING SEAT SWITCH
a.

Temporarily replace the refreshing seat switch with a new or known good one.

Click hereVehicle Interior>SEAT>SEAT HEATER SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

27.CHECK CLIMATE CONTROL SEAT OPERATION
27.CHECK CLIMATE CONTROL SEAT OPERATION
a.

Check the climate control seat operation.

Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>ON-VEHICLE INSPECTION

OK:

The climate control seat operates normally.



Result:
Proceed to
OK
NG



OK

END (REFRESHING SEAT SWITCH WAS DEFECTIVE)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY